Table of Contents
Advertisement
Quick Links
CUSTOMER
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
SUPPORT
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
INFORMATION
Web site: www.blackbox.com • E-mail: info@blackbox.com
ServTray
OCTOBER 2004
KVT201A
RMB3
KVT202A
RMB4
RMB1
RMB5
RMB2
Advertisement
Table of Contents
Related Manuals for Black Box ServTray KVT201A
Summary of Contents for Black Box ServTray KVT201A
- Page 1 Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 SUPPORT Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 INFORMATION Web site: www.blackbox.com • E-mail: info@blackbox.com...
- Page 2 FCC AND IC RFI STATEMENTS FEDERAL COMMUNICATIONS COMMISSION and INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS Class B Digital Device. This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 3 SERVTRAY INSTRUCCIONES DE SEGURIDAD (Normas Oficiales Mexicanas Electrical Safety Statement) 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura. 3.
- Page 4 TRADEMARKS USED IN THIS MANUAL TRADEMARKS USED IN THIS MANUAL ServSwitch is a trademark of Black Box Corporation. Centronics is a registered trademark of Centronics Corporation. PS/2 is a registered trademark of International Business Machines Corporation. UL is a registered trademark of Underwriters Laboratories Inc.
-
Page 5: Table Of Contents
Calling Black Box........ -
Page 6: Specifications
Input Signal: KVT201A: RGB analog, H/V separate; KVT202A: Even/Odd R/G/B data, sync signal, clock Plug-n-Play VESA: VESA DDC 1/2B Viewing Angle: KVT201A: -60 to +60 (H), -55 to +45 (V) typical; KVT202A: -80 to +80 (H), -80 to +80 (V) typical Backlight Unit: KVT201A: 2 CCFLs edge-light (top/bottom); KVT202A: 4 CCFLs edge-light (top/bottom) Temperature: Operating: 32 to 122°F (0 to 50°C);... -
Page 7: Introduction
LCD panel, and KVM module housed in an industry-standard 19" 1U-height rack drawer (see Figure 2-1). Two models are available: the ServTray with a 15" LCD panel (KVT201A) and the ServTray with a 17" LCD panel (KVT202A). Both models feature a full 105-key, low-profile, sturdy keyboard and touch pad with an ergonomically designed hand rest. - Page 8 CHAPTER 2: Introduction Accessories that you will need to purchase include: • 12-24 or 10-32 nuts/bolts • Rear Bracket Extension Kit (RMB1–RMB5): These kits contains two rear brackets, two extensions, and two end rails. Make sure you have the correct kit to fit the depth of your cabinet (see below). NOTE The following length is the depth measured between the front pole and rear pole inside a rack cabinet, not the outside depth of a rack cabinet enclosure.
-
Page 9: Installation
SERVTRAY 3. Installation 1. Choose a proper position in the cabinet for the rack drawer. Using 10-32 or 12-24 hardware (not included), mount the rear brackets (from the Rear Bracket Extension Kit, purchased separately) and lightly fasten them onto the rear vertical poles. (See Figure 3-1.) Both rear brackets will be removed later. Rear bracket Rear bracket Rear vertical... - Page 10 CHAPTER 3: Installation 3. Slide the console drawer into the rack cabinet from the front. Then insert the console drawer’s two slide rails into the rear brackets’ pockets. See Figure 3-3. Slide rail Rear Slide rail bracket Rear pocket bracket Figure 3-3.
- Page 11 SERVTRAY 5. Remove both of the loosely connected rear brackets and slide the console drawer out halfway to balance its weight. (See Figure 3-5.) The front brackets are now supporting the console drawer. Vertical rail Vertical rail Console drawer Rear bracket removed Rear bracket...
- Page 12 CHAPTER 3: Installation 8. Push the rear brackets all the way in and fasten them. 9. Slide out the console drawer. Push the KVM module evenly toward the drawer and secure both units using the thumbscrews. See Figure 3-7. Thumbscrews KVM module Console drawer Figure 3-7.
- Page 13 SERVTRAY 13. Once the ServTray is installed in the rack cabinet, you can connect it to a computer. The KVM module’s connectors attach to the KVM connectors on a PS/2 CPU via the CPU Cable shown in Figure 3-9. CPU Cable (EHN408-0010) This cable attaches to the Using the gender changer,...
-
Page 14: Operation
CHAPTER 4: Operation 4. Operation Once the ServTray is installed and connected to a PS/2 CPU or ServSwitch, it’s ready for operation. Control the unit via the buttons on the LCD panel (labeled 1 and 2 in Figure 4-1) and the LCD panel power switch (labeled 3 in Figure 4-1). -
Page 15: Troubleshooting
• Package it carefully. We recommend that you use the original container. • If you are shipping the ServTray for repair, make sure you include everything that came in the original package. Before you ship, contact Black Box to get a Return Authorization (RA) number. - Page 16 © Copyright 2004. Black Box Corporation. All rights reserved. 1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746...