Related Manuals for Gree EVO Series
Summary of Contents for Gree EVO Series
- Page 1 G R E E Thank you for choosing GREE air conditioners. For proper operation, please read this owner's manual carefully before operating the unit and save it for future reference.
-
Page 3: Check After Installation
Operation of wireless remote control ........1 ......1 maintenance ........1 ........1 ......1 ..............2 ....2 Check after installation test operation ........2 Malfunction Codes indicates that indicates hat not be attempted or are prohibited GREE store future reference to the material objects for... - Page 4 Unit must be properly grounded Setting at extreme tempera- tures can cause improper operation prolonged periods and excessive energy consumption. Please consult a qualified technician. all combustibles from doors the units and the conditioned space . prolonged periods while system capacity. It can decrease the system capacity or cause a malfunction.
-
Page 5: Notices For Operation
Notices for operation .Ajust the If the supply cord is damaged, it must be replaced direction by adjusting the louvers by the manufacturer or its service agent or a wnward direction.Then,ajust the left qualified technician in order to avoid a and right louvers for horizontal air-flow. - Page 6 115 84 115/82 61 52 41/- 86 73 5/1.4 The operating temperature range (outdoor temperature) for cooling unit is 41~ 1 1 5 for cooling and heating unit is 5~ 1 1 5...
-
Page 7: Names And Functions Of Each Part
Names and functions of each part Indoor unit Air in Air out Wireless remote control Display icon: Power cable Receiver Cooling Heating Front panel Filter Guide louver Set temp. Power/Run Dehumidify Wall pipe Outdoor unit Bind tape Air in Connection wire Drainage pipe Air out... -
Page 8: Operation Of Wireless Remote Control
Operation of wireless remote control Name and function of wireless remote control Note: Be sure that there are no obstructions between receiver and remote controller; Don't drop or throw the remote control; Don't let any liquid in the remote control.Do not put the remote control directly under the sunlight or any place where is very hot. - Page 9 Operation of wireless remote control Names and functions of wireless remote control Notice: This is a universally used remote control shows all the fuctions.Some functions may not to be carried out depending on the actual models, if press the corresponding button on the remote control that the unit will not receive this signal and will keep the original running status.
-
Page 10: Air Button
Operation of wireless remote control Name and function of wireless remote control Notice: This is a universally used remote control shows all the fuctions.Some functions may not to be carried out depending on the actual models, if press the corresponding button on the remote control that the unit will not receive this signal and will keep the original running status. - Page 11 Operation of wireless remote control Guide for operation- general operation Guide for operation- Optional operation or timer off. Introduction for special function About Blow over heat function About AUTO RUN About turbo function...
- Page 12 Operation of wireless remote control Lock Press +and - buttons simultaneously to lock or unlock the keyboard. If the remote controller is locked, the icon will be displayed, in which case, press any button, the icon will flicker three times. If the keyboard is unlocked, the icon will disappear. Swing up and down function 1.
-
Page 13: Manual Operation
Manual Operation Permits the turning off of the display light. To turn on display light : When setting the light function,the icon will pressing . In which case,the dis- play indicator light will be on if the AC receives To turn off display light icon will dis- apper this button. -
Page 14: Clean And Care
Clean and care electric s to an electric shock. i.e. mild use a soft moistened with water below 113 then completely dry the surface erlectronic above normal more often do not injuries Open the front remove Clean and mild close the front panel... - Page 15 Clean and care new batterieshave been installed in the remote control in good condition and property anchored.I service center any corrosion spots spreading. from entering.
-
Page 16: Troubleshooting
Troubleshooting Event Unit does n persists, conditioner. through the system if is not considered malfunction sand is emitted fade... - Page 17 Event Are the inside pipe mode water...
-
Page 18: Installing Contractor
Event indoor will stop deliver air. (Within 2min) fan will water be vapo- rized rising. the unit contact installing contractor... - Page 19 98.4 in. Make sure that the indoor unit installation should accord with installation dimension diagram requirements. 16.4 ft. 32.8 ft.
-
Page 20: Notices For Installation
Notices for installation the installation work should be operatedbythe professional. 4. The minimum distance from the unit and combustive surface is 4.9 ft.. 5. The appliance shall be installed in accordance with national wiring regulations. An all-pole disconnection switch having a contact separation of at least 0.12 in. in all poles should be connected in fixed wiring. -
Page 21: Installation Dimension Diagram
Installation dimension diagram Installation dimension diagram Space to the ceiling 0.5ft. Above Space to the wall 0.5ft Above 0.5ft Above Space to the wall 9.8 ft Above Air outlet side The dimensions of the space necessary for correct installation of the appliance including the minimum permissible distances to adjacent structures 1.64ft. - Page 22 both-way drainage taking the outlet of the water tray level should be 0 or more, that is good for 5.9 in. firmly adult of 132.3 lb., 5.9in. should be evenly shared by 2.2in. 2.2in 2.2in. 2.2in. 1.Open the surface panel. 2.Remove the wiring cover(Fig.6).
- Page 23 NOTE: 8.2ft. 7/11...
-
Page 24: Install Outdoor Unit
Install outdoor unit Electric wiring For 18K UNIT: Disassemble the handle on the outdoor unit right side plate. Take off wire clamp. Connect and fix power connect cord (for cooling and heating unit,connect and fix power connect cord and signal control wire)to terminal of line bank. - Page 25 pressure shut). Manifold Valve Multimeter Manometer -76cmHg Open the vacuum pump to evacuate. At the beginning, slightly Lo Handle Hi handle loosen joint nut of low pressure valve to check if there Charging hose is air coming inside. (If noise of vacuum pump has Charging hose been changed, the reading of multimeter is 0) Then Vacuum pump...
- Page 27 Malfunction Tab Disp lay o f doubl e Disp lay o f lamp Name of malfunct io n eight code Runni ng lamp Coolin g lamp Heating lamp Refrigerant system high pressure protection blink 1 time Anti-freezing protection blink 2 times Compressor exhaust high temperature protection blink 4 times AC over-current protection...
- Page 28 66129903999...