Astria Envy35xxx series Installation And Operation Instructions Manual

Signature series envy direct-vent gas fireplaces

Advertisement

P/N 900005-00 Rev. NC 02/2014
Ce manuel est disponible en francais, simplement
en faire la demande. Numéro de la pièce 900005-01.
P900005-00
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and shall be installed.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile
home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the
rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.
WARNING AVERTISSEMENT AVISO
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
WARNING: If the information in these
instructions is not followed exactly, a fire or
explosion may result causing property damage,
personal injury or death.
— Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier, call
the fire department.
— Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
Installation and Operation Instructions
Astria™ Signature Series Envy
Direct-Vent Gas Fireplaces
Models
Envy35xxx *
EnvyCD35xxx *
* "xxx" indicates unique model identifiers.
This manual covers all Astria™ Envy models.
Installateur : Laissez cette notice avec l'appareil.
Consommateur : Conservez cette notice pour consultation ultérieure.
Une barrière conçue pour réduire le risque de brûlure
par le hublot chaude est fournie avec l'appareil et doit
être installé.
UNE SURFACE VITRÉE CHAUDE PEUT
CAUSER DES BRÛLURES.
LAISSER REFROIDIR LA SURFACE VITRÉE
AVANT D'Y TOUCHER.
NE PERMETTEZ JAMAIS À UN ENFANT DE
TOUCHER LA SURFACE VITRÉE.
AVERTISSEMENT : Assurez-vous de bien suivre les
instructions données dans cette notice pour réduire au
minimum le risque d'incindie ou d'explosion ou pour éviter
tout dommage matériel, toute blessure ou la mort.
— Ne pas entreposer ni utilizer d'essence ni d'autres
vapeurs ou liquides inflammables dans le voisinage
de cet appareil ou de tout autre appareil.
— QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucan interrupteur. Ne pas vous
servir des téléphones se trouvant dans le bâtiment
où vous trouvez.
• Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions du
fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incindies.
— L'installation et l'entretien doivent être assurés par un
installateur ou un service d'entretien qualifié ou par le
fournisseur de gaz.
Envy40xxx *
Envy45xxx *
EnvyCD40xxx *
EnvyCD45xxx *
EL VIDRIO CALIENTE
CAUSARÁ QUEMADURAS.
USTED DEBE NUNCA TOCAR
EL VIDRIO CALIENTE.
LOS NIÑOS DEBEN NUNCA
TOCAR EL VIDRIO.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Envy35xxx series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Astria Envy35xxx series

  • Page 1 EnvyCD35xxx * EnvyCD40xxx * EnvyCD45xxx * * “xxx” indicates unique model identifiers. This manual covers all Astria™ Envy models. P900005-00 INSTALLER: Leave this manual with the appliance. Installateur : Laissez cette notice avec l’appareil. CONSUMER: Retain this manual for future reference.
  • Page 2 Innovative Hearth Products General Information Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Safety and Your La sécurité et Seguridad y su Fireplace votre foyer chimenea All parts of your Toutes les parties de votre ¡Todas las partes de la...
  • Page 3: Table Of Contents

    Innovative Hearth Products General Information Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Traditional Fireplace Contemporary Fireplace THANK YOU FOR YOUR PURCHASE. WE APPRECIATE YOUR bUSINESS! Please carefully read and follow all instructions in this manual. Pay special attention to all warnings and safety information.
  • Page 4: General Information

    Innovative Hearth Products General Information Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 GENERAL INFORMATION IMPORTANT SAFETY INFORMATION L’information de sûreté importante Información importante de seguridad WARNING AVERTISSEMENT ADVERTENCIA Do not operate appliance with the Ne pas utiliser l’appareil si le...
  • Page 5: Fireplace Installation, Operation, And Maintenance Notices

    Innovative Hearth Products General Information Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 FIREPLACE INSTALLATION, OPERATION, AND MAINTENANCE NOTICES DO NOT ATTEMPT TO ALTER OR MODIFY THE CONSTRUCTION OF THE APPLIANCE OR ITS COMPONENTS. ANY MODIFICATION OR ALTERATION MAY VOID THE WARRANTY, CERTIFICATION, AND LISTINGS OF THIS UNIT.
  • Page 6 Innovative Hearth Products General Information Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 WARNING Clothing or other flammable material should not be placed on or near the appliance. AVERTISSEMENT On ne devrait pas placer de vêtements ni d’autres matières inflammables sur l’appareil ni à proximité.
  • Page 7: Packaging

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 INSTALLATION PACKAGING All models include The assembled vented gas fireplace heater is packaged with: • Literature Kit (Envelope containing Installation and Operation Instructions [this manual] and Safety-In-Operation Warning Labels) •...
  • Page 8: Btu Input

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 bTU Input Table 1: Input Rate, Gas Valves Input Rate (bTU/HR) Models Natural Gas Propane Gas 35” Traditional 35,500 high, 15,500 low 35,000 high, 18,000 low 35” Contemporary...
  • Page 9: Requirements For The Commonwealth Of Massachusetts

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Orifice Sizes—Sea Level to High Altitude These fireplaces are tested and approved for installation at elevations of 0–4500 ft (0–1372 m) above sea level using the standard burner orifice sizes (Table 4). For elevations above 4500 ft, contact your gas supplier or qualified service technician.
  • Page 10: Manufactured Home Requirements

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 MANUFACTURED HOME REQUIREMENTS This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by local codes. Cet appareil peut être installé dans une maison préfabriquée (mobile) déjà installée à demeure si les règlements locaux le permettent.
  • Page 11: Vent Termination Clearances

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 VENT TERMINATION CLEARANCES These instructions should be used as a guideline and do not supersede local codes in any way. Install venting according to local codes, these instructions, the current National Fuel Gas Code (ANSI Z223.1/NFPA 54) in the USA or the current standards of CAN/CGA-b149.1 in Canada.
  • Page 12 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Table 6: Horizontal vent termination clearances for buildings with combustible and noncumbustible exteriors Inside Corner Outside Corner Recessed Location See Table 5 Fixed Balcony with No Side Wall...
  • Page 13: Minimum Clearances To Combustibles

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 MINIMUM CLEARANCES TO COMbUSTIbLES Fireplace And Vent Clearances The fireplace is approved with zero clearance to combustible materials on all sides (Table 7), with the following exception: The unit may not be recessed (allowance made for mantel legs / side trim in Figure 5). When the unit is installed with one side flush with a wall, the wall on the other side of the unit must not extend beyond the front edge of the unit (Figure 5).
  • Page 14: Wall Finishes / Surrounds / Mantels

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Figure 5: Combustible Side Clearances Figure 6: Mantel Height At 14 1/2” minimum side wall At 13 3/4” At 5 1/2” clearance, a side wall 28 (711)
  • Page 15: Installation Sequence

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 INSTALLATION SEQUENCE The typical sequence of installation is outlined below; however, each installation is unique and may result in variations to the steps described. See the pages referenced in the following steps for detailed instructions.
  • Page 16 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Table 9: Fireplace Framing Specifications Framing should Model be constructed 39.75” 45.25” 24.0” 46.75” Vent Framing— 35” 10 1/2 of 2x4 or larger 1010 mm 1149 mm...
  • Page 17: Route The Gas Supply Line To The Fireplace

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Prepare the Fireplace Top Standoffs 1. Bend each of the two (2) L-shaped standoff components, at the designated places, into a U-shape (Figure 8). 2. Align the closed end of each U-shaped standoff component with the left/right side of the top, front of the fireplace and the attachement holes in the top of the fireplace (Figure 8).
  • Page 18 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 • A pipe joint compound rated for gas should be used on the threaded joints. Ensure propane-resistant compounds are used in propane applications. Be very careful that the pipe compound does not get inside the pipe.
  • Page 19 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 VENT SYSTEM PREPARATION Select a Horizontal or Vertical Vent System 1. With the fireplace secured in the framing, determine the vent route and identify the exterior termination location.
  • Page 20 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Table 13: Effective Vent Length Model Effective Length SV4.5L6 4 1/2” SV4.5L12 10 1/2” SV4.5L24 22 1/2” SV4.5L36 34 1/2” SV4.5L48 46 1/2” SV4.5LA 1 1/2–7” Connecting the vent pipe Secure Vent SV4.5 direct-vent system components are unitized concentric pipe components featuring positive twist...
  • Page 21 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Table 14: Vent Section Length Nominal Section Nominal Section Length Length (in.) (in.) Net Section Length 10.5 22.5 34.5 46.5 Net Section Length (in.) 10.5 22.5 34.5 46.5...
  • Page 22: Install The Vent System

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Install the Vent System Install the Vertical Termination Vent System These instructions should be used as a guideline and do not supersede local codes in any way. Install venting according to local codes, these instructions, the current National Fuel Gas Code (ANSI-Z223.1) in the USA or the...
  • Page 23 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Vertical (Offset) Installation 1. Analyze the vent route—Determine the number of vent sections (Table 13) and elbows (Figure 16) required. 2. Frame the ceiling opening—Use a plumb line from the ceiling above the fireplace to locate the center of the vertical run.
  • Page 24 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 8. Change vent direction of horizontal/inclined run—Install the SV4.5E45 and SV4.5E90 elbows in the same manner as the straight vent sections. See Vent elbows on Page 20 for more information.
  • Page 25 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Vertical Vent Figures/Tables NOTE: Secure Vent rigid vent pipe is shown in the figures; Secure Flex flexible vent pipe may also be used. ® ® NOTE: Rise per foot run ratios are acceptable all the way to level. For best results, maintain the horizontal/inclined run in a straight (no dips), slightly elevated plane of approximately 1/4”...
  • Page 26 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Install the Horizontal Termination Vent System These instructions should be used as a guideline and do not supersede local codes in any way. Install venting according to local codes, these instructions, the current National Fuel Gas Code (ANSI-Z223.1) in the USA or the current standards of CAN/CGA-B149.1 in Canada.
  • Page 27 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 10. Continue installation of horizontal/inclined sections—Continue with the installation of the straight vent sections in horizontal/inclined run. Install support straps every 5 ft. (1.52 m) along horizontal/inclined vent runs using conventional plumber’s tape (Figure 23).
  • Page 28 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Figure 24: Installing the Horizontal Termination Firestop/Spacer (SV4.5HF) shown Typical Termination on the exterior side of the wall. It Shown may also be installed on the interior side.
  • Page 29 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Horizontal Vent Figures/Tables NOTE: Secure Vent rigid vent pipe and terminal are shown in the figures. Secure Flex flexible vent pipe and ® ® terminal may also be used.
  • Page 30 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Table 20: Top Vent—Two 90° Elbows H + H Maximum V Minimum Wall firestop/spacer Wall Firestop/Spacer SV4.5HF ** (SV4.5HF) feet meters feet meters 0.91 0.490 1.58 0.914 2.07...
  • Page 31 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Vertical or Horizontal Venting Using Secure Flex Kits and Components Secure Flex venting kits and components may be used in any other vent installation where rigid Secure Vent (SV4.5)
  • Page 32: Complete The Field Wiring

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 e. Slide the gear clamp down and tighten it fully to secure the flexible vent to the adaptor outer collar approximately 3/4” from the end of the flexible vent.
  • Page 33 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Figure 28: Wiring Diagram—Electronic Gas Valves Figure 29: Wiring Diagram—Junction Box IPI Pilot Green Ground - Green Flame Sensor White Neutral - White Schematic Representation Only Spark Electrode...
  • Page 34 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Initialize the remote control system After completing fireplace installation, initialize the remote control system before operating the fireplace. 1. Insert the three (3) provided AAA batteries into the battery bay in the transmitter. Correctly align polarity (+/–).
  • Page 35: Connect The Gas Line

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Connect the Gas Line All codes require a shutoff valve mounted in the supply line. The shutoff valve should be oriented to face the fireplace front. The flex-line method is acceptable in the U.S.A. where local codes permit it. In the Commonwealth of Massachusetts, installation must be performed by a licensed plumber or gas fitter.
  • Page 36: Verify Proper Fireplace Operation

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Test Factory and Field Connections for Gas Leaks WARNING Never use an open flame to check for leaks. 1. Turn ON the gas supply and test for gas leaks, using a gas leak test solution—also known as bubble leak solution.
  • Page 37 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 CAUTION • Soot will be produced if the air shutter is closed too much. Any damage due to sooting, resulting from improperly setting the air shutter, is not covered under the warranty.
  • Page 38: Install The Finishing Materials

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Figure 36: Traditional Fireplaces Flame Appearance Figure 37: Contemporary Fireplaces Flame Appearance Table 23: Main Burner Shutter Opening—Factory Setting Models Natural Gas Propane 35” 3/16” (4.8 mm) 7/16”...
  • Page 39: Attach The Safety-In-Operation Warning Labels

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 NOTE: The integrated finish trim is adjustable to accommodate a wall thickness of an additional 1” (25 mm)—for a 2” (51 mm) total thickness. NOTE: For wall thicknesses greater than 2” (51 mm), remove the three integrated finish trim pieces (Figure 39).
  • Page 40 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Attach the Safety-in-Operation Warnings NOTE: It is the installer’s responsibility to ensure these warnings are properly affixed during installation. These warning labels are a critical step in informing consumers of safe operation of this appliance.
  • Page 41: Installation Accessories

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 INSTALLATION ACCESSORIES Table 24: Listed Secure Vent™ Components Catalog Catalog Models Description Models Description Number Number Horizontal square termination Chase top shroud kit, arch top, H1968 SV4.5HT-2...
  • Page 42: Gas Conversion Kits

    Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 GAS CONVERSION KITS WARNING This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion, or the production of carbon monoxide may result;...
  • Page 43 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Installing Gas Conversion Kits WARNING The gas supply shall be shut OFF prior to disconnecting the electrical power, before proceeding with the conversion. AVERTISSEMENT Avant d’effecteur la conversion, coupez d’abord l’alimentation en gaz, ensuite, coupez l’alimentation electrique.
  • Page 44 Innovative Hearth Products Installation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Figure 43: Millivolt Pilot Figure 44: Orifice Pilot Pilot Orifice Orifice 12. Use pipe joint compound or Teflon tape on all pipe fittings before installing. ® NOTE: Ensure propane resistant compounds are used in propane applications, do not use pipe joint compounds on flare fittings.
  • Page 45: Operation

    Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 OPERATION WARNING Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house.
  • Page 46 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 ATTACH THE SAFETY-IN-OPERATION WARNINGS NOTE: It is the installer’s responsibility to ensure these warnings are properly affixed during installation. These warning labels are a critical step in informing consumers of safe operation of this appliance.
  • Page 47 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 burn-in Period The first few times this fireplace is operated, there will be an odor from the curing of paint and the burning off of the lubricants used in the manufacturing process. Depending on usage, the burn-in period may take a few hours or a few days.
  • Page 48 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Remote Control System WARNING Fire hazard. Can cause severe injury or death. The receiver causes ignition of the appliance. The appliance can turn on suddenly. Keep away from the appliance burner when operating the remote system or activating manual bypass of the remote system.
  • Page 49 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Turn ON the appliance 1. Press the ON/OFF key on the transmitter. 2. The transmitter display will show all active Icons on the screen. At the same time, the receiver will connect the thermopile to the gas valve millivolt coil and the appliance main burner will turn on.
  • Page 50 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Manual bypass of the remote control system If the batteries of the wall switch or transmitter are low or depleted, the appliance can be turned on manually.
  • Page 51 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Installing the logs and volcanic stone WARNING • Turn OFF all gas and electricity to the appliance before installing the volcanic stone and logs. • Do NOT install the logs until the appliance has been competely installed, the gas line connected and tested for leaks, and the initial burner operation has been confirmed.
  • Page 52 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 NOTE: Do not cover the burner ports. 1. If necessary, remove the glass door (Page 53). 2. Place Log 1 on the burner as shown (Figure 51).
  • Page 53 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Installing and removing the glass door WARNING • Do not attempt to substitute the materials used on these doors, or replace cracked or broken glass. • Handle this glass with extreme care! Glass is susceptible to damage—Do not scratch or handle roughly while reinstalling the glass door frame.
  • Page 54 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Installing the glass door 1. Visually inspect the gasket on the backside of the glass door. NOTE: The gasket surface must be clean, free of irregularities, and seated firmly. Ensure it is properly located.
  • Page 55: Maintenance

    Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 MAINTENANCE Refer to the Maintenance Schedule on Page 58 for maintenance tasks, procedures, frequency, and a listing of by whom the tasks should be performed. Always verify proper fireplace operation after servicing.
  • Page 56 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Cleaning the glass door CAUTION Do not use abrasive cleaners on glass. Never clean the glass when it is hot. Clean the glass during the burn-in Period, and then only when necessary and when the fireplace is cool. Wipe the surface with a clean, dampened, soft cloth.
  • Page 57 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Inspecting the wiring Refer to the wiring diagram (Page 33). CAUTION When servicing controls, label all wires prior to disconnection. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
  • Page 58 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 MAINTENANCE SCHEDULE See the tables below for detailed information about required maintenance, both regular and annual. Table 30: Maintenance Performed Annually—Before the Burning Season Maintenance Task Performed by...
  • Page 59: Accessory Components

    Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 ACCESSORY COMPONENTS Touch-Up Paint Kit Repair of minor scratches and discoloration of the fireplace black painted surfaces may be accomplished with the touch-up paint kit. Table 32: Touch-Up Paint Kit Catalog No.
  • Page 60: Lighting Instructions

    Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 LIGHTING INSTRUCTIONS Electronic Gas Valve FOR YOUR SAFETY READ bEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result, causing property damage, personal injury, or loss of life.
  • Page 61 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 POUR PLUS DE SÉCURITÉ, LIRE AVANT DE METTRE EN MARCHE AVERTISSEMENT : Quiconque ne respecte pas à la lettre les instructions dans la présente notice risque de déclencher un incendie ou une explosion entraînant des dommages, des blessures ou la mort.
  • Page 62: Troubleshooting

    Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 TROUbLESHOOTING Before troubleshooting, ensure that the fireplace main line gas shutoff valve and the wall switch are in the ON position. The following troubleshoots the fireplace only to an elementary level. For detailed remote and ignition system troubleshooting, refer to the instructions provided with the remote.
  • Page 63: Replacement Parts

    Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 REPLACEMENT PARTS Table 36: Installer Replacement Parts Description Catalog Number Catalog Number Catalog Number Electronic Pilot Assembly, Natural Gas H7268 H7268 H7268 Flex Hose Connector, 24 in.
  • Page 64 Innovative Hearth Products Operation Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 WARNING Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.
  • Page 65: Warranty

    THE WARRANTY Innovative Hearth Products (“IHP”) Limited Lifetime Warranty warrants your Astria™ brand gas fireplace (“Product”) to be free from defects in materials and workmanship at the time of manufacture. The Product body and firebox carry the Limited Lifetime Warranty. Ceramic glass carries the Limited Lifetime Warranty against thermal breakage only.
  • Page 66 Innovative Hearth Products Installation and Operation Instructions Astria™ Signature Series Envy Direct-Vent Gas Fireplaces 900005-00, 02/2014 Contact an IHP dealer to obtain any of these parts. Please contact IHP for the phone number of your nearest IHP dealer. www.Astria.us.com Record the following important information about your fireplace:...

Table of Contents