Page 3
INDEX Diagram 5.3.8 Heating elements (electric oven GN 1/1) 5.3.9 Heating elements (electric oven GN 2/1) Features of the appliances 5.3.10 Fan for electric and gas ovens GN 1/1 5.3.11 Solid top burner Technical data 9-10 5.3.12 Solid top tap 5.3.13 Solid top pilot burner 4 Installation instructions 5.3.14 Solid top ignition plug...
Description Dimensions in mm. (LxPxH) AGB 499/WP 2 burners - table top 400 x 700 x 270/340 51BQ2896 AGB 483/WP 4 burners with open compartment 800 x 700 x 900/970 51BQ2896 AGB 500/WP 4 burners - table top 800 x 700 x 270/340...
Page 10
3 - TECHNICAL DATA TABLE 1 Model Solid Gas oven Gas oven Gas oven Ø 100 Ø 120 Gas range GN 1/1 GN 2/1 MAXI Category II2H3+ Construction type Air necessary for combustion Nominal thermal power 12.0 Minimum thermal power 0.75 Overall thermal power (gas) Hour consumption...
4 - INSTALLATION INSTRUCTIONS 4.1 Safety rules and steel (for MAXI), is in two pieces. The smoke collector is in aluminised sheet metal and the protection grill is in enamelled cast iron. • Only a local gas utility technician is authorized to carry out gas installations and connections.
4 - INSTALLATION INSTRUCTIONS If the type of gas indicated on the data plate of the appliance does 4.3.6 Smoke extraction not correspond to the gas which is present, refer to the paragraph These kitchens are type A appliances, thus no smoke extraction sys- "Conversion and adaptation".
5 - SET-UP FOR OPERATION Fig. 1 5.1.4 Power check with volumetric method 5.1.6 Check of pilot flame Using a gas meter and a stopwatch, you can read the volume of gas For proper regulation, the pilot flame must surround the thermo- output per time unit.
5 - SET-UP FOR OPERATION 5.1.9 Operator training 5.1.15 Replacement of pilot nozzle for gas oven GN 2/1 • Explain and show the user how the machine works according to (Fig. 2A) the instructions, and hand him this manual. • Remind the user that any structural alterations or any building Remove the lower panel as previously described.
5 - SET-UP FOR OPERATION Fig. 3A Fig. 3B 5.2 Maintenance 5.3 Replacing parts Attention! Before doing any repair or maintenance work, unplug the appliance. All parts must be replaced by authorized technicians only! The following maintenance program should be carried out at least once a year: To replace the following parts first remove all the control knobs and control panel (after loosening the fixing screws), then extract the...
Page 17
5 - SET-UP FOR OPERATION 5.3.7 Gas oven main burner (Fig. 2A) 5.3.11 Solid top burner (40, Fig. 5) Unscrew the fastening screw (19) of the main burner and replace it Remove the cast-iron plate and the control panel after loosening with a new one.
6 - INSTRUCTIONS FOR USE 6.1 Safety, cleaning and repair rules essential features. The manufacturer declines all responsibility for any non-compliance with the provisions contained in this manual. • This appliance is used for the preparation of meals at industri- al level.
Page 19
6 - INSTRUCTIONS FOR USE Fig. 4B 6.3.3 Lighting gas oven GN 1/1 (Fig. 3B) In this position the top heating element (from above) and the bottom heating element (from below) are on, and at the Turn on the switch located up the line from the unit. Press the knob same time the fan is in operation (convection).
6 - INSTRUCTIONS FOR USE 6.7 Turning the appliance off in case of A more powerful effect is given by oxidative acids (nitric acid, oxalic breakdown acid). These acids are used if the steel has undergone strong chemi- cal stresses, hence generally losing its inactive coat. In case of breakdown, shut down the appliance as instructed in the The inactive layer can be chemically damaged or jeopardized by paragraph "Shutdown".
Page 21
6 - INSTRUCTIONS FOR USE NOTE Fig. 5 54 50 064_03 - GAS KITCHENS 07/2007 21 · 26...
Page 22
6 - INSTRUCTIONS FOR USE 6.9.3 The 2002/96/EC (WEEE) Directive: information to users This informational note is meant only for owners of equipment marked with the symbol shown in Fig. A on the adhesive label featu- ring the technical specifications applied on the actual product (the label also giving the serial number): This symbol indicates that the product is classified, according...
7 - APPENDIX: ELECTRICAL DIAGRAMS AGB 493/WP • AGB 495/WP Terminal board Grill heating element Commutator Bottom heating element Green indicator light Fan heating element Yellow indicator light Motorized fan Top heating element Thermostat 064_03 - GAS KITCHENS 07/2007 23 · 26...
Page 24
7 - APPENDIX: ELECTRICAL DIAGRAMS AGB 486/WP ADN 019/WP • ADN 021/WP L 2 L 3 400 V 3N ~ 8.48 A R1/R2 L1 L 2 L 3 230 V 3 ~ 14.75 A R1/R2 230 V ~ 25.7 A Connected power: 5.9 kW 230/400 Terminal Indicator light (power)
Page 25
7 - APPENDIX: ELECTRICAL DIAGRAMS AGB 486/WP ADN 019/WP • ADN 021/WP R1/R2 L1 L 2 L 3 230 V 3 ~ 14.75 A Terminal board Switch R1/R2 Thermostat Temperature limiter Green indicator light Orange indicator light Upper heating elements 230 V ~ 25.7 A Lower heating elements AGB 492/WP •...
Page 26
THE MANUFACTURER CANNOT BE HELD RESPONSIBLE IF THE INSTRUCTIONS CONTAINED IN THIS MANUAL ARE NOT OBSERVED. THIS DOCUMENTATION IS ONLY INTENDED FOR QUALIFIED TECHNICIANS WHO ARE AWARE OF THE RESPECTIVE SAFETY REGULATIONS. WHIRLPOOL EUROPE srl V.le Guido Borghi, 27 I – 21025 Comerio – VA...
Need help?
Do you have a question about the AGB 483/WP and is the answer not in the manual?
Questions and answers