IFM Electronic LK7 Operating Instructions Manual
IFM Electronic LK7 Operating Instructions Manual

IFM Electronic LK7 Operating Instructions Manual

Electronic level sensor

Advertisement

Quick Links

Operating instructions
Electronic level sensor
UK
LK7 / LK0

Advertisement

Table of Contents
loading

Summary of Contents for IFM Electronic LK7

  • Page 1 Operating instructions Electronic level sensor LK7 / LK0...
  • Page 2: Table Of Contents

    Contents 1 Menu structure �����������������������������������������������������������������������������������������������������3 2 Controls and visual indication ������������������������������������������������������������������������������4 3 Function and features ������������������������������������������������������������������������������������������4 3�1 Measuring range ��������������������������������������������������������������������������������������������5 3�2 Offset �������������������������������������������������������������������������������������������������������������5 3�3 Applications ���������������������������������������������������������������������������������������������������6 4 Operating modes �������������������������������������������������������������������������������������������������6 4�1 Run mode ������������������������������������������������������������������������������������������������������6 4�2 Display mode �������������������������������������������������������������������������������������������������6 4�3 Programming mode ���������������������������������������������������������������������������������������7 5 Installation������������������������������������������������������������������������������������������������������������7 5�1 Mounting elements ����������������������������������������������������������������������������������������7 5�2 Mounting recommendation ����������������������������������������������������������������������������7...
  • Page 3: Menu Structure

    1 Menu structure...
  • Page 4: Controls And Visual Indication

    2 Controls and visual indication Mode/Enter display of the level, LED display display of parameters and parameter values 2 x LED red switching status; lights if output I / II has switched Mode / Enter selection of the parameters and button acknowledgement of the parameter values setting of the parameter values...
  • Page 5: 3�1 Measuring Range

    3.1 Measuring range A = measured / display value LK0022 LK0023 LK0024 LK7022 LK7023 LK7024 inch inch inch L = probe length 26�4 10�4 47�2 18�6 72�8 28�7 A = active zone 19�5 7�7 39�0 15�4 58�5 23�0 I = inactive zone 5�3 2�0 5�3...
  • Page 6: 3�3 Applications

    3.3 Applications • The sensor continually monitors and adjusts to the medium� Thus it adapts itself to different media and compensates for changes in the medium� • For water and hydrous media with temperatures > 35°C install the unit into the climatic tube (order no�...
  • Page 7: 4�3 Programming Mode

    4.3 Programming mode Setting of the parameter values While viewing a parameter value pressing the "Set" button for more than 5 s causes the unit to enter the programming mode� You can alter the parameter value by pressing the "Set" button and confirm the new value by pressing the "Mode/Enter"...
  • Page 8: 5�3 Special Mounting Conditions

    5.3 Special mounting conditions • If possible, mount the unit in the middle of the vessel when it is installed in small plastic tanks: • For dirty media we recommend: Fasten the unit in a zone where there is much movement of the medium (e�g�...
  • Page 9: Electrical Connection

    6 Electrical connection The unit must only be connected by an electrician� The national and international regulations for the installation of electrical equipment must be observed� Voltage supply to EN50178, SELV, PELV� Disconnect power before connecting the unit� Wiring: p-switching (LK7xxx) n-switching (LK0xxx) 4: OUT1 4: OUT1...
  • Page 10: Programming

    7 Programming Press the Mode/Enter button several times until the respective parameter is Mode/Enter Set displayed� Press the Set button and keep it pressed� The current parameter value flashes Mode/Enter Set for 5 s, then the value is increased* (incremental by pressing briefly or scrolling by holding pressed)�...
  • Page 11: Installation And Set-Up / Operation

    8 Installation and set-up / operation After mounting, wiring and setting check whether the unit operates correctly� 8.1 Display during operation switch on, initialisation XXX / XX�X level indication; flashing: level close to the maximum measured value - - - level below the active zone SC1, SC2 flashing = short circuit in switching output 1 or 2...
  • Page 12: Technical Information / Functioning / Parameters

    9 Technical information / Functioning / Parameters 9.1 Adjustable parameters Switch-on point: Upper limit value at which the output changes its switching status, indicated in cm or inch� setting range inch in steps of LK0022 / LK7022 2�5 ��� 20�5 1�0 ���...
  • Page 13 Offset (basic value for display and measured value): The area between the bottom of the vessel and lower face of the measuring probe can be entered as offset value� Thus the display and switch points refer to the real vessel level� setting range inch in steps of...
  • Page 14: 9�2 Hysteresis (Hno, Hnc)

    9.2 Hysteresis (Hno, Hnc): The hysteresis keeps the switching state of the output stable if the level varies about the preset value� When the level is rising, the output switches when the switch-on point has been reached (SPx); when the level is falling again, the output switches back when the switch-off point (rPx) has been reached�...
  • Page 15: Technical Data

    10 Technical data Operating voltage [V] ������������������������������������������������������������������������������������������� 12���30 DC Current rating [mA] ��������������������������������������������������������������������������������������������������������� 200 Short-circuit protection; reverse polarity protection / overload protection Voltage drop [V] ������������������������������������������������������������������������������������������������������������ < 2�5 Current consumption [mA] ��������������������������������������������������������������������������������������������� < 80 Accuracy of switch point [% of value of measuring range] ���������������������������������������������� ± 5 Repeatability [% of value of measuring range �����������������������������������������������������������������...
  • Page 16: Scale Drawing

    11 Scale drawing 1 = 7-segment LED display 2 = programming buttons 3 = housing connection with cable lug for cable 1�5 - 2�5 mm LK0022 LK0023 LK0024 LK7022 LK7023 LK7024 inch inch inch L = probe length 26�4 10�4 47�2 18�6 72�8...
  • Page 17: Applications

    12 Applications 12.1 Hydraulic vessel Minimum level monitoring with prewarning and alarm Switching output 1: prewarning slightly above rP1 (to suppress wave movements) below preset level → prewarning, start refilling hysteresis function, normally closed (Hnc) Switching output 2: alarm min� value reached again → alarm reset below min�...
  • Page 18: 12�2 Pumping Station

    12.2 Pumping station Empty the vessel with overflow protection Switching output 1: control to empty vessel upper value exceeded → submersible pump ON lower value reached → submersible pump OFF hysteresis function, normally open (Hno) Switching output 2: overflow protection maximum value exceeded →...
  • Page 19: 12�3 Storage Vessel

    12.3 Storage vessel Monitoring of the acceptable range (alarm) and level control Switching output 1: refilling upper preset value reached → finish refilling below lower preset value → start refilling hysteresis function, normally closed (Hnc) Switching output 2: safety function min - max max�...

This manual is also suitable for:

Lk0

Table of Contents