Advertisement

A6500
For any needed assistance please call 1-866-872-5722
****Warning do not plug water cooler in until water line is in place and dispensing water
through the faucets****
WARNING: This product is intended for indoor use only. Outside temperatures can cause damage to all systems. Please use only inside your home or office.
Phillips head screw driver
Very sharp pair of scissors or a very sharp knife to cut tubing
Zip Ties (provided in water line kit)
Poly Tubing (provided in water line kit)
Water filter
WARNING: YOU MUST OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES FOR INSTALLATION, OR THE
If you do not own the property where the unit will be installed, you need to contact the owner and obtain
approval before you install your cooler. If you are not comfortable with the installation procedure it is
WARNING: Do not use a saddle valve for installation or the warranty will be voided

Items You Need

To find the Aquverse warranty please go to www.aquverse.com
Aquverse Water Cooler Installation and Troubleshooting Instructions
WARRANTY WILL BE VOIDED.
recommended to have a professional licensed plumber complete the install for you.
Angle stop fitting (size depends on your water source, adaptable fitting
Quick connect (2 sided coupler for poly line, provided in water line kit)
Safety Glasses (Wear these at all times during installation)
provided in water line kit)
Adjustable crescent wrench
Drill with a 3/8 bit

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Water Cooler and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Aquverse Water Cooler

  • Page 1 If you are not comfortable with the installation procedure it is ****Warning do not plug water cooler in until water line is in place and dispensing water recommended to have a professional licensed plumber complete the install for you.
  • Page 2 Cooler Set Up First Steps Filter Specifications Determine where your cooler is going to be located and place it close to the determined area This drinking water system must be maintained in accordance with the manufacture's instructions DO NOT PLUG IN (see instructions that are provided with filter) A professional licensed plumber can perform the install or you can obtain the following items at your local hardware store: Maximum PSI = 10-125 psi/Capacity = 1500 gallons/Temperature = 35-100 F...
  • Page 3 Locate Water Source WARNING: YOU MUST OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES A water source looks like this. It can be typically found underneath the closest sink to were you would like to place your cooler Locate the cold water source Make sure that the water source you will work with is connected to the cold faucet on you sink by a water line hose.
  • Page 4 Connect the two sided quick connect to the water line running out of Insert water line kit tubing into quick connect on angle stop the bottom back corner of you water cooler. Run tubing from water source to cooler. If water source is located in a...
  • Page 5 Flushing the Filter You must flush water through the filter to wash excess carbon out before There is no danger in drinking the water with the carbon residue drinking (this is commonly referred to as priming the filter, and is discoloring the liquid, however for the freshest tasting and looking required) water it is beneficial to flush the system.
  • Page 6 Cooler Is Not Dispensing any Water Confirm that cooler is not frozen by checking inside water tank, and determining if water is frozen. If frozen unplug the water cooler and let Check faucets to determine if water is blocked by any obstructions thaw, then proceed to the next step.
  • Page 7 Using a chopstick or screwdriver, depress the hot tank reset button Reset the hot tank by first unplugging the water cooler, then proceed to (water should be hot in 30 minutes time, see figure below which...
  • Page 8 Cleaning Your Water Cooler Turn the water source off Fill the cold water tank with approximately four glasses of water Unplug cooler Drain this water through the cooler by opening the cold water faucet Drain water out of the hot faucet until the water reaches room...
  • Page 9 Remove the drain plug from the rear of the cooler (water will drain out of the cooler immediately, so you will need a bucket or receptacle to catch Install the float valve back to its original placement as noted before the water Remove the baffle from the cooler and clean with a clean dish towel, and water (do not use bleach or any cleaners, you may use a small amount of...
  • Page 10 TURN OFF WATER! Insert the previously removed screw into the bottom of the cabinet Remove the attached filter by turning to the left until it stops cover Pull down gently on the filter until it is removed Re-attach the drip tray by pushing in For any needed assistance please call 1-866-872-5722...

Table of Contents

Save PDF