Advertisement
Set up
1
Approximate time: 10 minutes
A
Connect the green data cable from the Wi-Fi
Gateway's DSL Broadband port to your wall jack.
Data cable
Wall jack
C
Connect the Battery Backup Unit (BBU) to the
Wi-Fi Gateway's Power port. Plug the BBU into a
standard electrical outlet only. Wait until step 2
to power up the BBU.
Battery Backup
Unit (BBU)
Images are not to scale.
Electrical
outlet
Questions?
Go online:
Visit att.com/uversesupport.
b
Remove the sticker covering the Power port. Connect
the yellow Ethernet cable from the Wi-Fi Gateway's
Ethernet port to your computer's Ethernet port.
Computer Ethernet port
Ethernet cable
D
Plug one end of your phone cable into the
Wi-Fi Gateway's Phone Lines 1 & 2 port
and the other end into a standard phone or
cordless base station.
A Voice Line Splitter is required if you have
two AT&T U-verse Voice lines.
For best results, connect only the devices
and power supply depicted above.
To learn more about the benefits and features of your AT&T
U-verse service, visit att.com/u-verse/newcustomer.
Power up
2
•
Move the switch on the back of the Battery Backup Unit (BBU) to the "on"
position.
•
Your Wi-Fi Gateway is now powering up. Wait up to five minutes for the
Broadband and Service indicator lights to turn solid green.
During this time, do not unplug the bbU or green data cable, as this can
permanently damage the gateway and significantly delay your Service Activation.
•
If the Broadband and Service lights do not turn solid green or continue to
blink after 15 minutes, see the "Having Trouble?" section on the back of this
guide.
Note: The BBU must be charged for approximately 18 hours before it is fully
operational; however installation of your service may continue while the BBU
is charging. The BBU may emit a beeping sound while charging.
Important: You will have a dial tone after completing step 2, but will only be able
to make emergency and toll-free calls until you activate your service in step 3.
Register
3
Note: You must complete both activation steps in order to use your Internet and Voice services.
A
Open your Internet browser (e.g., Internet
Explorer, Safari, etc.):
•
The online registration process will start
automatically to help you activate your Internet
and Voice services. If it doesn't start, enter
att.net/uverse into your address bar.
•
Continue your online registration using the
4-digit passcode you created when you placed
your order—it was mailed to you separately for
your reference.
Phone, cordless
base station,
Go Wi-Fi
or other phone
4
device (fax)
Write down the Wi-Fi Network Name (SSID) and Wi-Fi Password (Wireless Network Key) to configure
additional Wi-Fi devices. This information is on the side of your Wi-Fi Gateway. The Wi-Fi Network Name
consists of "ATT" plus the last three digits of the Wi-Fi Gateway's serial number. Be sure to record this
information in the form below.
Now configure your Wi-Fi network:
•
Go to your computer's "Wireless Network Settings"
and refresh the network list.
•
Select your Wi-Fi Network Name (SSID) from the list.
You may need to scroll through the list to find your
SSID.
•
Enter the 10-digit Wi-Fi Password (Wireless
Network Key) in the Password field to connect to
your network.
Congratulations! You should now be
connected to the Internet via Wi-Fi.
Stay connected on the go!
AT&T Wi-Fi Basic is included with your AT&T U-verse High Speed Internet service, so you can access
the Internet at thousands of AT&T Wi-Fi Hot Spots across the country. Visit attwifi.com to learn more.
Approximate time: 15 minutes
Power
Ethernet
Wireless
Phone 1
Phone 2
USB
Broadband
Service
Wi-Fi Gateway
indicator lights
(required)
Approximate time: 20 minutes
To activate your Voice
b
service to make calls:
Call
1.877.377.0016
from the phone you set
up in step 1, and follow
the voice instructions to
complete the activation.
Upon successful activation, you will
hear the following:
"Your telephone number
has been successfully activated."
(optional)
Approximate time: 10 minutes
SSID: ATTXXX
Wireless Network Key: XXXXXXXXXX
For help: att.com/support
Wi-Fi Network Name (SSID)
A
T
T
10-digit Wi-Fi Password (Wireless Network Key)
Note:
Label is removable for safekeeping.
ON
OF F
Battery Backup Unit (BBU)
XXX.XXX.XXXX
Advertisement
