Advertisement
Set up
1
Approximate time: 10 minutes
Power down all U-verse TV receivers by unplugging them from the electrical outlets before moving on to Step
A
Insert the battery backup into your Wi-Fi Gateway
· Unplug the power cord from your Wi-Fi Gateway
· Remove the stand from the base
· Remove the cover
· Insert the battery
· Replace the cover and stand
DS L
et
Eth ern
Bro adb
4
3
es
2
ne Lin
Pho
1
Res et
er
Pow
1 & 2
C
· Connect the yellow ethernet cable from your
computer into the back of the Wi-Fi Gateway.
Data cable
Ethernet cable
Questions?
Go online:
Visit att.com/uversesupport
To learn more about the benefits and
features of your AT&T U-verse service,
visit att.com/u-verse/newcustomer
B
· Stand the Wi-Fi Gateway upright
· Connect the green data cable from the Wi-Fi
Gateway's DSL Broadband port to your wall jack
Data cable
ON T
US B
and
D
· Plug one end of your phone cable into the
Wi-Fi Gateway's Phone Lines 1 & 2 port
and the other end into a standard phone
or cordless base station.
· Plug the power cord back into the Wi-Fi Gateway
Data cable
Ethernet cable
Phone cable
For best results, connect only the devices
and power supply depicted above.
Images are not to scale.
Stay connected on the go!
AT&T Wi-Fi Basic is included with your AT&T U-verse High Speed
Internet service, so you can access the Internet at thousands of AT&T
Wi-Fi Hot Spots across the country. Visit attwifi.com to learn more.
Power up
2
A
Your Wi-Fi Gateway is now powering up. During this time, the Broadband light will turn red and the
Power light may turn orange.
1 A
.
Wait up to 15 minutes for the Service indicator light to turn solid green.
During this time (up to 15 minutes), do not unplug the power cord or the green data cable, as
this can permanently damage the Wi-Fi Gateway and significantly delay your service activation.
If the Service light does not turn solid green or continues to blink after 15 minutes,
see the
Having trouble?
B
Power up all of your TV receivers by plugging them back into the electrical outlets. This process may take several minutes.
Registration & Activation
3
Wall jack
Approximate time: 20 minutes
Note: You must complete both activation steps in order to use your Internet and Voice services.
Important: You will have a dial tone after completing Step
emergency and toll-free calls until you activate your Voice service in Step
Open your Internet browser (e.g., Internet Explorer, Safari, etc.):
A
•
The online registration process will start automatically
to help you activate your Internet and Voice services.
•
If the registration process does not start automatically:
1. Turn off security or firewall software, or give
permission to "allow the network connection"
if prompted by your browser, in order to connect to
the AT&T network.
2. Enter att.net/uverse into your address bar.
•
Continue your online registration using the 4-digit passcode you
created when you placed your order—it was mailed to you separately
for your reference.
Go Wi-Fi
4
Write down the Wi-Fi Network Name and Wi-Fi Password to configure additional Wi-Fi devices. This information
is on the side of your Wi-Fi Gateway. The Wi-Fi Network Name consists of ATT plus the last seven characters of
the Wi-Fi Gateway's serial number. Be sure to record this information in the form below.
Now configure your new
Wi-Fi network:
1. Go to your computer's "Wireless
Network Settings" and refresh the
network list.
2. Select your Wi-Fi Network Name
(SSID) from the list. You may need
to scroll through the list to find
Phone, cordless
base station,
your Wi-Fi Network Name.
or other phone
device (fax)
3. Enter the 12 character Wi-Fi
Password (Wireless Network Key)
in the Password field to connect
to your network.
4. Connect all your Wi-Fi devices with
the new Wi-Fi Network Name and
new Wi-Fi Password.
Stay connected on the go!
AT&T Wi-Fi Basic is included with your AT&T U-verse High Speed Internet service, so you can access the
Internet at thousands of AT&T Wi-Fi Hot Spots across the country . Visit
Approximate time: 15 minutes
section on the back of this guide.
, but will only be able to make
2
.
3
B
(optional)
SSID: ATTXXXXXXX
Wireless Network Key: XXXXXXXXXXXX
For help: att.com/support
Wi-Fi Network Name (SSID)
A
T
T
12 character Wi-Fi Password (Wireless Network Key)
For illustrative purposes only. Please refer to the label on your
equipment for your personal SSID and Wireless Network Key.
attwifi.com
Gateway
Power
Battery
Ethernet
Wireless
HomePNA
Broadband 1
Broadband 2
Service
Phone 1
Phone 2
USB
Wi-Fi Gateway indicator
lights on front panel.
Lights may vary with setup.
NVG589
(required)
To activate your Voice
B
service to make calls:
Call 1.877.377.0016
from the phone you set
up in Step
, and
1 D
follow the voice
instructions to
complete the activation.
Upon successful activation, you will
hear the following: "Your telephone
number
XXX.XXX.XXXX
has been
successfully activated."
Approximate time: 10 minutes
to learn more.
Advertisement
