Table of Contents
Advertisement
ENGLISH
Features
This tool includes some or all of the following features.
1. On/off switch
2. Bowl release button
3. Charging indicator
4. Charging socket
5. Dust bowl
6. Dust collector
Assembly
Accessories (fig. A, B & C)
These models may be supplied with some of the following
accessories:
A brush tool (7) for furniture and stairs.
u
An Integrated brush tool (8) for furniture and stairs.
u
An Integrated crevice tool (9) for confined spaces.
u
Fitting the brush tool (Fig. A). (DV7210ECN Only)
Insert the accessory into the front of the appliance. Make
u
sure that the accessory is pushed fully in.
The integrated brush tool (Fig. B). (DV9610ECN and
DV1210ECN Only)
Flip down the brush tool (8) at the end of the dust collec-
u
tor.
The integrated crevice tool (Fig. C). (DV9610ECN and
DV1210ECN Only)
Extend the crevice tool (9) by pulling the crevice tool (9)
u
until it locks into position.
Retract the crevice tool (9) by pressing the area (10) and
u
pushing the crevice tool (9) back into the dust collector (6).
Use
Before first use, the battery must be charged for at least
u
24 hours.
Charging the battery (Fig. D)
Make sure that the appliance is switched off. The battery
u
will not be charged with the on/off switch in the on posi-
tion.
Plug the jack plug of the charger (11) into the charging
u
socket (4) of the appliance (Fig. D).
Plug in the charger. Switch on at the mains. The charging
u
indicator (3) will be lit.
Leave the appliance to charge for at least 16 hours.
u
6
(Original instructions)
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
be left connected to the charger indefinitely. The charging
indicator (3) will be lit as long as the appliance is connected to
the plugged-in charger.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C.
Switching on and off (fig. E)
To switch the appliance on, slide the on/off switch (1)
u
forward to position 1.
To switch the appliance off, slide the on/off switch (1) back
u
to position 0.
Rotating the dust collector (fig. F) (DV9610ECN &
DV1210ECN only
The nozzle can be rotated for better access in tight spots.
Press the rotation release catch (12).
u
Rotate the nozzle to the left or right until it clicks into
u
place.
Optimising the suction force
In order to keep the suction force optimised, the filters must be
cleared regularly during use.
Emptying and cleaning the product.
Emptying the dust bowl (fig. G).
Press the release latchs (13) and pull the dust collector (6)
u
straight off.
Empty the contents of the bowl.
u
To replace the dust collector, place it back onto the handle
u
until it "clicks" firmly into position.
Removing the dust bowl and filters (fig. H, I, J & K).
Warning! The filters are re-usable and should be cleaned
regularly.
Press the release latch (2) and pull the dust bowl (5)
u
straight off.
While holding the dust bowl over a bin or sink, pull out the
u
filter (14) to empty the contents of the bowl.
To replace the dust bowl, place it back onto the handle
u
until it "clicks" firmly into position.
Warning! Never use the appliance without the filters. Opti-
mum dust collection will only be achieved with clean filters.
Pre-filter (fig. J) (DV7210ECN)
The Filter and pre-filter can be separated to allow better
cleaning.
Twist the pre-filter (15) in a clockwise direction and lift
u
from the filter (14).
Advertisement
Table of Contents
