Related Manuals for Oertzen 311 C
Summary of Contents for Oertzen 311 C
- Page 1 Operation Manual 311 C 316 C 11/08 von Oertzen GmbH • Ferdinand-Harten-Str. 10 • 22949 Ammersbek • Tel. +49 40 604110 • Fax +49 40 6041149 www.oertzen-gmbh.de • info@oertzen-gmbh.de...
-
Page 2: Table Of Contents
Table of Content Introduction Page Safety Instructions Page 4 - 5 Design/Configuration/Illustration Page 6 - 7 Start-up/Shut-down Page 8 - 11 Maintenance & Care Page 12 - 13 Electric Wiring Diagram Page 14 Technical Data Page 14 Trouble Shooting Page 15 Declaration of Conformity Page 16... -
Page 3: Introduction
Introduction By buying this OERTZEN high pressure cleaner, you have obtained a most capable machine suitable to perfectly meet your cleaning tasks. All OERTZEN machines and accessories conform to the National and European Safety Regulations. The CE label guarantees for fulfilment of all relevant National and European Safety Regulations (EN). -
Page 4: Safety Instructions
Defective hoses immediately to be replaced by original OERTZEN equipment. Using other materials than original OERTZEN equip- ment (hand nut respectively hose marked with “OERTZEN”) or using materials which have not expressively been approved by OERTZEN in writing ceases warranty and product liability. - Page 5 After work spray pistol to be locked by means of the safety lever in order to avoid unauthorised/accidental operation. Using other materials than original OERTZEN equipment or using materials which have not expressively been approved by OERTZEN in writing ceases EC conformity, warranty and product liability.
-
Page 6: Design/Configuration/Illustration
A wide range of accessories which allow to increase the efficiency of the machine is available. Contact OERTZEN or your local dealer for details. -
Page 8: Start-Up/Shut-Down
• Fill in all consumables required • Check correct oil level of high pressure pump (dip stick), only oil qualities approved by OERTZEN to be used (OERTZEN OSP special pump oil). • Check high pressure pump/pump connections for leaks • Machine only to be run with absolutely clean water. Thoroughly flush water supply hose before connection. - Page 9 Electric Connection Connect the unit to a power source which is protected according to table below. 311 C 316 C Power supply 230 Volt 400 Volt Protection 16 A (slow) 3 x 16 A (slow) Extension cables to have a diameter according to VDE regulations. Extension cables on reels to be reeled off completely, in order to avoid overheating of the cable reel.
- Page 10 Clockwise: pressure increase Detergent Dosing Only detergents approved by OERTZEN to be used. Use of hazardous detergents or detergents not approved by OERTZEN ceases warranty and product liability. Open the detergent dosing valve(16). Open the valve of the double lance completely (turn counter-clockwise) and activate spray pistol.
- Page 11 Reel off high pressure hose and thoroughly clean it. In case of damage replace it for safety reasons. Using other materials than original OERTZEN equipment (hand nut respec- tively hose marked with “OERTZEN”) or using materials which have not expressively been approved by OERTZEN in writing ceases warranty and product liability.
-
Page 12: Maintenance & Care
OERTZEN service personnel. In case the pump oil is becoming turbid, initiate oil change. In case oil is becoming turbid again or is being lost, call qualified service. Only OERTZEN OSP special pump oil to be used. Use of oil qualities not approved by OERTZEN ceases warranty. - Page 13 Strainer A strainer (6) is installed at the water inlet of the machine which must be checked and cleaned, respectively replaced whenever needed. Severe damage on pump set and control units can be caused by running the machine with polluted feed water and/or clogged strainer. Frost Protection Frost-protection of the machine is of vital interest, as frost can cause severe damage on the entire system.
-
Page 14: Electric Wiring Diagram
Technical Data Technical Data 311 C 316 C Flow rate/adjustable 600 l/h 780 l/h Unloading pressure 160 bar 200 bar Max. working pressure 140 bar 180 bar Max. recoil 28 N 49 n Max. water temperature 50 °C 50 °C... -
Page 15: Trouble Shooting
Trouble Shooting Electrical energy can cause severe injuries. Electrical components tho- roughly and frequently to be checked for damages and malfunctions, in order to avoid any cause for accidents. Disconnect the unit from the electrical network during all repair/maintenance work (ZH 1/95). Trouble Shooting: - only to be carried out by qualified service personnel.