Related Manuals for IEI Technology NOVA-7810
Summary of Contents for IEI Technology NOVA-7810
- Page 1 NOVA-7810 Intel Mobile CPU Embedded Board with 10/100Mbps Ethernet, VGA, Audio Version 1.0 User Manual Version 1.0 June 11, 2003...
- Page 2 ©Copyright 2003 by ICP Electronics Inc. All Rights Reserved.
- Page 3 Trademarks NOVA-7810 is a registered trademark of ICP Electronics Inc. IBM PC is a registered trademark of International Business Machines Corporation. Intel is a registered trademark of Intel Corporation. Award is a registered trademark of Award Software International, Inc.
-
Page 4: Table Of Contents
............... 6 Specifications................6 Package Contents ..............7 Installation ..............8 NOVA-7810 Layout ..............8 Clear CMOS Setup ..............10 Compact Flash Setting.............. 10 Audio Amplifier Selection ............10 LCD Panel Shift Clock/Panel VCC Selection ........11 COM Port RI and Voltage Selection ..........11 COM4 RS232/RS422 (485) Selection .......... - Page 5 Appendix E: How to Use VIDEO-IN Function ... 47 Appendix F: How to Use LCD-TYPE Function .... 49...
-
Page 6: Introduction
815E. This product is designed for system manufacturers, integrators, or VARs who want to build a low power consumption system. NOVA-7810 provides on-chip VGA of up to 1600 x 1200 resolution and LCD of up to 1024 x 768 resolution. -
Page 7: Package Contents
Intel Mobile P800 (800MHz) and 256MB SDRAM. • Operating Temperature: 0 ℃ ~60 ℃ . Package Contents In addition to this User's Manual, the NOVA-7810 package includes the following items: • NOVA-7810 Mobile CPU bases single board computer x 1 •... -
Page 8: Installation
Installation NOVA-7810 Layout Figure 1... - Page 9 Figure 2...
-
Page 10: Clear Cmos Setup
Clear CMOS Setup CMOS RAM stores the configuration data of the board. It is set by system BIOS. To clear CMOS RAM, close JP1 for about 3 seconds, and then open it again. • JP1: Clear CMOS Setup Description Keep CMOS Setup (Normal Operation) Clear CMOS Setup Compact Flash Setting... -
Page 11: Lcd Panel Shift Clock/Panel Vcc Selection
LCD Panel Shift Clock/Panel VCC Selection This jumper is for the setting of LCD panel shift clock mode and Panel power voltage. • JP7: LCD Panel Shift Clock Description Inverted Normal • JP7: Panel VCC Description +3.3V COM Port RI and Voltage Selection JP8 is setting COM3, 4 RI and Voltage. -
Page 12: Com4 Rs232/Rs422 (485) Selection
COM4 RS232/RS422 (485) Selection • JP9: Selection COM4 is RS232/RS422 (485) Description RS232 RS422/485... -
Page 13: Connection
Connection This chapter describes how to connect peripherals, switches and indicators to the NOVA-7810 board. The connectors on NOVA-7810 are listed in the following table: Label Description CDIN1 CD-IN Connector Parallel Port Connector IDE Connector SUS LED CN8, 11 Serial Port 1,2... -
Page 14: Floppy Disk Drive Connector
Floppy Disk Drive Connector NOVA-7810 board is equipped with a 34-pin daisy-chain driver connector cable. • CN24: FDD Connector Description Description GROUND REDUCE WRITE GROUND GROUND DS1# GROUND INDEX# GROUND MOTOR ENABLE A# GROUND DRIVE SELECT B# GROUND DRIVE SELECT A#... -
Page 15: Ultra Ata33/66/100 Ide Disk Drive Connector
HDC CS1# HDD ACTIVE# GROUND Parallel Port This port is usually connected to a printer. NOVA-7810 includes an on-board parallel port, and accessed through a 26-pin flat-cable connector CN1. Three modes—SPP, EPP and ECP are supported. • CN1: Parallel Port Connector... -
Page 16: Usb Port Connector
DATA 0+ GROUND DATA 0- DATA 0+ GROUND Serial Ports The NOVA-7810 offers four high speed NS16C550 compatible UARTs with Read/Receive 16 byte FIFO in each serial port. • CN8: D_SUB 9-PIN Connector Description DATA CARRIER DETECT (DCD) RECEIVE DATA (RXD) -
Page 17: Power Connector
DATA SET READY (DSR) REQUEST TO SEND (RTS) CLEAR TO SEND (CTS) RING INDICATOR (RI) TX+ (RS422/485) TX- (RS422/485) RX+ (RS422/485) RX- (RS422/485) Power Connector NOVA-7810 has one connector for power supply. • CN30: Power Supply Connector Description VCC12V GROUND GROUND VCC5V •... -
Page 18: Keyboard Connector
MOUSE CLOCK IrDA Infrared Interface Port NOVA-7810 is built in with an IrDA port that supports Serial Infrared (SIR) or Amplitude Shift Keyed IR (ASKIR) interface. To use the IrDA port, set SIR or ASKIR model in Peripheral Setup COM 2 of BIOS. -
Page 19: Audio Connectors
GROUND • CDIN1: CD-IN Description CD LEFT SIGNAL GROUND GROUND CD RIGHT SIGNAL 3.12 VGA Connector NOVA-7810 has a 15-pin VGA connector built in directly to your CRT monitor. • CON1: 15-pin Female Connector Description Description GREEN BLUE GROUND GROUND... -
Page 20: Lan Rj45 Connector
3.13 LAN RJ45 Connector NOVA-7810 is equipped with built-in one 10/100Mbps Ethernet Controller. You can connect it to your LAN through RJ45 LAN connector. The pin assignments are as below: • CN37: Intel 82562ET LAN RJ45 Connector Description Description 3.14 Compact Flash Connector—TYPE II NOVA-7810 supports one CompactFlash socket provided from IDE2. -
Page 21: External Switches And Indicators
RESET SW GND HDD LED+ HDD LED - 3.16 IEEE-1394 Connector NOVA-7810 is equipped with IEEE1394 controller (TI TSB43AA22). You can connect it to your 1394 device through CN21 36 connector. The pin assignments are as below: • CN21: 1394 Connector... -
Page 22: Cardbus/Pcmcia Connector
3.17 CardBus/PCMCIA Connector NOVA-7810 has a built-in CardBus/PCMCIA interface connector. • CN44: CardBus/PCMCIA Connector Description Description GROUND CE1# READY GROUND GROUND CD1# CE2# VS1# IORD# IOWR# VS2# RESET WAIT# INPACK# REG# BVD2 BVD1 CD2# GROUND GROUND GROUND... -
Page 23: Digital I/O
One of the characteristics of digital circuit is fast response to high or low signal. This kind of response is highly needed for industrial operating environment. NOVA-7810 is designed with 4-bit digital inputs and 4-bit digital outputs to maintain a quality performance in such environment. -
Page 24: Lcd Panel Connector
3.19 LCD Panel Connector NOVA-7810 provides a 2 x 25-pin connector for LCD flat panel interface. It supports TFT LCD panels at the following options: Video Display Type Resolution Example TFT VGA 640 x 480, 18 bits Toshiba LTM10C209H TFT SVGA... -
Page 25: Ami Bios Setup
AMI BIOS Setup Introduction This chapter discusses the Setup program built into the BIOS, which allows users to configure the system. This configuration is then stored in battery-backed CMOS RAM so that Setup information is retained when the power is off. Starting Setup The BIOS is immediately active when you turn on the computer. -
Page 26: Change Supervisor Password
Write the current settings to CMOS and exit. Exit Without Saving: Exit without saving the current settings. AMIBIOS HIFLEX SETUP UTILITY – VERSION 1.52 ©2001 American Megatrends, Inc. All Rights Reserved NOVA-7810 V 1.0 (02/11/2003) Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup... -
Page 27: Standard Cmos Setup Selections
Standard CMOS Setup Selections AMIBIOS SETUP – STANDARD CMOS SETUP ©2001 American Megatrends Inc. All Rights Reserved Date (mm/dd/yyyy): Tue Mar 19,2002 Base Memory: 639 KB Time (hh/mm/ss): 17:18:10 Extd Memory: 247 MB Floppy Drive A: Not Installed Floppy Drive B: Not Installed LBA Blk PIO 32Bit Type Size... -
Page 28: Boot Sector Virus Protection
Primary/Secondary Master/Slave 32Bit Mode This option enables Primary Master IDE 32-bit data transfers on the IDE data port. When disabled, 16-bit data transfer will be used by the BIOS. 32-bit data transfers can only be enabled if IDE prefetch mode is also enabled. Boot Sector Virus Protection When this option is enabled, AMIBIOS issues a warning when any program or virus issues a Disk Format command or attempts to write... - Page 29 Quick Boot When Quick Boot is selected, DRAM testing function will be disabled. 1st Boot Device This option sets the type of device for the first boot drives that the AMIBIOS attempts to boot from after AMIBIOS POST is completed. The settings are Disabled, IDE-0, IDE-1, IDE-2, IDE-3, Floppy, ARMD-FDD, ARMD-HDD, CDROM, and SCSI.
- Page 30 When this option is selected, Num Lock is turned off when the system is powered on. Users can use the arrow keys on both the numeric keypad and the keyboard. PS/2 Mouse Support When this option is enabled, BIOS supports a PS/2- type mouse. System Keyboard This option does not specify if a keyboard is attached to the computer.
- Page 31 C000, 16k Shadow The selections for this option are as below: - Enabled: The contents of the video ROM area from C0000h - C3FFFh are copied (shadowed) from the ROM to the RAM for faster execution. - Disabled: The contents of the video ROM are not copied to the RAM.
-
Page 32: Advanced Chipset Setup Selections
D800, 16k Shadow These options enable shadowing of the contents of the ROM area named in the option title. The settings are Enabled, Disabled, and Cached. The ROM area not used by ISA adapter cards will be allocated to PCI adapter cards. DC00, 16k Shadow These options enable shadowing of the contents of the ROM area named in the option title. - Page 33 CAS# Latency (SCLs) This option controls the latency between the SDRAM read command and the time when data becomes available. RAS to CAS delay (SCLKs) This option controls the latency between the SDRAM active command and the read/write command. SDRAM RAS# Precharge (SCLKs) This controls the idle clocks after issuing a pre-charged command to the SDRAM.
-
Page 34: Power Management Setup Selections
Power Management Setup Selections AMIBIOS SETUP – POWER MANAGEMENT SETUP © 2001 American Megatrends Inc. All Rights Reserved ACPI Aware O/S Available Options: Sleep State S1/POS > No USB KB/MS wakeup From S3 Disabled Power Management/APM Enabled Suspend Time Out Disabled Throttle Slow Clock Temperature 65℃/149℉... - Page 35 Keyboard & PS/2 Mouse Enabling this option allows the corresponding IRQ input to be monitored for entering or leaving the sleep state. FDC/LPT/COM Ports Enabling this option allows the corresponding IRQ input to be monitored for entering or leaving the sleep state. SB &...
- Page 36 Resume By Alarm When this option is enabled, system will wake up from soft off mode according to the time you set. Alarm Date To set the date for alarm Alarm Hour To set the hour for alarm Alarm Minute To set the minute for alarm Alarm Second To set the second for alarm...
-
Page 37: Pci / Plug And Play Setup Selections
PCI / Plug and Play Setup Selections AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP © 2001 American Megatrends, Inc. All Rights Reserved. Plug and Play Aware O/S Available Options: Clear NVRAM on Every Boot On Board Audio Controller Enabled >... - Page 38 Allocate IRQ to PCI VGA Set this option to Yes to allocate an IRQ to the VGA device on the PCI bus. The settings are Yes or No. PCI Slot1/2/3/4 IRQ Priority The option specifies IRQ priority for PCI device installed in PCI expansion slot.
-
Page 39: Peripheral Setup Selections
Peripheral Setup Selections AMIBIOS SETUP – PERIPHERAL SETUP ©2001 American Megatrends, Inc. All Rights Reserved OnBoard Serial Port C 3E8/COM3 Available Options: Serial Port C IRQ Disabled OnBoard Serial Port D 2E8/COM4 3F8/COM1 Serial Port D IRQ 2F8/COM2 OnBoard FDC Enabled >... - Page 40 Parallel Port Mode This option specifies the parallel port mode. The settings are Normal, Bi-Dir, EPP, or ECP. - Normal: The normal parallel port mode is used. - Bi-Dir: Use this setting to support bi-directional transfers on the parallel port. - EPP: The parallel port can be used with devices that adhere to the Enhanced Parallel Port (EPP) specification.
-
Page 41: Hardware Monitor Setup Selections
F1: Help F2/F3: Color Figure 8: Hardware Monitor Setup This setup helps users monitor the NOVA-7810 board on board system voltage and fan speed. The function is implemented by on board W83627HF chip. The voltage monitoring will cover V core, Vtt, +3.3V, SB5V, +5V and +12V. -
Page 42: Appendix A: Watchdog Timer
Appendix A: Watchdog Timer The Watchdog Timer is provided to ensure that standalone systems can always recover from CPU crash caused by external EMI or a software bug. When the CPU is not functioning normally, a hardware reset (cold boot) will be performed to bring the system to a normal state. -
Page 43: Appendix B: Digital I/O
One of the characteristics of digital circuit is fast response to high or low signal. This kind of response is highly needed for harsh and critical industrial operating environment. NOVA-7810 is designed with 4-bit digital inputs and 4-bit digital outputs to ensure a quality performance in such operating environment. -
Page 44: Appendix C: Address Mapping
Appendix C: Address Mapping IO Address Map I/O address Range Description 000-01F DMA Controller #1 020-021 Interrupt Controller #1, Master 02E-02F Super I/O 040-05F 8254 timer 04E-04F Super I/O 060-06F 8042 (Keyboard Controller) 070-07F Real time Clock, NMI Mask 080-09F DMA Page Register 0A0-0BF Interrupt Controller #2... -
Page 45: Dma Channel Assignments
IRQ Mapping Table IRQ0 System Timer IRQ8 RTC clock IRQ1 Keyboard IRQ9 Available IRQ2 Cascade to IRQ Controller IRQ10 COM4 IRQ3 COM2 IRQ11 COM3 IRQ4 COM1 IRQ12 PS/2 mouse IRQ5 Audio Device IRQ13 FPU IRQ6 IRQ14 Primary IDE IRQ7 Printer IRQ15 Secondary IDE DMA Channel Assignments Channel... -
Page 46: Appendix D: How To Use Wake-Up Function
Appendix D: How to Use Wake-Up Function NOVA-7810 provides two kinds of Wake up Function. Wake-Up function is enabled when you use ATX power supply. Wake-Up By Ring: You must enable the option Power On By Ring of CMOS SETUP. The ATX power supply will be switched on when there is a ring signal detected on pin “RI”... - Page 47 Appendix E: How to Use VIDEO-IN Function NOVA-7810 enables users to capture live video from video source such as the CCTV camera. NOVA-7810 has four video input channels for surveillance systems. Steps of driver installation: 1. Insert IEI Driver CD-ROM 2.
- Page 48 Pin Definition: Dupont Head 8Pin Description Description AVIN0 GROUND AVIN1 GROUND AVIN2 GROUND AVIN3 GROUND D-SUB 9Pin(for both cable 1 and cable 2) Description Description AVIN0 AVIN1 AVIN2 AVIN3 GROUND GROUND GROUND GROUND Cable 2: D-SUB 9Pin, connected to cable 1. RCA connectors are connected with video-in source.
- Page 49 Appendix F: How to Use LCD-TYPE Function NOVA-7810 provides four kinds of LCD-TYPE function. LCD-TYPE function setup procedure: 1. Go to the DOS command prompt in MS-DOS or Windows 9x 2. In DOS command prompt, type "LCD_Prg" 3. Select 1, 2, 3, or 4 from LCD Type 4.