Related Manuals for Oertzen S 323 VA
Summary of Contents for Oertzen S 323 VA
- Page 1 Manual to be read before initial start-up! Operation Manual S 323 VA S 323 VA-H von Oertzen GmbH • Ferdinand-Harten-Str. 10 • 22949 Ammersbek • Tel. +49 40 604110 • Fax +49 40 6041149 www.oertzen-gmbh.de • info@oertzen-gmbh.de...
-
Page 2: Table Of Contents
Table of Contents Introduction page Safety Instructions page 4 – 5 Design and Configuration/Illustrations page 6 – 7 Start-up/Operation/Shut-down page 8 – 11 Maintenance and Care page 12 – 13 Electric Wiring Diagram page Technical Data page Trouble Shooting page Declaration of Conformity page... -
Page 3: Introduction
Introduction By buying the OERTZEN equipment you have purchased one of the most durable and reliable high pressure cleaners available on the market. Its balanced ratio of water flow (temperature) and working pressure perfectly meets all cleaning requirements. The OERTZEN high pressure cleaners and accessories conform to all European safety regulations which is guaranteed by the CE symbol on the type plate. -
Page 4: Safety Instructions
Unsuitable respectively defective high pressure hoses often cause severe accidents during operation. Therefore high pressure hoses to be carefully inspected before start-up and replaced by original OERTZEN equipment in case of damage. Use of other than original OERTZEN equipment (hand nut marked with OERTZEN), results in expiration of the EC Declaration of Conformity, as well as product liability and warranty. - Page 5 After work the machine to be locked and secured against unauthorized/accidental operation by means of the safety lever. Use of equipment and/or consumables which is/are not delivered or expressively approved by OERTZEN results in expiration of the EC Declaration of Conformity, as well as product liability and warranty.
- Page 6 Configuration, Operation, Illustration The machines of this series are designed to be fixed into a suitable piping system with several tap points. Connecting additional spray equipment allows to carry out cleaning jobs at two places in parallel, independently of each other.
-
Page 8: Start-Up/Operation/Shut-Down
• Filling of consumables. • Correct oil level of high pressure pump (sight glass/dip stick). • High pressure pump: special pump oil OERTZEN OSP. • Pump/pump connections whether leaking. • Machine only to be run with absolutely clean water. Before connecting the water supply hose, rinse it thoroughly. - Page 9 Power Supply Insert plug into a 400 V socket which is protected by 3 x 63 A (slow). Only extension cables designed according to VDE to be used. Extension cables on reels to be reeled off during operation in order to avoid overheating of the reel. Plug, couplings to be watertight.
- Page 10 Detergent Mode (Option – Injector Kit) Only detergents approved by OERTZEN to be used. Warranty will expire in case hazardous detergents or detergents not approved by OERTZEN will be used Put detergent hose with strainer into a vessel with detergent liquid.
- Page 11 (cuts, abrasions, kinks, etc.) replace high pressure hose for safety reasons. • Only original OERTZEN high pressure hoses to be used. Otherwise Declaration of Conformity and warranty will expire. • Reel up high pressure hose properly without any loops.
-
Page 12: Maintenance And Care
If this happens repeatedly, arrange replacement of all pump seals and packings by qualified personnel. For the high pressure pump only special pump oil OERTZEN OSP to be used, as otherwise you will loose your right to claim under parts guarantee. - Page 13 Pre-Filter Upstream of the high pressure pump there is a pre-filter (6) installed, which must be inspected before start-up and cartridge replaced whenever required. If the machine is run with polluted water or dirty pre-filter severe damage of the pump and control elements will be the result. Frost Protection Frost protection of the entire water system during storage and transport is a must, as otherwise heavy damage on the system and severe...
-
Page 14: Electric Wiring Diagram
Electric Wiring Diagram Technical Data Technical Data S 323 VA S 323 VA-H Water flow/adjustable 1380 l/h 1380 l/h Unloading pressure 140 bar 230 bar Max. working pressure 120 bar 120 bar Max. recoil 54 N 83 N Suction height... -
Page 15: Trouble Shooting
Trouble Shooting Electric power can cause severe injuries. Defective electrical compo- nents to be immediately replaced, possible causes for accidents to be eliminated without delay. Any repair work must only be carried out by qualified personnel. Only original equipment expressively approved by the manufacturer to be installed, as otherwise warranty and Declaration of Conformity will cease, health and safety standards are not guaranteed.