Olivetti FS-529 Service Manual
  1. Manuals
  2. Brands
  3. Olivetti Manuals
  4. Printer
  5. FS-529
  6. Service manual
Olivetti FS-529 Service Manual

Olivetti FS-529 Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Option Printer
FS-529
SERVICE MANUAL
Code Y111310-1

Advertisement

Table of Contents
loading

Related Manuals for Olivetti FS-529

Summary of Contents for Olivetti FS-529

  • Page 1 Option Printer FS-529 SERVICE MANUAL Code Y111310-1...
  • Page 2 PUBLICATION ISSUED BY: Olivetti S.p.A. 77, Via Jervis - 10015 Ivrea (TO) Italy Copyright © 2009, Olivetti All rights reserved...

  • Page 3: Table Of Contents

    Field Service Ver. 1.0 Jul. 2009 CONTENTS FS-529 OUTLINE PRODUCT SPECIFICATIONS ................1 MAINTENANCE PERIODICAL MAINTENANCE PROCEDURE ............3 Paper exit section ....................3 2.1.1 Cleaning procedure for each parts..............3 OTHER MAINTENANCE ITEM ................4 Items not allowed to be disassembled and adjusted ..........4 Disassembly/reassembly parts list................

  • Page 4: Field Service Ver. 1.0 Jul

    Field Service Ver. 1.0 Jul. 2009 Blank Page...

  • Page 5: Outline

    Field Service Ver. 1.0 Jul. 2009 1. PRODUCT SPECIFICATIONS OUTLINE PRODUCT SPECIFICATIONS A. Type Type Multi staple finisher built into the main body Installation Installed in main body Document align- Center ment B. Functions Modes Sort, group, sort offset, group offset, sort staple C.
  • Page 6 1. PRODUCT SPECIFICATIONS Field Service Ver. 1.0 Jul. 2009 E. Stapling Letter S, A4S, 8- X 11S or less 50 sheets No. of sheets to be Legal, B4, 8- X 14 or greater 30 sheets stapled 60 to 90 g/m (16 to 24 lb): 48 sheets + 2 sheets (209 g/m (55.5 lb)) Back of the corner...

  • Page 7: Maintenance

    Field Service Ver. 1.0 Jul. 2009 2. PERIODICAL MAINTENANCE PROCEDURE MAINTENANCE PERIODICAL MAINTENANCE PROCEDURE Paper exit section NOTE • The alcohol described in the cleaning procedure of maintenance represents the isopropyl alcohol. 2.1.1 Cleaning procedure for each parts A. Periodically cleaning parts/cycle •...

  • Page 8: Other Maintenance Item

    3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 OTHER MAINTENANCE ITEM Items not allowed to be disassembled and adjusted A. Paint-locked screws NOTE • To prevent loose screws, a screw lock in blue or green series color is applied to the screws.

  • Page 9: Disassembly/Reassembly Parts List

    Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM Disassembly/reassembly parts list Section Part name Ref. page Front left cover Front right cover Exterior parts Upper cover Rear cover Finisher Conveyance roller unit Units Stapler unit P.10 Paper exit tray unit P.11 FS control board (FSCB) P.14...

  • Page 10: Disassembly/Reassembly Procedure

    3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 Disassembly/reassembly procedure 3.3.1 Front left cover 1. Remove the screw [1] and two tabs [2], and remove the front left cover [3]. A0U7F2C001DA 2. Reinstall the above parts following the removal steps in reverse. 3.3.2 Front right cover 1.

  • Page 11: Upper Cover

    Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM 3.3.3 Upper cover 1. Remove the front left cover. See P.6 2. Remove the rear cover. See P.8 3. Remove the screw [1], and remove the cover [2]. A0U7F2C003DA 4. Remove six screws [1], and remove the upper cover [2].

  • Page 12: Rear Cover

    3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 3.3.4 Rear cover 1. Remove three screws [1], and remove the rear cover [2]. A0U7F2C005DA 2. Reinstall the above parts following the removal steps in reverse. 3.3.5 Finisher 1. Remove the relay cord [1]. A0U7F2C501DA 2.

  • Page 13: Conveyance Roller Unit

    Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM 3. Remove three screws [1], and remove the rear left cover [2] of the main body. A0U7F2C007DA 4. Remove two screws [1], and remove the finisher [2]. A0U7F2C502DA 5. Reinstall the above parts following the removal steps in reverse. 3.3.6 Conveyance roller unit 1.

  • Page 14: Stapler Unit

    3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 3.3.7 Stapler unit 1. Remove the front right cover. See P.6 2. Remove the conveyance roller unit. See P.9 3. Move the stapler unit [1] to the marked position [2]. A0U7F2C009DA 4.

  • Page 15: Paper Exit Tray Unit

    Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM 6. Remove the screw [1], and remove the stapler cover plate [2]. 7. Disconnect two connectors [3]. 8. Remove the stapler unit [4]. A0U7F2C012DA 9. Reinstall the above parts following the removal steps in reverse. 3.3.8 Paper exit tray unit 1.
  • Page 16 3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 5. Remove two screws [1], and remove the exit roller cover [2]. A0U7F2C504DA 6. Remove four screws [1], and remove the plate [2]. A0U7F2C505DA 7. Remove the screw [1], and remove the rear sub cover [2].
  • Page 17 Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM 9. Turn the motor [1] in the direction shown by the arrow and raise the exit tray [2]. 10. Unhook two shutter tabs [3]. 11. Turn the motor [1] further and raise the exit tray [2].

  • Page 18: Fs Control Board (Fscb)

    3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 14. Remove the front shaft and remove the exit tray unit [1]. A0U7F2C511DA 15. Reinstall the above parts following the removal steps in reverse. 3.3.9 FS control board (FSCB) 1. Remove the rear cover. See P.8 2.

  • Page 19: Pick Up Roller Position Motor (M1)

    Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM 3.3.10 Pick up roller position motor (M1) 1. Remove the front left cover. See P.6 2. Disconnect the connector [1]. 3. Remove three screws [2], and remove the pick up roller position motor assy [3].

  • Page 20: Tray Up/Down Motor (M2)

    3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 3.3.11 Tray up/down motor (M2) 1. Remove the rear cover. See P.8 2. Remove the upper cover. See P.7 3. Remove the FS control board. See P.14 4. Remove the conveyance roller unit. See P.9 5.
  • Page 21 Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM 8. Remove four screws [1], and remove the tray up/down motor assy [2]. NOTE • When removing the tray up/down motor assy [2], the exit tray [3] bounces. Be sure to press the exit tray [3] down when removing the tray up/down motor assy [2].

  • Page 22: Conveyance Motor/1 (M5)

    3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 3.3.12 Conveyance motor/1 (M5) 1. Remove the rear cover. See P.8 2. Remove the conveyance roller unit. See P.9 3. Remove the FS control board. See P.14 4. Remove the harness guide. See P.27 5.

  • Page 23: Conveyance Motor/2 (M6)

    Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM 3.3.13 Conveyance motor/2 (M6) 1. Remove the rear cover. See P.8 2. Remove the conveyance roller unit. See P.9 3. Remove the flapper solenoid. See P.24 4. Remove the conveyance motor/1. See P.18 5.

  • Page 24: Stapler Movement Motor (M7)

    3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 3.3.14 Stapler movement motor (M7) 1. Remove the front left cover. See P.6 2. Remove the rear cover. See P.8 3. Remove the upper cover. See P.7 4. Remove the pick up roller position motor. See P.15 5.

  • Page 25: Fan Motor (Fm1)

    Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM 9. Remove the harness from the har- ness guide [1]. A0U7F2C026DA 10. Reinstall the above parts following the removal steps in reverse. 3.3.15 Fan motor (FM1) 1. Remove the front left cover. See P.6 2.
  • Page 26 3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 6. Remove the JAM processing dial [1]. 7. Remove the spring [2]. 8. Remove three screws [1], and remove the plate [4]. A0U7F2C028DA 9. Remove the C-ring [1], and remove two gears [2].

  • Page 27: Paddle Solenoid (Sd2)

    Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM 3.3.16 Paddle solenoid (SD2) 1. Remove the rear cover. See P.8 2. Remove the upper cover. See P.7 3. Remove the FS control board. See P.14 4. Remove the conveyance roller unit. See P.9 5.

  • Page 28: Flapper Solenoid (Sd4)

    3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 3.3.17 Flapper solenoid (SD4) 1. Remove the rear cover. See P.8 2. Remove the conveyance roller unit. See P.9 3. Remove three screws [1], and remove the rear rail [2]. A0U7F2C033DA 4.
  • Page 29 Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM A. Adjustment after installation 1. Remove the rear cover. See P.8 2. Remove the screw [1], and remove the cover [2]. A0U7F2C036DA 3. Illuminate the inside from the open- ing [1] shown in the illustration. 4.

  • Page 30: Belt Retract Solenoid (Sd5)

    3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 3.3.18 Belt retract solenoid (SD5) 1. Remove the front left cover. See P.6 2. Remove the spring [1], and remove the lever [2]. A0U7F2C039DA 3. Remove the harness from the wire saddle [1].

  • Page 31: Harness Guide

    Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM 3.3.19 Harness guide 1. Remove the rear cover. See P.8 2. Remove the FS control board. See P.14 3. Disconnect the connector [1]. 4. Remove the harness from two wire saddles [2]. 5.
  • Page 32 3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009 Blank Page Service Manual Y111310-1...
  • Page 33 UPDATING STATUS DATE UPDATED PAGES PAGES CODE 09/2009 EDITION Y111310-1...

Table of Contents