5.25 inch motherboard intel atom processor, vga/lvds dual display, quad gbe, eight usb 2,0, two sata 3 gb/s, two pcle mini, pci, pci-104,rohs (194 pages)
Intel socket479 motherboard supporting intel pentium m and celeron m processors and both vga and dual lvds graphics output with dual pcie gbe, usb 2.0, sata and audio (266 pages)
Page 2
NOVA-LX 5.25” Motherboard Revision Date Version Changes 2008-03-31 1.00 Initial release Page ii...
Page 3
NOVA-LX 5.25” Motherboard Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Page 4
Cautionary messages should also be heeded to help reduce the chance of losing data or damaging the NOVA-LX. Cautions are easy to recognize. The word “caution” is written as “CAUTION,” both capitalized and bold and is followed. The italicized text is the cautionary message.
Page 5
NOVA-LX 5.25” Motherboard CAUTION: This is an example of a caution message. Failure to adhere to cautions messages may result in permanent damage to the NOVA-LX. Please take caution messages seriously. NOTE: These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes.
NOVA-LX from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. The items listed below should all be included in the NOVA-LX package. 1 x NOVA-LX single board computer 1 x mini jumper pack...
Page 9
NOVA-LX 5.25” Motherboard 4.2.1 ATX +12V Power Connector ................42 4.2.2 ATX Power Supply Enable Connector ............. 43 4.2.3 Audio CD In Connector (4-pin) ............... 44 4.2.4 Audio Connector (10-pin) ................45 4.2.5 Backlight Inverter Connector ................46 4.2.6 Fan Connector (+12V) (System Cooling Fans)..........47 4.2.7 Floppy Disk Connector (34-pin)..............
Page 10
NOVA-LX 5.25” Motherboard 5.5.3 CF Card Setup ....................78 5.5.4 Clear CMOS Jumper..................79 5.5.5 COM 1/2 Pin 9 Setting Jumper................ 80 5.5.6 COM 3/4 Function Select Jumper..............81 5.5.7 LCD Clock Select Jumper ................82 5.5.8 LCD Voltage Selection ..................83 5.5.9 PCI-104 Serial IRQ Selector ................
Page 11
NOVA-LX 5.25” Motherboard 6.3.3 Floppy Configuration..................112 6.3.4 Super IO Configuration...................113 6.3.5 Hardware Health Configuration..............118 6.3.6 Smbios ......................120 6.3.7 Remote Access Configuration ................ 121 6.3.8 USB Configuration..................125 6.3.9 IT8888 Configuration ..................126 6.3.9.1 ISA Decode IO Spaces................127 6.3.9.2 ISA Decode Memory Spaces ..............130 6.3.10 Power ......................
Page 12
NOVA-LX 5.25” Motherboard C.3.2 Enable the DIO Output Function ..............186 WATCHDOG TIMER ..................187 ADDRESS MAPPING..................190 E.1 A ....................... 191 DDRESS E.2 1 MB M ................191 EMORY DDRESS E.3 IRQ M .................... 192 APPING ABLE E.4 DMA C ................
Page 19
NOVA-LX 5.25” Motherboard BIOS Menus Menu 1: Main......................101 Menu 2: Advanced....................103 Menu 3: CPU Configuration..................104 Menu 4: IDE Configuration ..................105 Menu 5: IDE Master and IDE Slave Configuration ..........107 BIOS Menu 6: Floppy Configuration ...............112 Menu 7: Super IO Configuration ................113...
1.1 Overview Figure 1-1: NOVA-LX Motherboard The NOVA-LX 5.25” form factor motherboard is an AMD Geode™ LX 800 platform with 256 MB of on-board DDR SDRAM, support for dual 10/100 Mbps Ethernet, eight serial ports, digital I/O interface and audio. The NOVA-LX also supports multiple display unit types including VGA, LVDS and TTL.
NOVA-LX 5.25” Motherboard 1.2 NOVA-LX Overview 1.2.1 NOVA-LX Overview Photo The NOVA-LX has a wide variety of peripheral interface connectors. Figure 1-2 is a labeled photo of the peripheral interface connectors on the NOVA-LX. Figure 1-2: NOVA-LX Overview [Front View] 1.2.2 NOVA-LX Peripheral Connectors and Jumpers...
Page 24
2 x RS-232/422/485 serial port connector 1 x TTL connector 2 x USB 2.0 connectors (support four USB devices) 1 x VGA connector The NOVA-LX has the following external peripheral interface connectors on the board rear panel 2 x Ethernet connectors 1 x PS/2 connectors...
NOVA-LX 5.25” Motherboard PCI-104 Voltage Setup PC/104-Plus SERIRQ Select 1.2.3 Technical Specifications NOVA-LX technical specifications are listed in Table 1-1. See Chapter 2 for details. Specification NOVA-LX Form Factor 5.25” System CPU AMD Geode™ LX 800 System Chipset AMD Geode™ CS5536...
NOVA-LX 5.25” Motherboard 2.1 Dimensions 2.1.1 Board Dimensions The dimensions of the board are listed below: Length: 203 mm Width: 146 mm Figure 2-1: NOVA-LX Dimensions (mm) Page 8...
NOVA-LX 5.25” Motherboard 2.1.2 External Interface Panel Dimensions External peripheral interface connector panel dimensions are shown in Figure 2-2. Figure 2-2: External Interface Panel Dimensions (mm) 2.2 Data Flow Figure 2-3 shows the data flow between the two on-board chipsets and other components installed on the motherboard and described in the following sections of this chapter.
The AMD Geode™ LX 800 supports 64-bit DDR memory modules with frequencies up to 400 MHz. The NOVA-LX has four optional preinstalled DDR SDRAM memory modules. Each memory module has a capacity 64 MB. The 512 Mb (64 MB) DDR SDRAM modules have a clock frequency of 200 MHz and a maximum data transmission rate of 200 Mbps per pin.
NOVA-LX 5.25” Motherboard Figure 2-4: Memory Modules ® 2.3.3 AMD Geode™ LX 800 500MHz Display Support ® The AMD Geode™ LX 800 supports both CRT and TFT in a dual display mode. The following display specifications. Supported Standards High Definition (HD)
NOVA-LX 5.25” Motherboard and the ability to throttle BLTs according to video timing. New features added to the Graphics Processor include: Command buffer interface Hardware accelerated rotation BLTs Color depth conversion Paletized color Full 8x8 color pattern buffer Separate base addresses for all channels Monochrome inversion Table 2-1: Geode LX Graphics Features lists a complete list of Geode™...
Lower power I/O Wakeup on SMI/INTR 2.4 AMD Geode™ CS5536 System Chipset The NOVA-LX series motherboards all have a preinstalled AMD Geode™ CS5536 system chipset. The system chipset features are listed below. 82xx Legacy Devices System Management Bus (SMB) Controller...
(Synchronous System Management Interrupt) 2.4.2 AMD Geode™ CS5536 ATA-6 Controller The single NOVA-LX IDE connector supports two ATA-6 HDDs. An ATA-6 (Ultra ATA/100) compliant IDE controller on the AMD Geode™ CS5536 has a maximum transfer rate of 100MB/s. ATA-6 includes advancements in error checking and ATA-6 drives are compatible with future interface additions.
NOVA-LX 5.25” Motherboard The onboard ATA-6 controller is able to support the following IDE HDDs: Ultra ATA/100, with data transfer rates up to 100MB/s Ultra ATA/66, with data transfer rates up to 66MB/s Ultra ATA/33, with data transfer rates up to 33MB/s...
NOVA-LX 5.25” Motherboard Figure 2-6: AC’97 Codec and Audio Connector The codec meets performance requirements for audio on PC99/2001 systems. Some of the codec features are listed below. Meets Microsoft WHQL/WLP 2.0 audio requirements 20-bit DAC and 18-bit ADC resolution 18-bit Stereo full-duplex CODEC with independent and variable sampling rate Complies with AC'97 2.3 specifications...
Page 38
NOVA-LX 5.25” Motherboard High quality differential CD input Two analog line-level mono input: PCBEEP, PHONE-IN Supports double sampling rate (96KHz) of DVD audio playback Two software selectable MIC inputs +6/12/20/30dB boost preamplifier for MIC input Stereo output with 6-bit volume control...
Figure 2-7: CompactFlash Connector 2.4.5 AMD Geode™ CS5536 USB Controller Four USB ports on the NOVA-LX board are interfaced to the chipset USB controller. Four USB 1.1 or USB 2.0 devices can be connected simultaneously to the NOVA-LX. The chipset USB controller has the following specifications: 4 USB ports USB 1.1 and USB 2.0 compliant...
NOVA-LX 5.25” Motherboard Figure 2-8: USB Connectors 2.4.6 AMD Geode™ CS5536 Serial Communications Eight high-speed UART serial port connectors, seven RS-232 and one that can be configured as RS-232, RS-422 or RS-485, are connected to the system chipset low pin count (LPC) port via the LPC bus.
NOVA-LX 5.25” Motherboard 2.4.8 BIOS The BIOS flash memory chip on the NOVA-LX has a licensed copy of AMI BIOS loaded onto it. The BIOS flash memory chip is connected to the chipset via the LPC bus. The flash BIOS features are listed below:...
NOVA-LX 5.25” Motherboard Figure 2-9: BIOS Chipset 2.5.3 Winbond W83627EHG Super I/O chipset The Winbond W83627HG Super I/O chipset is connected to the system chipset through the LPC bus. Page 22...
NOVA-LX 5.25” Motherboard Figure 2-10: Super I/O Chipset The Winbond W83627EHG is an LPC interface-based Super I/O device that comes with Environment Controller integration, floppy disk controller, and UART controller. Some of the features of the Winbond W83697EHG chipset are listed below: LPC Spec.
NOVA-LX 5.25” Motherboard 2.5.3.2 Super I/O Hardware Monitor Functions The Super I/O Hardware Monitor monitors internal voltages, system temperature and the cooling fan speed. All the monitored environmental parameters can be read from the BIOS Hardware Health Configuration menu. 2.5.3.3 Super I/O Parallel Port The Super I/O parallel port (LPT) is compatible with the following LPT specifications.
NOVA-LX 5.25” Motherboard 720K 1.2M 1.44M 2.88M Supported transfer rates 250Kbps 300Kbps 500Kbps 1Mbps 2Mbps 3-mode FDD and Win95/98 driver supported The FDD controller is interfaced to a FDD connected to the backplane through the board-to-board connectors. 2.5.3.5 Super I/O Keyboard and Mouse Controller The Super I/O keyboard and mouse controller is compatible with the following specifications.
2.5.4 Serial Port Chipset Two Fintek F81216DG chipsets on the NOVA-LX support six RS-232 serial ports and two RS-232/422/484 serial ports. The Fintek serial port chipset is interfaced to the southbridge chipset through the LPC bus.
NOVA-LX 5.25” Motherboard 2.6.2 PCI Bus Components The following components are interfaced through the PCI bus 2 x PCI Ethernet controllers 1 x PCI-to-ISA bridge 1 x PC/104-Plus interface 1 x Mini PCI slot 2.6.3 RealTek RTL8100C PCI Express Fast Ethernet Controller The PCI bus is interfaced to two RealTek RTL8100C Fast Ethernet controllers, which are then connected to two RJ-45 connectors.
NOVA-LX 5.25” Motherboard Figure 2-11: Ethernet Interface Some of the features of the Realtek RTL8100C are listed below: Supports PCI/mini-PCI interfaces Integrates Fast Ethernet MAC, physical chip, and transceiver onto a single chip 10Mbps and 100Mbps operation Supports 10Mbps and 100Mbps N-way auto-negotiation...
NOVA-LX 5.25” Motherboard Supports Full Duplex Flow Control (IEEE 802.3x) Provides interface to 93C46 EEPROM to store resource configuration and ID parameters Provides PCI clock run pin Provides LED pins for network operation status indication 2.5/3.3V power supply with 5V tolerant I/Os 2.6.4 ITE IT8888F PCI-to-ISA Bridge...
NOVA-LX 5.25” Motherboard Programmable PCI Address Decoders PC/PCI DMA Controller Distributed DMA Controller ISA Interface SM Bus Serial IRQ Supports NOGO function Single 33 MHz Clock Input +3.3V PCI I/F with +5V tolerant I/O buffers +5V ISA I/F and core Power Supply 2.6.5 PC/104-Plus Interface...
NOVA-LX 5.25” Motherboard Figure 2-13: PC/104-Plus Components 2.6.6 Mini PCI A Mini PCI slot on the board facilitates additional system expansion. Page 31...
Figure 2-14: Mini PCI Slot 2.7 Environmental and Power Specifications 2.7.1 System Monitoring Three thermal inputs on the NOVA-LX Super I/O Enhanced Hardware Monitor monitor the following temperatures: CPU Temperature Eight voltage inputs on the NOVA-LX Super I/O Enhanced Hardware Monitor monitor the...
2.7.3 Power Consumption Table 2-3 shows the power consumption parameters for the NOVA-LX running with a 500 MHz AMD Geode™ LX 800 processor with 256 MB of memory onboard. Voltage...
When the NOVA-LX is unpacked, please do the following: Follow the anti-static precautions outlined in Section 3.1. Make sure the packing box is facing upwards so the NOVA-LX does not fall out of the box. Make sure all the components shown in Section 3.3 are present.
If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the NOVA-LX from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw.
NOVA-LX 5.25” Motherboard Parallel port cable (P/N:19800-000049-RS) RS-422/485 cable with bracket (P/N: 19800-000063-RS) 4 COM (w bracket) (P/N: IO-KIT-4COM-R10) NOVA-LX-CE060 Windows CE 6.0 image and BSP S/W CD, licenses sticker (w/o CPU board) NOVA-LX-XPE Windows XPE image and BSP S/W CD,...
Figure 4-1 shows the on-board peripheral connectors, rear panel peripheral connectors and on-board jumpers. Figure 4-1: Connector and Jumper Locations 4.1.2 Peripheral Interface Connectors Table 4-1 shows a list of the peripheral interface connectors on the NOVA-LX. Detailed descriptions of these connectors can be found below. Page 40...
Page 61
NOVA-LX 5.25” Motherboard Connector Type Label ATX +12V power connector 4-pin ATX ATX power supply enable connector 3-pin wafer Audio CD In 4-pin header CN16 Audio connector 10-pin header CN15 Backlight inverter connector 5-pin wafer Battery connector 2-pin wafer Batter connector (LX800W models)
VGA connector 10-pin box header Table 4-1: Peripheral Interface Connectors 4.1.3 External Interface Panel Connectors Table 4-2 lists the rear panel connectors on the NOVA-LX. Detailed descriptions of these connectors can be found in Section 4.2.20 on page 65 Connector Type...
The ATX power supply enable connector enables the NOVA-LX to be connected to an ATX power supply. In default mode, the NOVA-LX can only us an AT power supply. To enable an ATX power supply the AT Power Select jumper must also be configured. Please refer to Chapter 3 for more details.
NOVA-LX 5.25” Motherboard Figure 4-4: Audio CD In Connector Pinouts (4-pin) PIN NO. DESCRIPTION CD Signal (Left) Ground Ground CD Signal (Right) Table 4-5: Audio CD In Connector Pinouts 4.2.4 Audio Connector (10-pin) CN Label: CN15 CN Type: 10-pin header...
4.2.5 Backlight Inverter Connector CN Label: 5-pin wafer (1x5) CN Type: CN Location: See Figure 4-6 CN Pinouts: See Table 4-7 The backlight inverter connector provides the backlight on the LCD display connected to the NOVA-LX with +12V of power. Page 46...
NOVA-LX 5.25” Motherboard READ DATA# SIDE 1 SELECT# DISK CHANGE# Table 4-9: 34-pin FDD Connector Pinouts 4.2.8 Front Panel Connector (8-pin) CN Label: CN14 14-pin header (2x7) CN Type: CN Location: See Figure 4-9 CN Pinouts: See Table 4-10 The front panel connector connects to external switches and indicators to monitor and controls the motherboard.
Table 4-11: GPIO Connector Pinouts 4.2.10 IDE Connector(40-pin) CN Label: CN10 CN Type: 40-pin header (2x20) CN Location: See Figure 4-11 See Table 4-12 CN Pinouts: One 40-pin IDE device connector on the NOVA-LX supports connectivity to two hard disk drives. Page 52...
NOVA-LX 5.25” Motherboard Figure 4-11: Secondary IDE Device Connector Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION RESET# GROUND DATA 7 DATA 8 DATA 6 DATA 9 DATA 5 DATA 10 DATA 4 DATA 11 DATA 3 DATA 12 DATA 2...
NOVA-LX 5.25” Motherboard I_SDA I_SCL LCD_VCC LCD_VCC LCD_VCC LCD_VCC Table 4-14: LVDS LCD Port Connector Pinouts 4.2.13 Parallel Port Connector CN Label: CN17 CN Type: 26-pin box header CN Location: See Figure 4-14 CN Pinouts: See Table 4-15 The 26-pin parallel port connector connects to a parallel port connector interface or some other parallel port device such as a printer.
NOVA-LX 5.25” Motherboard -12V Table 4-16: PC/104 Power Input Connector Pinouts 4.2.15 Serial Port Connectors (COM1, COM2) CN30 and CN31 CN Label: CN Type: 10-pin header (2x5) CN Location: See Figure 4-16 CN Pinouts: See Table 4-17 The four 10-pin serial port connectors provide four additional RS-232 serial communications channels.
NOVA-LX 5.25” Motherboard Receive Data (RXD) Request To Send (RTS) Transmit Data (TXD) Clear To Send (CTS) Data Terminal Ready (DTR) Ring Indicator (RI) Ground (GND) Ground (GND) Table 4-17: RS-232 COM Connector Pinouts 4.2.16 Serial Port Connector (COM3 and COM4)(RS-232, RS-422 or...
NOVA-LX 5.25” Motherboard Figure 4-17: RS-232/422/485 Serial Port Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION TXD485+ TXD485- RXD485+ RXD485- Table 4-18: RS-232/RS-485 Serial Port Connector Pinouts 4.2.17 Serial Port Connector (COM 5, COM 6, COM 7 and COM 8)
NOVA-LX 5.25” Motherboard The 40-pin serial port connector contains the following four serial ports, COM 5, COM 6, COM 7 and COM 8. All four serial ports are RS-232 serial communications channels. The serial port locations are specified below. COM 5 is located on pin 1 to pin 10...
NOVA-LX 5.25” Motherboard VSYNC LCD_EN HSYNC DISP_EN Table 4-20: TFT LCD TTL Port Connector Pinouts 4.2.19 USB Connectors (Internal) CN Label: CN12 and CN13 CN Type: 8-pin header (2x4) CN Location: See Figure 4-20 CN Pinouts: See Table 4-21 The 2x4 USB pin connectors each provide connectivity to two USB 1.1 or two USB 2.0 ports.
NOVA-LX 5.25” Motherboard PIN NO. DESCRIPTION PIN NO. DESCRIPTION DATAN- DATAM+ DATAN+ DATAN- Table 4-21: USB Port Connector Pinouts 4.2.20 VGA Connectors (Internal) CN Label: CN Type: 10-pin box header (2x4) CN Location: See Figure 4-21 CN Pinouts: See Table 4-22 The 2x5 VGA pin connector provides connectivity to an external VGA port enabling the system to be connected to a standard CRT screen.
Table 4-22: VGA Connector Pinouts 4.3 External Peripheral Interface Connectors The external peripheral interface connectors on the back panel are connected to devices externally when the NOVA-LX is installed in a chassis. The peripheral connectors on the rear panel are: 1 x Keyboard/mouse connector...
CN Pinouts: Table 4-24 The NOVA-LX is equipped with two built-in RJ-45 Ethernet controllers. The controllers can connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the connector indicating the status of LAN. The pin assignments are listed in the following...
NOVA-LX 5.25” Motherboard TXC+ TXD- Table 4-24: LAN Pinouts Figure 4-24: RJ-45 Ethernet Connector The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green LED indicates activity on the port and the yellow LED indicates the port is linked. See Table 4-25.
Electrostatic discharge (ESD) can cause serious damage to electronic components, including the NOVA-LX. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the NOVA-LX, or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
NOTE: The following installation notices and installation considerations should be read and understood before the NOVA-LX is installed. All installation notices pertaining to the installation of the NOVA-LX should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the NOVA-LX and injury to the person installing the motherboard.
NOVA-LX 5.25” Motherboard When working with the NOVA-LX, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system. Before and during the installation of the NOVA-LX DO NOT: Remove any of the stickers on the PCB board. These stickers are required for warranty validation.
When the NOVA-LX is unpacked, please do the following: Follow the anti-static precautions outlined in Section 5.1. Make sure the packing box is facing upwards so the NOVA-LX does not fall out of the box. Make sure all the components in the checklist shown in Chapter 3 are present.
The NOVA-LX can support both CF Type I cards and CF Type II cards. For the complete specifications of the supported CF cards please refer to Chapter 2. To install the a CF card (Type 1 or Type 2) onto the NOVA-LX, please follow the steps below: Step 1: Locate the CF card socket.
OPEN a jumper means removing the plastic clip from a jumper. Before the NOVA-LX is installed in the system, the jumpers must be set in accordance with the desired configuration. The jumpers on the NOVA-LX are listed in Table 5-1.
NOVA-LX 5.25” Motherboard Description Label Type AT or ATX power select 3-pin header CF card setup 3-pin header Clear CMOS 3-pin header COM 1/2 Pin 9 setting JP16 10-pin header COM 3 function select JP12 6-pin header COM 4 function select...
NOVA-LX 5.25” Motherboard The location of the AT or ATX Power Select jumper is shown in Figure 5-2 below. Figure 5-2: AT Power Select Jumper Location 5.5.2 AT or ATX Power Select Jumper Settings Jumper Label: Jumper Type: 23-pin header...
NOVA-LX 5.25” Motherboard Figure 5-3: AT Power Select Jumper Location 5.5.3 CF Card Setup Jumper Label: Jumper Type: 3-pin header Jumper Settings: See Table 5-4 Jumper Location: See Figure 5-4 The CF Card Setup jumper sets the CF Type I card or CF Type II cards as either the slave device or the master device.
Jumper Location: See Figure 5-5 If the NOVA-LX fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close pins 1 and 2 for a few seconds then remove the jumper cap and enable pins 1 and 2 to remain open.
NOVA-LX 5.25” Motherboard Short 4 – 6 COM 2 RI Pin use +5V Short 8 – 10 COM 2 RI Pin use RI Table 5-6: COM 1/2 Pin 9 Setting Jumper Settings The COM 1/2 Pin 9 Setting jumper location is shown in Figure 5-8 below.
NOVA-LX 5.25” Motherboard Short 5-6 RS-485 Table 5-7: COM 3/4 Function Select Jumper Settings The COM 3/4 Function Select jumper location is shown in Figure 5-7. Figure 5-7: COM 2 Function Select Jumper Location 5.5.7 LCD Clock Select Jumper Jumper Label:...
Figure 5-8: LCD Clock Select Jumper Location 5.5.8 LCD Voltage Selection WARNING: Permanent damage to the screen and NOVA-LX may occur if the wrong voltage is selected with this jumper. Please refer to the user guide that came with the monitor to select the correct voltage.
NOVA-LX 5.25” Motherboard LCD Voltage Select Description Short 1-2 +3.3V LVDS Default Short 2-3 +5V LVDS Table 5-9: LCD Voltage Selection Jumper Settings The LCD Voltage Selection jumper location. is shown in Figure 5-9. Figure 5-9: LCD Voltage Selection Jumper Location 5.5.9 PCI-104 Serial IRQ Selector...
NOVA-LX 5.25” Motherboard PCI-104 Serial IRQ Selector Description Open Disconnect Default Closed Connect Table 5-10: PCI-104 Serial IRQ Selector Jumper Settings The PCI-104 Voltage Setup jumper location is shown in Figure 5-11. Figure 5-10: PCI-104 Serial IRQ Selector Jumper Pinout Locations 5.5.10 PCI-104 Voltage Setup...
The NOVA-LX must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface. In a system with an individual power supply unit, the cooling fan of a power supply can also help generate airflow through the board surface.
IEI website (http://www.ieiworld.com.tw) to find out more about the available chassis. 5.7 Internal Peripheral Device Connections 5.7.1 Peripheral Device Cables The cables listed in Table 5-12 are shipped with the NOVA-LX. Quantity Type IDE Flat cable...
5.7.2 ATA Flat Cable Connection The ATA 66/100 flat cable connects to the NOVA-LX to one or two IDE devices. To connect an IDE HDD to the NOVA-LX please follow the instructions below.
Step 0: 5.7.3 Audio Kit Installation The Audio Kit that came with the NOVA-LX connects to the 10-pin audio connector on the NOVA-LX. The audio kit consists of three audio jacks. One audio jack, Mic In, connects to a microphone. The remaining two audio jacks, Line-In and Line-Out, connect to two speakers.
NOVA-LX 5.25” Motherboard 5.7.4 USB Cable (Dual Port without Bracket) The NOVA-LX is shipped with a dual port USB 2.0 cable. To connect the USB cable connector, please follow the steps below. Step 1: Locate the connectors. The locations of the USB connectors are shown in Chapter 3.
0: 5.7.5 FDD Cable Connection The FDD flat cable connects to the NOVA-LX to one FDD device. To connect an FDD to the NOVA-LX please follow the instructions below. Step 1: Locate the FDD connector.
Step 3: Insert the cable connectors. Once the cable connector is properly aligned with the 26-pin box-header connector on the NOVA-LX, connect the cable connector to the on-board connector. See Figure 5-16. Figure 5-16: LPT Cable Connection Step 4: Attach the LPT connector bracket to the chassis. The LPT cable connector is connected to a standard external LPT interface connector.
NOVA-LX 5.25” Motherboard Step 5: Connect LPT device. Once the LPT interface connector is connected to the chassis, the LPT device can be connected to the LPT interface connector. See Figure 5-17Step 0:\ Figure 5-17: Connect the LPT Device 5.7.7 Dual RS-232 Cable with Slot Bracket The dual RS-232 cable slot connector consists of two connectors attached to two independent cables.
NOVA-LX 5.25” Motherboard Figure 5-18: Dual RS-232 Cable Installation Step 3: Secure the bracket. The dual RS-232 connector has two D-sub 9 male connectors secured on a bracket. To secure the bracket to the chassis please refer to the reference material that came with the chassisStep 0: 5.7.8 Single RS-232/422/485 Cable with Slot Bracket...
The following external peripheral devices can be connected to the external peripheral interface connectors. RJ-45 Ethernet cable connectors PS/2 Y-cable To install these devices, connect the corresponding cable connector from the actual device to the corresponding NOVA-LX external peripheral interface connector making sure the pins are properly aligned. Page 95...
The NOVA-LX has a PS/2 connector on the external peripheral interface panel. The dual PS/2 connector is connected to the PS/2 Y-cable that came with the NOVA-LX. One of the PS/2 cables is connected to a keyboard and the other to a mouse to the system. Follow the steps below to connect a keyboard and mouse to the NOVA-LX.
NOVA-LX 5.25” Motherboard Step 1: Locate the dual PS/2 connector. The location of the PS/2 connector is shown in Chapter 3. Step 2: Insert the keyboard/mouse connector. Insert the PS/2 connector on the end of the PS/2 y-cable into the external PS/2 connector. See Figure 5-21.
NOVA-LX 5.25” Motherboard 6.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed.
NOVA-LX 5.25” Motherboard F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 6-1: BIOS Navigation Keys 6.1.3 Getting Help...
NOVA-LX 5.25” Motherboard 6.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. BIOS Menu 1: Main System Overview The System Overview lists a brief summary of different system components. The fields in System Overview cannot be changed.
NOVA-LX 5.25” Motherboard Processor: Displays auto-detected CPU specifications Type: Names the currently installed processor Speed: Lists the processor speed Count: The number of CPUs on the motherboard System Memory: Displays the auto-detected system memory. Size: Lists memory size The System Overview field also has two user configurable fields: System Time [xx:xx:xx] Use the System Time option to set the system time.
NOVA-LX 5.25” Motherboard Smbios Configuration (see Section 6.3.6) Remote Access Configuration (see Section 6.3.7) USB Configuration (see Section 6.3.7) IT888 Configuration (see Section ) Power Configuration (See Section ) BIOS Menu 2: Advanced 6.3.1 CPU Configuration Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications and configure the CPU.
NOVA-LX 5.25” Motherboard BIOS Menu 3: CPU Configuration The CPU Configuration menu (BIOS Menu 3) lists the following CPU details: Manufacturer: Lists the name of the CPU manufacturer Frequency: Lists the CPU processing speed FSB Speed: Lists the FSB speed...
NOVA-LX 5.25” Motherboard BIOS Menu 4: IDE Configuration OnBoard PCI IDE Controller [Both] Use the OnBoard PCI IDE Controller BIOS option to specify the IDE channels used by the onboard PCI IDE controller. The following configuration options are available. Disabled...
NOVA-LX 5.25” Motherboard Secondary Slave Both Allows the system to detect both the Primary and EFAULT Secondary IDE channels including the Primary Master, Primary Slave, Secondary Master and Secondary Slave. IDE Master and IDE Slave When entering setup, BIOS auto detects the presence of IDE devices. This displays the status of the auto detected IDE devices.
NOVA-LX 5.25” Motherboard BIOS Menu 5: IDE Master and IDE Slave Configuration Auto-Detected Drive Parameters The “grayed-out” items in the left frame are IDE disk drive parameters automatically detected from the firmware of the selected IDE disk drive. The drive parameters are listed as follows: Device: Lists the device type (e.g.
Page 128
NOVA-LX 5.25” Motherboard interrupt if block mode is not used. Block mode allows transfers of up to 64 KB per interrupt. PIO Mode: Indicates the PIO mode of the installed device. Async DMA: Indicates the highest Asynchronous DMA Mode that is supported.
Page 129
NOVA-LX 5.25” Motherboard LBA/Large Mode [Auto] Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the maximum drive capacity is 137 GB.
Page 130
NOVA-LX 5.25” Motherboard PIO mode 0 selected with a maximum transfer rate of 3.3MBps PIO mode 1 selected with a maximum transfer rate of 5.2MBps PIO mode 2 selected with a maximum transfer rate of 8.3MBps PIO mode 3 selected with a maximum transfer rate of 11.1MBps PIO mode 4 selected with a maximum transfer rate of 16.6MBps...
Page 131
NOVA-LX 5.25” Motherboard UDMA1 Ultra DMA mode 0 selected with a maximum data transfer rate of 16.6MBps Ultra DMA mode 1 selected with a maximum data transfer UDMA1 rate of 25MBps UDMA2 Ultra DMA mode 2 selected with a maximum data transfer rate of 33.3MBps...
NOVA-LX 5.25” Motherboard Disabled Prevents the BIOS from using 32-bit data transfers. Enabled Allows BIOS to use 32-bit data transfers on supported EFAULT hard disk drives. 6.3.3 Floppy Configuration Use the Floppy Configuration menu (BIOS Menu 6) to set or change the configurations for floppy disk drives.
NOVA-LX 5.25” Motherboard Disabled (default) 360 KB 5¼” 1.2 MB 5¼” 720 KB 3 ½” 1.44 MB 3½” 2.88 MB 3½” 6.3.4 Super IO Configuration Use the Super IO Configuration menu (BIOS Menu 7) to set or change the configurations for the FDD controllers, parallel ports and serial ports.
Page 134
NOVA-LX 5.25” Motherboard Parallel Address [378] The Parallel Port Address BIOS option assigns the I/O port address of the parallel port. The following address options are available: Disabled No I/O port address is assigned to the parallel port (Default) Parallel Port I/O port address is 378...
Page 135
NOVA-LX 5.25” Motherboard supports bi-directional communication between the system and the parallel port device and the transmission rates between the two are much faster than the Normal mode The parallel port becomes compatible with EPP devices described above Parallel Port IRQ [IRQ7] The Parallel Port Address BIOS option assigns the parallel port interrupt address.
Page 136
NOVA-LX 5.25” Motherboard Disabled No base address is assigned to Serial Port 2 2F8/IRQ3 Serial Port 2 I/O port address is 3F8 and the interrupt EFAULT address is IRQ3 3E8/IRQ4 Serial Port 2 I/O port address is 3E8 and the interrupt...
Page 137
NOVA-LX 5.25” Motherboard Disabled No base address is assigned to serial port 3 Serial port 4 I/O port address is 3E8 Serial port 4 I/O port address is 2E8 EFAULT Serial port 4 I/O port address is 2F0 Serial port 4 I/O port address is 2E0 Serial Port4 IRQ [10] Use the Serial Port4 IRQ option to select the interrupt address for serial port 4.
NOVA-LX 5.25” Motherboard Serial port 5 IRQ address is 10 Serial port 5 IRQ address is 11 EFAULT Serial Port6 Address [2D8] Use the Serial Port6 IRQ option to select the interrupt address for serial port 6. No base address is assigned to serial port 6...
NOVA-LX 5.25” Motherboard BIOS Menu 8: Hardware Health Configuration The following system parameters and values are shown. The system parameters that are monitored are: System Temperatures: The following system temperatures are monitored CPU Temperature Voltages: The following system voltages are monitored...
NOVA-LX 5.25” Motherboard 6.3.6 Smbios Use the Smbios Configuration menu (BIOS Menu 9) to configure SMBIOS parameters. BIOS Menu 9: Smbios Configuration Smbios Smi Support [Enabled] Use the Smbios Smi Support to enable the system to support the SMBIOS SMI wrapper for the PnP function 50h –...
NOVA-LX 5.25” Motherboard 6.3.7 Remote Access Configuration Use the Remote Access Configuration menu (BIOS Menu 10) to configure remote access parameters. The Remote Access Configuration is an AMIBIOS feature and allows a remote host running a terminal program to display and configure the BIOS settings.
Page 142
NOVA-LX 5.25” Motherboard Enabled Remote access configuration options shown below appear: Serial Port Number Serial Port Mode Flow Control Redirection after BIOS POST Terminal Type VT-UTF8 Combo Key Support Sredir Memory Display Delay These configuration options are discussed below. Serial Port Number [COM1] Use the Serial Port Number option to select the serial port used for remote access.
Page 143
NOVA-LX 5.25” Motherboard Base Address, IRQ [3F8h,4] The Base Address, IRQ option cannot be configured and only shows the interrupt address of the serial port listed above. Serial Port Mode [115200 8,n,1] Use the Serial Port Mode option to select baud rate through which the console redirection is made.
Page 144
NOVA-LX 5.25” Motherboard Disabled The console is not redirected after POST Boot Loader Redirection is active during POST and during Boot Loader Always Redirection is always active (Some OSes may not EFAULT work if set to Always) Terminal Type [ANSI] Use the Terminal Type BIOS option to specify the remote terminal type.
NOVA-LX 5.25” Motherboard No Delay EFAULT Delay 1 sec Delay 2 sec Delay 4 sec 6.3.8 USB Configuration Use the USB Configuration menu (BIOS Menu 11) to read USB configuration information and configure the USB settings. BIOS Menu 11: USB Configuration USB 1.1 Controller [Enabled]...
6.3.9 IT8888 Configuration Use the IT8888 Configuration menu (BIOS Menu 14) to access the Decode IO Spaces and Decode Memory Spaces configuration settings so that the system is compliant with the ISA card implemented on the NOVA-LX. Page 126...
Figure 6-1: IT8888 Configuration 6.3.9.1 ISA Decode IO Spaces NOTE: To set the correct settings in this section, please refer to the reference manual that came with the ISA card being implemented on the NOVA-LX. These settings must are user defined. Page 127...
NOVA-LX 5.25” Motherboard Figure 6-2: Decode IO Spaces Decode I/O Space n [Enabled] NOTE: Please refer to the reference material that came with the ISA card to ensure the correct configuration settings are made. Use the Decode I/O Space n option to enable the system to decode the nth space on the ISA card.
Page 149
NOVA-LX 5.25” Motherboard Disabled Decoding of the nth space is disabled Enabled Decoding of the nth space is enabled EFAULT I/O Decoding Speed NOTE: Please refer to the reference material that came with the ISA card to ensure the correct configuration settings are made.
128 Bytes 6.3.9.2 ISA Decode Memory Spaces NOTE: To set the correct settings in this section, please refer to the reference manual that came with the ISA card being implemented on the NOVA-LX. These settings must are user defined. Page 130...
NOVA-LX 5.25” Motherboard Figure 6-3: ISA Decode Memory Spacesk,l Decode Memory Space n [Enabled] NOTE: Please refer to the reference material that came with the ISA card to ensure the correct configuration settings are made. Use the Decode Memory Space n option to enable the system to decode the nth memory space on the ISA card.
Page 152
NOVA-LX 5.25” Motherboard Memory Decoding Speed NOTE: Please refer to the reference material that came with the ISA card to ensure the correct configuration settings are made. Use the Memory Decoding Speed option to specify the speed at which the nth memory space that must be decoded.
NOVA-LX 5.25” Motherboard 4 Bytes 8 Bytes 16 Bytes 32 Bytes 64 Bytes 128 Bytes 6.3.10 Power Use the Power menu (BIOS Menu 12) to access the Advanced Power Management (APM) menu. BIOS Menu 12: Power Configuration Power Supply Mode [ATX] Use the Power Supply Mode BIOS option to to select the power supply that is connected to the system.
NOVA-LX 5.25” Motherboard An AT power supply is connected to the system EFAULT An ATX power supply is connected to the system 6.3.10.1 APM Configuration Use the APM Configuration menu (BIOS Menu 13) to access set the APM configuration settings.
NOVA-LX 5.25” Motherboard 4 seconds to be turned off or it goes into a sleep state. 6.4 PCI/PnP Use the PCI/PnP menu (BIOS Menu 14) to configure advanced PCI and PnP settings. WARNING: Setting wrong values for the BIOS selections in the PCIPnP BIOS menu may cause the system to malfunction.
Page 156
NOVA-LX 5.25” Motherboard IRQ# [Available] Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral device. Available The specified IRQ is available to be used by EFAULT PCI/PnP devices Reserved The specified IRQ is reserved for use by Legacy ISA...
NOVA-LX 5.25” Motherboard DM Channel 1 DM Channel 3 DM Channel 5 DM Channel 6 DM Channel 7 Reserved Memory Size [Disabled] Use the Reserved Memory Size BIOS option to specify the amount of memory that should be reserved for legacy ISA devices.
NOVA-LX 5.25” Motherboard BIOS Menu 15: Boot 6.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 15) to configure advanced system boot options. Page 138...
NOVA-LX 5.25” Motherboard BIOS Menu 16: Boot Settings Configuration Quick Boot [Enabled] Use the Quick Boot BIOS option to make the computer speed up the boot process. Disabled No POST procedures are skipped Enabled Some POST procedures are skipped to decrease...
Page 160
NOVA-LX 5.25” Motherboard Enabled OEM Logo displayed instead of POST messages AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) messages to be displayed. The system forces third party BIOS to display...
NOVA-LX 5.25” Motherboard Disabled (Default) Cannot be booted from a remote system through the (Default) Can be booted from a remote system through the Enabled 6.5.2 Boot Device Priority Use the Boot Device Priority menu (BIOS Menu 17) to specify the boot sequence from the available devices.
NOVA-LX 5.25” Motherboard 6.5.3 Removable Drives Use the Removable Drives menu (BIOS Menu 18) to specify the boot sequence of the available FDDs. When the menu is opened, the FDDs connected to the system are listed as shown below: 1st Drive...
NOVA-LX 5.25” Motherboard BIOS Menu 18: Removable Drives 6.6 Security Use the Security menu (BIOS Menu 19) to set system and user passwords. Page 143...
NOVA-LX 5.25” Motherboard BIOS Menu 19: Security Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password. The default for this option is Not Installed. If a supervisor password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change Supervisor Password.
NOVA-LX 5.25” Motherboard Boot Sector Virus Protection [Disabled] Use the Boot Sector Virus Protection to enable or disable boot sector protection. Disabled Disables the boot sector virus protection EFAULT Enabled Enables the boot sector virus protection 6.7 Chipset Use the Chipset menu (BIOS Menu 20) to access the NorthBridge and SouthBridge...
NOVA-LX 5.25” Motherboard BIOS Menu 20: Chipset OnBoard AC97 Audio [Enabled] The OnBoard AC97 Audio option enables or disables the AC’97 CODEC. Disabled The onboard AC’97 is disabled Auto The onboard AC’97 automatically detected and enabled EFAULT 6.7.1 Video Configuration Use the Video Configuration menu (BIOS Menu 21) to configure the chipset settings on the chipset so that they comply with the display device connected to the system.
NOVA-LX 5.25” Motherboard BIOS Menu 21: Video Configuration Internal Graphics Memory [32] The Internal Graphic Memory option to specify the amount of internal memory is allocated to the graphics. Insert an EVEN number of MB in this entry between 2 and 254.
Page 168
NOVA-LX 5.25” Motherboard Flat Panel Type [640x480 18bit LVDS] Use the Flat Panel Type option to specify the flat panel PC type being used. The following options are available: LVDS Auto EFAULT Flat Panel Resolution Use the LCD Panel Resolution to specify the LCD panel resolution. Configuration options...
Page 169
NOVA-LX 5.25” Motherboard Flat Panel Refresh Rate NOTE: Please refer to the reference material that came with the flat panel to determine the correct configuration settings. Use the Flat Panel Refresh Rate to specify the refresh rate required by the panel.
NOVA-LX 5.25” Motherboard 6.8 Exit Use the Exit menu (BIOS Menu 22) to load default BIOS values, optimal failsafe values and to save configuration changes. BIOS Menu 22:Exit Save Changes and Exit Use the Save Changes and Exit option to save the changes made to the BIOS options and to exit the BIOS configuration setup program.
Page 171
NOVA-LX 5.25” Motherboard Discard Changes and Exit Use the Discard Changes and Exit option to exit the BIOS configuration setup program without saving the changes made to the system. Discard Changes Use the Discard Changes option to discard the changes and remain in the BIOS configuration setup program.
To install the drivers, please access the W . To do this, follow the INDOWS EVICE ANAGER instructions below. Step 1: Insert the CD into a CD drive of the system that contains the NOVA-LX. Step 2: Open W . (See Figure 7-1) INDOWS ONTROL ANEL...
NOVA-LX 5.25” Motherboard Figure 7-2: Performance and Maintenance Step 4: Double click the P option in Figure 7-2. ERFORMANCE AND AINTENANCE Step 5: The screen in Figure 7-3 appears. Figure 7-3: Access the System Step 6: Double click the S option in Figure 7-3.
NOVA-LX 5.25” Motherboard Step 7: The S screen in Figure 7-4 appears. YSTEM ROPERTIES Figure 7-4: System Properties Step 8: Double click the H tab in the Systems Property window Figure 7-4. ARDWARE Step 9: The screen in Figure 7-5 appears.
NOVA-LX 5.25” Motherboard Figure 7-6: Device Manager 7.3 VGA Driver Installation To install the VGA driver, please follow the instructions below. Step 1: Open the D . See Section 7.2. EVICE ANAGER Step 2: Right-click the VGA C (VGA C...
NOVA-LX 5.25” Motherboard Step 4: Select the U option in the small window shown in Figure 7-8. PDATE RIVER Step 5: The H in Figure 7-9 appears. ARDWARE PDATE IZARD Figure 7-9: Hardware Update Wizard Step 6: Make sure the driver CD is in the disk.
NOVA-LX 5.25” Motherboard Figure 7-10: VGA Driver Installation Start Step 9: Select the recommended option in Figure 7-10. Step 10: The Wizard then searches for the driver. See Figure 7-11. Page 161...
NOVA-LX 5.25” Motherboard Step 12: Click the Continue Anyway tab. Step 13: The Wizard updates the driver. See Figure 7-13. CAUTION: When the VGA driver is installed the system first sets a system restore point and backs up old files. This may take some time. Be patient and wait for the installation procedure to be completed.
NOVA-LX 5.25” Motherboard Figure 7-14: VGA Driver Installation Complete Step 15: Click the Finish tab in to complete the Figure 7-14 installation. Step 16: The Device Manager refreshes and the Graphics Driver can be seen in the Display adapters option. See Figure 7-15.
NOVA-LX 5.25” Motherboard Figure 7-15: Device Manager Update 7.4 Audio Driver Installation To install the Audio driver, please follow the instructions below. Step 1: Open the D . See Section 7.2. EVICE ANAGER Step 2: Right-click the M option listed under O...
NOVA-LX 5.25” Motherboard Step 4: Select the U option in the small window shown in Figure 7-17. PDATE RIVER Step 5: The H in Figure 7-18 appears. ARDWARE PDATE IZARD Figure 7-18: Hardware Update Wizard Step 6: Make sure the driver CD is in the disk.
NOVA-LX 5.25” Motherboard Figure 7-19: Audio Driver Installation Start Step 9: Select the recommended option in Figure 7-19. Step 10: The Wizard then searches for the driver. See Figure 7-20. Page 168...
NOVA-LX 5.25” Motherboard Step 12: Click the Continue Anyway tab. Step 13: The Wizard updates the driver. See Figure 7-22. CAUTION: When the Audio driver is installed the system first sets a system restore point and backs up old files. This may take some time. Be patient and wait for the installation procedure to be completed.
NOVA-LX 5.25” Motherboard Figure 7-23: Audio Driver Installation Complete Step 15: Click the Finish tab in to complete the Figure 7-23 installation. Step 16: The Device Manager refreshes and the Audio Driver can be seen in the Sound, Video and Game Controllers option. See Figure 7-24.
NOVA-LX 5.25” Motherboard Figure 7-24: Device Manager Update 7.5 LAN Driver To install the LAN driver, please follow the steps below. Step 1: Click LAN from the AMD LX/GX CD Driver Menu to open a window to the X:\LAN\Realtek (where X:\ is the system CD drive) folder on the driver CD.
NOVA-LX 5.25” Motherboard Step 4: Double click the Setup program icon in Figure 7-25. Step 5: The Install Shield Wizard is prepared to guide the user through the rest of the process (Figure 7-26). Figure 7-26: Preparing Setup Screen Step 6: Once initialized, the Install Wizard welcome screen appears (Figure 7-27).
NOVA-LX 5.25” Motherboard Figure 7-27: Install Wizard Welcome Screen Step 7: Click N to continue the installation or C to stop the installation. ANCEL Step 8: The Install Wizard starts to install the LAN driver. Step 9: Once the installation is complete, the InstallShield Wizard Complete screen appears (Figure 7-28).
Page 196
NOVA-LX 5.25” Motherboard The following is a list of the BIOS options that are available on this board. System Overview ....................101 System Time [xx:xx:xx] ..................102 System Date [xx/xx/xx] ..................102 OnBoard PCI IDE Controller [Both]..............105 IDE Master and IDE Slave..................106 Auto-Detected Drive Parameters................
Page 197
NOVA-LX 5.25” Motherboard Remote Access [Disabled].................. 121 Serial Port Number ....................122 Serial Port Mode....................122 Flow Control ......................122 Redirection after BIOS POST................122 Terminal Type ....................... 122 VT-UTF8 Combo Key Support ................122 Sredir Memory Display Delay ................122 Serial Port Number [COM1].................
Page 198
NOVA-LX 5.25” Motherboard Quick Boot [Enabled] ..................139 Quiet Boot [Disabled] ..................139 AddOn ROM Display Mode [Force BIOS] ............140 Bootup Num-Lock [On] ..................140 Boot From LAN Support [Disabled] ..............140 Change Supervisor Password................144 Change User Password..................144 Boot Sector Virus Protection [Disabled] ............
Page 200
NOVA-LX 5.25” Motherboard AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface.
Page 201
NOVA-LX 5.25” Motherboard Double Data Rate refers to a data bus transferring data on both the rising and falling edges of the clock signal. Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory.
Page 202
NOVA-LX 5.25” Motherboard IrDA Infrared Data Association (IrDA) specify infrared data transmission protocols used to enable electronic devices to wirelessly communicate with each other. L1 Cache The Level 1 Cache (L1 Cache) is a small memory cache built into the system processor.
Page 203
NOVA-LX 5.25” Motherboard when power is lost. RAM has very fast data transfer rates compared to other storage like hard drives. SATA Serial ATA (SATA) is a serial communications bus designed for data transfers between storage devices and the computer chipsets. The SATA bus has transfer speeds up to 1.5 Gbps and the SATA II bus has...
NOVA-LX 5.25” Motherboard C.1 DIO Interface Introduction The DIO connector on the NOVA-LX is interfaced to GIO ports on the Winbond chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices.
NOVA-LX 5.25” Motherboard C.3 Assembly Language Samples C.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O input functions is listed below. AX, 6F08H Sets the digital port as input Initiates the INT 15H BIOS call C.3.2 Enable the DIO Output Function...
Page 208
NOVA-LX 5.25” Motherboard NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash.
Page 209
NOVA-LX 5.25” Motherboard NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. Example program: ; INITIAL TIMER PERIOD COUNTER W_LOOP: AX, 6F02H ;setting the time-out value BL, 30 ;time-out value is 48 seconds ;...
The compatible items described here have been tested by the IEI R&D team and found to be compatible with the NOVA-LX F.1 Compatible Operating Systems The following operating systems have been successfully run on the NOVA-LX. Windows 2000 with Service Pack 4 Windows XP with Service Pack 2...
NOVA-LX 5.25” Motherboard G.1 Hazardous Material Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
Page 217
NOVA-LX 5.25” Motherboard Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Hg) (Cd) Chromium (Pb) Biphenyls Diphenyl Ethers (CR(VI)) (PBB) (PBDE) Housing Display Printed Circuit Board Metal Fasteners Cable Assembly Fan Assembly Power Supply...