Do you have a question about the Ceiling mounted utility heater and is the answer not in the manual?
Questions and answers
Jimmy Hester
May 10, 2025
HOW DO I ATTACH THE CORD TO THE WHEEL THAT CHANGES THE MODE, HIGH, LOW OR LIGHT? NEEDED TO ADD MODEL NO ... HQ1500
1 comments:
Mr. Anderson
May 20, 2025
To attach the cord to the mode-change wheel on the ProFusion HQ1500 ceiling mounted utility heater:
1. Locate the mode-change wheel: This is typically on the front or side of the heater and is used to switch between heat settings.
2. Identify the cord attachment point: The wheel should have a small hole or notch designed for attaching the pull cord.
3. Insert the cord: Thread one end of the pull cord through the hole or notch on the wheel.
4. Secure the cord: Tie a secure knot (such as a double knot) on the inside of the wheel to prevent the cord from slipping out.
5. Test the connection: Gently pull the cord to ensure it rotates the mode wheel smoothly and stays securely attached.
6. Adjust cord length if needed: Make sure the cord is long enough to reach comfortably from the floor or where you plan to operate it.
Always ensure the heater is off and cool before attaching the cord.
This answer is automatically generated
Jimmy Hester
May 10, 2025
HOW DO I ATTACH THE CORD TO THE WHEEL THAT CHANGES THE MODE, HIGH, LOW OR LIGHT?
1 comments:
Mr. Anderson
May 20, 2025
To attach the cord to the mode selector wheel on the ProFusion ceiling-mounted utility heater, follow these steps:
1. Locate the mode selector wheel: This is typically a small, round, notched dial on the heater’s body, often near the bottom or side.
2. Identify the cord attachment point: The cord (usually a pull string) has a small loop or hook at the end. The mode selector wheel will have a small hole or notch designed for the cord.
3. Attach the cord: - Insert the looped or hooked end of the cord into the hole or notch on the wheel. - Ensure it is securely fastened so pulling the cord turns the wheel.
4. Test the connection: - Gently pull the cord to make sure it rotates the wheel through the different modes (e.g., Off, Fan, Low, High). - Check that the wheel clicks or stops at each setting.
Make sure the heater is powered off and cool before performing this task for safety.
This answer is automatically generated
Related Manuals for ProFusion Ceiling mounted utility heater
Need help?
Do you have a question about the Ceiling mounted utility heater and is the answer not in the manual?
Questions and answers
HOW DO I ATTACH THE CORD TO THE WHEEL THAT CHANGES THE MODE, HIGH, LOW OR LIGHT? NEEDED TO ADD MODEL NO ... HQ1500
To attach the cord to the mode-change wheel on the ProFusion HQ1500 ceiling mounted utility heater:
1. Locate the mode-change wheel: This is typically on the front or side of the heater and is used to switch between heat settings.
2. Identify the cord attachment point: The wheel should have a small hole or notch designed for attaching the pull cord.
3. Insert the cord: Thread one end of the pull cord through the hole or notch on the wheel.
4. Secure the cord: Tie a secure knot (such as a double knot) on the inside of the wheel to prevent the cord from slipping out.
5. Test the connection: Gently pull the cord to ensure it rotates the mode wheel smoothly and stays securely attached.
6. Adjust cord length if needed: Make sure the cord is long enough to reach comfortably from the floor or where you plan to operate it.
Always ensure the heater is off and cool before attaching the cord.
This answer is automatically generated
HOW DO I ATTACH THE CORD TO THE WHEEL THAT CHANGES THE MODE, HIGH, LOW OR LIGHT?
To attach the cord to the mode selector wheel on the ProFusion ceiling-mounted utility heater, follow these steps:
1. Locate the mode selector wheel: This is typically a small, round, notched dial on the heater’s body, often near the bottom or side.
2. Identify the cord attachment point: The cord (usually a pull string) has a small loop or hook at the end. The mode selector wheel will have a small hole or notch designed for the cord.
3. Attach the cord:
- Insert the looped or hooked end of the cord into the hole or notch on the wheel.
- Ensure it is securely fastened so pulling the cord turns the wheel.
4. Test the connection:
- Gently pull the cord to make sure it rotates the wheel through the different modes (e.g., Off, Fan, Low, High).
- Check that the wheel clicks or stops at each setting.
Make sure the heater is powered off and cool before performing this task for safety.
This answer is automatically generated