Indoor Unit Installation; Installing The Wall Hang Bracket - Carrier P1 Plus series Owners And Installation Manual

INDOOR UNIT INSTALLATION

• The piping can be connected to the four directions indicated by ³, ·, », ¿.
When the piping is connected to the direction of
out either at the side or at the bottom of the unit. ( Fig. 3 )
»
³
·
³
·
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4

1) Installing the Wall Hang Bracket

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4
24
Page 24
, or , detach the knock-
¿
• Install the wall hang bracket so that it is level. Use a plumb line if necessary.
( Figure. 4 )
• Be sure to leave the clearance spaces shown in Figure 1.
• Before installing the wall hang bracket, remove it from the unit by pushing up
¿
marks (
• Fasten the wall hang bracket to the wall with 5 or more self-tapping screws
through the holes near the outer edge of the bracket as shown in Figure 4.
Figure 3
• Install the wall hang bracket so that there is no gap between the bracket and the wall.
• Check that the wall hang bracket does not move to prevent noise during
operation.
NOTE
• In case of removing the unit from the wall hang bracket after installing it
onto the wall, remove by pushing up MARKS ( ) at the bottom of
the body.
REMOVE SCREW
10cm
or more
30cm
or more
PLUMB
) at the bottom of the body.
2004.6.11, 3:15 PM
45cm
or more
Figure 4