Roland V-440HD Owner's Manual page 71

* The following controls correspond to each Bank Select message.
--------------------------------------------------------------------------------------------
Bank Select Program No.
MSB/LSB
--------------------------------------------------------------------------------------------
00H/00H 00H - 03H
--------------------------------------------------------------------------------------------
01H/00H 00H - 03H
--------------------------------------------------------------------------------------------
02H/00H 00H - 04H
-------------------------------------------------------------------------------------------
03H/00H 00H - 04H
--------------------------------------------------------------------------------------------
❍Modulation (controller number 1)
Status 2nd byte
BnH 01H
❍Breath-type (controller number 2)
Status 2nd byte
BnH 02H
❍Foot-type (controller number 4)
Status 2nd byte
BnH 04H
❍Portamento Time (controller number 5)
Status 2nd byte
BnH 05H
❍Volume (controller number 7)
Status 2nd byte
BnH 07H
❍Balance (controller number 8)
Status 2nd byte
BnH 08H
❍Panpot (controller number 10)
Status 2nd byte
BnH 0AH
❍Expression (controller number 11)
Status 2nd byte
BnH 0BH
❍Effect Control 1 (controller number 12)
Status 2nd byte
BnH 0CH
❍Effect Control 2 (controller number 13)
Status 2nd byte
BnH 0DH
❍General Purpose Controllers 1–4 (controller numbers 16-19)
Status 2nd byte
BnH 10H - 13H
❍Hold 1 (controller number 64)
Status 2nd byte
BnH 40H
❍Portamento (controller number 65)
Status 2nd byte
BnH 41H
❍Sostenuto (controller number 66)
Status 2nd byte
BnH 42H
❍Soft (controller number 67)
Status 2nd byte
BnH 43H
Control
A ch, INPUT 1-4
B ch, INPUT 1-4
C ch, INPUT AB-4
D ch, INPUT AB-4
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
xxH
3rd byte
xxH
3rd byte
xxH
3rd byte
xxH
❍Legato (controller number 68)
Status 2nd byte
BnH 44H
❍Hold 2 (controller number 69)
Status 2nd byte
BnH 45H
❍Sound Controllers 1–10 (controller numbers 70–79)
Status 2nd byte
BnH 46 - 4FH
❍General Purpose Controllers 5–8 (controller numbers 80–83)
Status 2nd byte
BnH 50 - 53FH
❍Portamento Control (controller number 84)
Status 2nd byte
BnH 54H
❍Effect Depth 2–5 (controller number 92–95)
Status 2nd byte
BnH 5C - 5FH
●Program Change
Status 2nd byte
CnH ppH
pp= program number:00H - 7FH (prog.1 - prog.128)
* When you select channel A or channel B inputs, make memory settings, or specify how
sub-channels are mixed in Presentation mode, these messages will be transmitted in
conjunction with Bank Select messages. For details, refer to the section on Bank Select.
●Channel Pressure
Status 2nd byte
DnH vvH
* Just as for Control Changes, the messages assigned in MIDI Setup will be transmitted
when you operate the panel. For the factory settings, refer to "Settings Transmitted/
Received Using MIDI" (p. 75).
●Pitch Bend Change
Status 2nd byte
EnH llH
mm, ll= pitch bend value:00 00H - 40 00H - 7F 7FH (-8192 - 0 -+8191)
* Just as for Control Changes, the messages assigned in MIDI Setup will be transmitted
when you operate the panel. For the factory settings, refer to "Settings Transmitted/
Received Using MIDI" (p. 75).
●Data Set 1 (DT1)
This is the message that transfers actual data, and is used to specify data for a device.
Status Data bytes
F0H 41H, dev, 00H, 00H, 10H, 12H,
aaH, bbH, ccH, ddH, ..., eeH, sum
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
dev Device ID (dev: 00H–1FH, factory setting is 10H)
00H 1st byte of model ID (V-440HD)
00H 2nd byte of model ID (V-440HD)
10H 3rd byte of model ID (V-440HD)
12H Command ID (DT1)
aaH Upper byte of address
bbH Address
ccH Address
ddH Data: the actual data to be transmitted. Multi-byte data is transmitted
in the order of the address.
: :
eeH Data
sum Checksum
F7H EOX (End Of Exclusive)
* For details on setting the address, size, and checksum, refer to "Example of exclusive
message and checksum calculation".
* Data that exceeds 256 bytes must be divided into packets of 256 bytes or less for
transmission. If a subsequent "Data Set 1" message is transmitted, an interval of at least
20 ms must be left between packets.
MIDI implementation
3rd byte
xxH
3rd byte
xxH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
Status
F7H
71