Table of Contents
Advertisement
QQ
3 7 63 1515 0
PANEL VIEWS
REAR PANEL
10
TAPE IN/OUT
These analog inputs and outputs can be used to con-
nect a cassette recorder, Mini Disc recorder, or other
recorder with analog inputs and outputs.
MONITOR OUT
11
This S-V ideo or composite video output can be con-
nected to the video input on your TV or projector .
12
ZONE 2 OUT
These composite video and analog audio outputs
can be used to feed a TV and an integrated amp in
Zone 2.
DVD IN
13
These S-Video, composite video, and analog audio
inputs can be used to connect a DVD player.
VIDEO 1 & 2 IN/OUT
14
These S-Video, composite video, and analog audio
inputs and outputs can be used to connect one or
two video recorders (e.g., VCRs).
15
VIDEO 3 & 4 IN
These S-Video, composite video, and analog audio
inputs can be used to connect one or two video
sources (e.g., cable TV , satellite TV, or a set-top
box).
COMPONENT VIDEO OUTPUT
16
TE
L 13942296513
This component video output can be used to con-
nect a TV or projector with a component video
input.
17
COMPONENT VIDEO INPUT 1 & 2
These component video inputs can be used to con-
nect one or two AV components with component
video outputs, such as a DVD player.
18
ETHERNET (Net-Tune)
This port is for connecting the DTR-8.4 to your
Ethernet network (i.e., router or switch) for use with
Net-Tune (i.e., Internet radio and MP3 and WAV
playback).
SPEAKERS
19
These terminal posts are for connecting your speak-
ers. The SURR BACK/ZONE 2 terminals can be
used with surround back speakers in the main room
or speakers in another room (Zone 2).
www
.
http://www.xiaoyu163.com
.
x
ao
u163
y
i
http://www.xiaoyu163.com
2 9
8
20
RS232
This port is for connecting the DTR-8.4 to home
automation and external controllers.
IR IN/OUT
21
If you want to use the remote controller to control
the DTR-8.4 from Zone 2, or if the DTR-8.4 is
installed in a cabinet and the line of sight between
the DTR-8.4 and the remote controller is obstructed,
a commercially available IR recei v er can be con-
nected to the IR IN. A commercially available IR
emitter can be connected to the IR OUT to pass the
IR signals along to another AV component.
22
12V TRIGGER OUT ZONE 2/A/B
These outputs can be connected to the 12-volt trig-
ger inputs on other components. They output 12
volts (100 milliamperes max). The ZONE 2 TRIG-
GER OUT outputs 12 volts while the DTR-8.4 is in
Zone 2 mode. The A and B outputs can be assigned
to input sources, in which case, the assigned trigger
output outputs 12 v olts while the input source is
selected.
REMOTE CONTROL
23
This
(Remote Interactive) sock et can be con-
nected to the
Q Q
AV component. The DTR-8.4's remote controller
3
6 7
1 3
1 5
can then be used to control that component. To use
, you must make an analog RCA/phono audio
component, even if they are connected digitally.
24
AC INLET
The supplied power cord should be connected here.
25
AC OUTLETS
These switched AC outlets can be used to supply
power to other AV components. The connector type
depends on the country in which you purchased
your DTR-8.4.
26
Grounding screw
This scre w is for connecting a turntable's ground
wire.
co
.
8
9 4
2 8
socket on another Inte gra/Onk yo
0 5
8
2 9
9 4
2 8
m
DTR-8.4
9 9
9 9
AV
Advertisement
Table of Contents
