Related Manuals for Oertzen E 500-17
Summary of Contents for Oertzen E 500-17
- Page 1 To be read completely before initial start-up! Operating Manual E 500-17 9/08 von Oertzen GmbH • Ferdinand-Harten-Str. 10 • 22949 Ammersbek • Tel. +49 40 604110 • Fax +49 40 6041149 www.oertzen-gmbh.de • info@oertzen-gmbh.de...
-
Page 2: Table Of Contents
Table of Content Introduction Page Safety Instructions Page 4 – 5 Design/Configuration/Illustrations Page 6 – 7 Start-up/Shut-down Operation Page 8 – 10 Maintenance and Care Page 11 – 12 Electric Wiring Diagram Page Technical Data Page Trouble Shooting Page Declaration of Conformity Page... -
Page 3: Introduction
Introduction With your OERTZEN high pressure cleaner you have purchased one of the most durable and reliable machines available on the market. Its balanced ratio of water flow (temperature) and working pressure perfectly meets all cleaning requirements. The OERTZEN high pressure cleaners conform to all European safety regulations which is guaranteed by the CE symbol. -
Page 4: Safety Instructions
Unsuitable respectively defective high pressure hoses often cause severe accidents during operation. Therefore high pressure hoses to be carefully inspected before start-up and replaced by original OERTZEN equipment in case of damage. Use of other than original OERTZEN equipment results in expiration of the EC Declaration of Conformity, as well as product liability and warranty. - Page 5 After work the machine to be locked and secured against unauthorized/accidental operation by means of the safety lever. Use of equipment and/or consumables which is not delivered or expressively approved by OERTZEN results in expiration of the EC Declaration of Conformity, as well as product liability and warranty.
- Page 6 When activating the spray pistol again, adjusted working pressure is generated immediately so that the cleaning task can be continued without delay. The range of applications can be extended by a variety of accessories available from OERTZEN. Contact your local distributor.
-
Page 8: Start-Up/Shut-Down Operation
• Filling of consumables. • Correct oil level of high pressure pump (sight glass/dip stick). • High pressure pump: OERTZEN OSP special pump oil. • Pump/pump connections whether leaking. • Machine only to be run with absolutely clean water. Before connecting the water supply hose, rinse it thoroughly. - Page 9 Power Supply Insert plug into a 440 V socket which is protected by 3 x 63 A (slow). Only extension cables designed according to VDE to be used. Extension cables on reels to be reeled off during operation in order to avoid overheating of the reel. Plug, couplings to be watertight.
- Page 10 Thoroughly clean high pressure hose. In case of damage (cuts, abrasions, kinks, etc.) replace high pressure hose for safety reasons. Only original OERTZEN high pressure hoses (marked) to be used. Otherwise EC Declaration of Conformity and warranty will expire. Reel up high pressure hose properly without any loops.
-
Page 11: Maintenance And Care
High Pressure Pump First oil change after 50 operating hours, further oil changes after every 500 operating hours, minimum once per year. Only OERTZEN OSP special pump oil to be used. Use of other oil qualities results in expiration of warranty. - Page 12 Micro Filter A micro filter (5) is arranged at the water inlet, the insert of which must be checked before start-up and replaced whenever necessary. If the machine is operated with polluted water or dirty filter inserts heavy damage on the pump set and/or control elements will be the result.
-
Page 13: Electric Wiring Diagram
Electric Wiring Diagram Technische Daten Technical Data Technical Data E 500-17 Water flow 1020 l/h Unloading pressure 550 bar Working pressure 500 bar Normal current (60 Hz) 3 ~ 440 V Power consumption 18 kW Amperage 27 A Sound pressure level/sound power level 69 /81 dB(A) acc. -
Page 14: Trouble Shooting
During maintenance/repair work, disconnect machine from power source. Repair work only to be carried out by qualified service personnel. Only original OERTZEN spare parts/accessories to be used, otherwise working safety will not be guaranteed, EC Declaration of Conformity will expire.