Table of Contents
Advertisement
The diamond-shaped tip (13) can be reversed and replaced
when worn.
When the front part of the tip is worn, detach it from the
sheet, reverse it and press it onto the sanding base again.
When the whole tip is worn, remove it from the sanding
base and fit a new tip.
Tip of the sanding base (fig. F)
When the sanding base tip (14) or tip holder (15) is worn,
it can be reversed or replaced. Spare parts are available from
your Black & Decker dealer.
Remove the screw (16).
Reverse or replace the worn part.
Fit and tighten the screw.
Louvre attachment (fig. J)
With this attachment you can work in crevices and use
the sanding base on both sides.
Remove the tip of the sanding base and the tip holder (fig. F).
Fit the louvre base (22) over the tip of the pointed base.
Secure the louvre base with the screw (21).
Stick the main abrasive sheet to the underside of the
louvre base. Part of it will stick to the front part of the
pointed base.
For sanding down louvre slats on both sides, abrasive paper
can be fitted to the upperside of the attachment.
Remove the backing paper (20) from the velcro fastener (19).
Stick the velcro fastener to the top surface of the louvre
attachment.
Fit the sanding piece (18) to the velcro fastener.
Use
Warning! Do not cover the ventilation slots when using the
tool. Hold the tool as shown in fig. I. Make sure that the
sanding base is flat on the workpiece.
Switching on and off
If the tool has a variable speed control knob (2), set it to
the required speed range. As a general rule, use a low
speed for polishing and for sanding plastics. Use a high
speed for wood and metal.
To switch the tool on, press the part of the on/off switch (1)
marked 'I'.
To switch the tool off, press the part of the on/off switch (1)
marked '0'.
Automatic brake system (ABS)
This tool has an automatic brake system. When the tool is not
on the work surface, this feature keeps the speed of the round
base below the speed of the motor. When the tool is switched
off, the base will stop very quickly.
Connecting a vacuum cleaner
In order to connect a vacuum cleaner to the tool, you need a
special adaptor, which is available as an accessory.
Emptying the dustbag (fig. G)
The dustbag should be emptied every 10 minutes of use.
Hold the tool with the dustbag (5) pointing down.
Squeeze the buttons (17) to release the dustbag.
Refit the dustbag, letting it click into place.
Do not wash the dustbag.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in the new plug.
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.
Protecting the environment
Black & Decker provides a facility for recycling
Black & Decker products once they have reached the
end of their working life. This service is provided
free of charge. To take advantage of this service
please return your product to any authorised repair
agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com.
5
Advertisement
Table of Contents
