Table of Contents
Advertisement
1PH
For any needed assistance please call 1-866-872-5722
****Warning do not plug water cooler in until water line is in place and dispensing water
through the faucets****
WARNING: This product is intended for indoor use only. Outside temperatures can cause damage to all systems. Please use only inside your home or office.
Phillips head screw driver
Very sharp pair of scissors or a very sharp knife to cut tubing
Zip Ties (provided in water line kit)
Poly Tubing (provided in water line kit)
Water filter
WARNING: YOU MUST OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES FOR INSTALLATION, OR THE
If you do not own the property where the unit will be installed, you need to contact the owner and obtain
approval before you install your cooler. If you are not comfortable with the installation procedure it is
WARNING: Do not use a saddle valve for installation or the warranty will be voided
Items You Need
To find the Aquverse warranty please go to www.aquverse.com
Aquverse Water Cooler Installation and Troubleshooting Instructions
WARRANTY WILL BE VOIDED.
recommended to have a professional licensed plumber complete the install for you.
Angle stop fitting (size depends on your water source, adaptable fitting
Quick connect (2 sided coupler for poly line, provided in water line kit)
Safety Glasses (Wear these at all times during installation)
provided in water line kit)
Adjustable crescent wrench
Drill with a 3/8 bit
Advertisement
Table of Contents
Related Manuals for Aquverse 1PH
Summary of Contents for Aquverse 1PH
- Page 1 Quick connect (2 sided coupler for poly line, provided in water line kit) Poly Tubing (provided in water line kit) Drill with a 3/8 bit Water filter Safety Glasses (Wear these at all times during installation) To find the Aquverse warranty please go to www.aquverse.com...
- Page 2 Cooler Set Up First Steps Filter Specifications Determine where your cooler is going to be located and place it close to the determined area This drinking water system must be maintained in accordance with the manufacture's instructions DO NOT PLUG IN (see instructions that are provided with filter) A professional licensed plumber can perform the install or you can obtain the following items at your local hardware store: Maximum PSI = 10-125 psi/Capacity = 1500 gallons/Temperature = 35-100 F...
- Page 3 Locate Water Source Locate the cold water source A water source looks like this. It can be typically found underneath the Make sure that the water source you will work with is connected to the closest sink to were you would like to place your cooler cold faucet on you sink by a water line hose.
- Page 4 Installing Water Line Kit Unscrew the cold water line hose from the shut off valve (you will have a Use the Water Line Kit clips to affix the tubing underneath the cabinet few ounces of water remaining in the hose that will drip out) alongside kick plate, or along wall to help keep out of sight.
- Page 5 Flushing the Filter You must flush water through the filter to wash excess carbon out before There is no danger in drinking the water with the carbon residue drinking (this is commonly referred to as priming the filter, and is discoloring the liquid, however for the freshest tasting and looking required) water it is beneficial to flush the system.
- Page 6 Cooler Troubleshooting What To Do If Cooler Is Not Dispensing any Water Confirm that cooler is not frozen by checking inside water tank, and determining if water is frozen. If frozen unplug the water cooler and let Check faucets to determine if water is blocked by any obstructions thaw, then proceed to the next step.
- Page 7 Cooler is dispensing water but it is not Hot Check the back of the cooler, and make sure the hot tank switch is in the Turn the cooler around so you are facing the back (wire caged portion) on position of the cooler If hot tank switch is on then you will need to reset the hot tank (this can Locate the hot tank through the back cage, and then locate the hot tank...
- Page 8 Cleaning Your Water Cooler Turn the water source off Fill the cold water tank with approximately four glasses of water Unplug cooler Drain this water through the cooler by opening the cold water faucet Drain water out of the hot faucet until the water reaches room Fill the cold water tank again with approximately four glasses of water temperature (note that water is going to be hot when you begin draining) Drain this water through the cooler by opening the hot water faucet...
- Page 9 Clean the cold tank with a clean dish towel, and water (do not use bleach or any cleaners, you may use a small amount of soap if desired) Replacing Your Water Filter Remove the screw located at the top of the back of the water cooler Pull down gently on the filter until it is removed Attach filter to filter head by pushing in, and turning to the right until it Lift upwards at the back of the top cover and pull towards you...
Need help?
Do you have a question about the 1PH and is the answer not in the manual?
Questions and answers
button the dispenses the cold water is broke where can I get one to replace the broken one