Toshiba B-EP2DL SERIES Owner's Manual page 8

Keep away from a microwave.
Communication performance may deteriorate or a communication error may occur due to the radio emitted from a
microwave.
Since the Bluetooth and wireless LAN use the same radio frequency band, each radio wave may interfere with each
other when they are used at the same time, causing a deterioration of communication performance or a
disconnection of network. If there is any problem with connection, please stop using either Bluetooth or wireless
LAN.
Do not use the product on a metal table or near a metal object.
Communication performance may be deteriorated.
TEC-BTM-R Specification
• Bluetooth class 2
• Built-in protocol stack activated by Bluetooth V1.2 serial
port profile
• Operating temperature: -5 to 50° C 25% to 85%RH (No
condensation)
• Dimensions: 38.1 mm (W) x 25.4 mm (H) x 7 mm (D)
SD-Link 11g Specification
• Built-in IEEE802 Part 11b/g (802.11b/g)
• Operating temperature: 0 to 50° C 25% to 85%RH (No condensation)
• Dimensions: 47.0 mm (W) x 24.0 mm (H) x 4.7 mm (D)
CAUTION!
1.To avoid injury, be careful not to catch or jam your fingers while opening or closing the cover.
2.Do not touch moving parts. To reduce the risk that fingers, jewellery, clothing, etc., be drawn into the moving
parts, turn off the power switch to stop movement.
Safety Summary
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions
necessary for safe handling are included in this manual. All warnings and cautions contained in this manual
and written inside or outside of the printer should be read and understood before handling or maintaining the
equipment.
Do not attempt to effect repairs to this equipment.
procedures described in this manual, turn off the power, then contact your authorised TOSHIBA TEC
representative for assistance.
Safety Precautions
This Owner's Manual and the products (machines) which you have purchased contain indications which should
be observed in order to use the machines safely and prevent harm to yourself and others and damage to
property. The meanings of these indications and symbols are given below.
Read these indications and become familiar with their contents before reading this Owner's Manual.
Precautions
The following precautions will help to ensure that this machine will continue to function correctly.
(1) Try to avoid locations that have the following adverse conditions:
*Temperatures out of the specification
*High Humidity
*Direct sunlight
*Excessive vibration
(2) The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent
solution. NEVER USETHINNER OR ANY OTHER VOLATILE SOLVENT on the plastic covers.
(3) USE ONLY TOSHIBA TEC SPECIFIED media.
(4) DO NOT STORE the media where it might be exposed to direct sunlight, high temperatures, high humidity,
dust, or gas.
(5) Any data stored in the memory of the printer could be lost during a printer fault.
(6) DO NOT open the top cover and battery cover during operation. Doing so will stop printer operation.
(7) DO NOT scratch the surface of printed labels or receipt with a sharp object.
(8) Be sure to use a shielded interface cable.
CAUTION!
1.This manual may not be copied in whole or in part without the prior written permission of TOSHIBA TEC.
2.The contents of this manual may be changed without notification.
3.Please refer to your local Authorised Service representative with regard to any queries you may have in this
manual.
BTM411 Specification
• Bluetooth class 2
• Built-in protocol stack activated by Bluetooth V2.1+EDR
serial port profile
• Operating temperature: -15 to 50° C 25% to 85%RH (No
condensation)
• Dimensions: 22.5 mm (W) x 12 mm (H) x 3.4 mm (D)
(Only Module condition)
If a fault occurs that cannot be rectified using the
7