Tv-System; System; Adjusting The Position; Position - Panasonic PT-D5600E Operating Instructions Manual

AI
Gray scale control is exercised to suit the images,
and optimal images with a clear contrast are
projected.
ON : AI compensation is enabled.
OFF : AI compensation is disabled.

TV-SYSTEM

(For S-Video/Video signals)
The setting that corresponds to the TV system is
selected here.
AUTO1 : Standard setting
Automatically selects the TV standard
that matches the input video signal, out
of NTSC, PAL, NTSC4.43, SECAM and
PAL60.
AUTO2 : Automatically selects the TV standard
that matches the input video signal, out
of NTSC, PAL-M, and PAL-N.
• Normally "AUTO1" or "AUTO2" should be
chosen for this option.
• If the video signals are not displayed properly
due to signal deterioration, choose the TV
system that matches the input video signals.
Automatically selected by detecting the
horizontal/vertical scan frequencies and colour sub-
carrier listed in the table below:
H. Scan
Signal
Frequency

System

(kHz)
NTSC 15.75
NTSC4.43 15.75
PAL 15.63
PAL-M 15.75
PAL-N 15.63
SECAM 15.63
PLA60 15.75
SYSTEM
(For RGB/YP P
B
This enables the RGB system or YP
be selected.
For the signals which are supported, refer to page
58.
Downloaded From projector-manual.com Panasonic Manuals
V. Scan Colour
Frequency Subcarrier
(Hz) (MHz)
60.00
60.00
50.00
60.00
50.00
50.00 4.25 or 4.41
60.00
signals)
R
P system to
B R

Adjusting the position

POSITION

ASPECT

ZOOM
CLOCK PHASE
KEYSTONE
SELECT
POSITION
The position where the images are displayed can
be moved here.
ASPECT
AUTO : (For S-Video/Video signals only)
16:9
4:3
3.58
4.43
3.58
4.43
S4:3
HV FIT : At this setting, the images are displayed
1 S1 video signals are 16:9 video signals to
which is added the detection signal output from
the video deck or other unit which supports the
wide-screen format.
2 Here, the standard signal means 4:3 or 5:4
input signals.
3 Here, the wide-screen signals means 16:9,
15:9 or 15:10 input signals.
POSITION
4 : 3
16
ENTER RETRN
: The position is moved horizontally.
: The position is moved vertically.
At this setting, when S1 video signals
are identified as being input to the S-
Video connector or video ID signals are
identified as being input to the video
connector, the images are displayed
after automatically being converted to
the 16:9 aspect ratio.
: At this setting, when standard signals
are input, the images are converted to
the 16:9 aspect ratio and displayed.
When wide-screen signals
the images are displayed with their
inherent aspect ratio intact.
: At this setting, when standard signals
are input, the images are displayed with
their inherent aspect ratio intact. When
wide-screen signals 3 are input, they are
converted by the PT-D5600E to the 4:3
aspect ratio and displayed. With the PT-
DW5000E, the images are reduced in
size and displayed without converting
their aspect ratio so that they will fit onto
a screen with a 4:3 aspect ratio.
: Select this setting when using a 16:9
screen.
to fill the entire screen.
If the aspect ratios of the input signals
and screen differ, the images are
converted into the screen's aspect ratio
(4:3 for the PT-D5600E or 15:9 for the
PT-DW5000E) and displayed.
(Continued on next page)
1
2
are input,
3
2
29