ACTi I91 Hardware Manual
  1. Manuals
  2. Brands
  3. ACTi Manuals
  4. Security Camera
  5. I91
  6. Hardware manual

ACTi I91 Hardware Manual

Indoor ptz camera
Hide thumbs Also See for I91:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation Manual
Indoor PTZ Camera
Hardware Manual
I91, I92, KCM-8111
Ver. 2014/01/14

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the I91 and is the answer not in the manual?

Questions and answers

Related Manuals for ACTi I91

Summary of Contents for ACTi I91

  • Page 1 Indoor PTZ Camera Hardware Manual I91, I92, KCM-8111 Ver. 2014/01/14...

  • Page 2: Table Of Contents

    Mounting on Straight Wall ............. 34 Using the L-Type Wall Mount ............34 Other Straight Wall Mounting Solutions ........37 Other Accessories and Adjustments How to Replace the Dome Cover ........... 38 How to Reset the Camera............... 39 Resetting KCM-8111 Camera ............39 www.acti.com...
  • Page 3 Hardware Manual Resetting I92 / I93 Camera ............39 Accessing Camera Configure the IP Addresses ............40 Access the Camera ................. 44 www.acti.com...

  • Page 4: Precautions

    Every reasonable care has been taken during the writing of this manual. Please inform your local office if you find any inaccuracies or omissions. We cannot be held responsible for any typographical or technical errors and reserve the right to make changes to the product and manuals without prior notice. www.acti.com...
  • Page 5 This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to European Standard EN 55022 and EN 55024. In a domestic environment, this product may cause radio interference in which cause the user may be required to take adequate measures. www.acti.com...

  • Page 6: Safety Instructions

    1) When the power-supply cord or plug is damaged 2) If liquid has been spilled, or objects have fallen into the video product. 3) If the video product has been directly exposed to rain or water. www.acti.com...
  • Page 7 Safety Check Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine if the video product is in proper operating condition. www.acti.com...

  • Page 8: Introduction

    This hardware manual contains the following models: 2MP Indoor PTZ with D/N, Advanced WDR, SLLS, 18x Zoom KCM-8111 lens 1MP Indoor PTZ with D/N, Extreme WDR, SLLS, 30x Zoom lens 2MP Indoor PTZ with D/N, Extreme WDR, SLLS, 30x Zoom lens www.acti.com...

  • Page 9: Package Contents

    Hardware Manual Package Contents Camera Power Adapter Universal Plug Converter Surface Mount Mounting Screw Kit Fixing Bracket Terminal Block Terminal Block Drill Template (for Power) (for DIO/DO) Drill Template Quick Installation Guide Warranty Card www.acti.com...

  • Page 10: Physical Description

    Connect DC power source to the terminal block. The wire with white dashed lines is the live wire, which should connect to the 12V pin. 6) Ethernet Port The Ethernet port connects to a network using a standard Ethernet cable. www.acti.com...

  • Page 11: Internal View

    The Power LED lights red when the camera is powered up. 3) Reset Button The Reset Button is used to restore the factory default settings of the camera, including the administrator’s password. See How to Reset the Camera on page 39. www.acti.com...

  • Page 12: Before Installation

    However, the plastic has been removed on the pictures in this documentation to show clarity of the procedures being described. 1. Rotate the dome cover counter-clockwise to remove it. 2. Remove the Styrofoam. www.acti.com...

  • Page 13: Preparing The Power Adapter

    The power adapter must be connected to the supplied terminal block before use. To do this, follow the procedures below: 1. Loosen the screws of the 12V and GND pins of the power terminal block. www.acti.com...
  • Page 14 3. Connect the wire with the white stripe to the 12V pin and the other to the GND pin. 4. Tighten the screws of the 12V pin and the GND pins to secure the wire connection. 5. Attach one of the bundled adapter plugs suitable in your location. www.acti.com...

  • Page 15: Preparing The Di/Do Connector

    Connect the wires of the first input device to GND Digital Input 1 (Pin 1) and DI1 (Pin 3). (DI1) Connect the wires of the second input device to GND Digital Input 2 (Pin 5) and DI2 (Pin 7). (DI2) www.acti.com...
  • Page 16 In this case, wire connection to Pins 1 to 4. Use the GND and DI1 pins to connect a DI device and use the 12V and DO1 pins to connect a DO device. See wiring scheme below: Consequently, to connect a second DI or DO device, wire the connection to Pins 5 to 8. www.acti.com...
  • Page 17 110V-220V AC External Power Source Relay (DO1 Device) Camera Illuminator NOTE: For more information on DI/DO connections, please refer to the article All about Digital Input and Digital Output (http://www.acti.com/kb/detail.asp?KB_ID=KB20091230001) in the Knowledge Base section of our website (www.acti.com). www.acti.com...

  • Page 18: Installation Procedures

    24 for mounting instructions. PMAX-1010 Pendant Mount Suitable when mounting the camera on hard and high ceilings. PMAX-0110 PMAX-0103 (Straight Tube with Bracket) PMAX-0110 PMAX-0102 (Straight Tube) Straight Wall Suitable when mounting the camera on straight walls. Mount PMAX-0311 (L-Type Wall Mount) www.acti.com...
  • Page 19 Suitable when mounting the camera on vertical poles. Mount PMAX-0110 PMAX-0305 PMAX-0503 Horizontal Pole Suitable when mounting the camera on horizontal poles. Mount PMAX-0110 PMAX-0102 PMAX-0503 Corner Mount Suitable when mounting the camera on a corner wall. PMAX-0110 PMAX-0305 PMAX-0402 www.acti.com...

  • Page 20: Other Mounting Accessories

     For more information about the mounting solutions and accessories, please check the Mounting Accessory Selector in our website (http://www.acti.com/mountingselector).  Except for the Surface Mount, the above mounting accessories are not included in the package. Contact your sales agents to purchase.

  • Page 21: Mounting On The Ceiling

    1. Using the mount drill template, mark the screw holes on the ceiling, then drill the holes and insert the supplied plastic plugs. 2. Push at the marked points below to detach the cover ring from the metal plate. 3. Attach the metal plate to the ceiling using the three (3) supplied screws. www.acti.com...
  • Page 22 (holes marked below). The fixing bracket will fix the camera position when mounted later. 5. Align and insert the camera base hooks to the mounting holes of the metal plate. 6. Slide the camera clockwise to secure the hooks to the mount. www.acti.com...
  • Page 23 10. Note that the cables will pass through the cut, align the metal plate hooks onto the holes of the cover ring and then push to secure it in place. Final installation would look similar to the picture below. www.acti.com...

  • Page 24: Using The Flush Mount

    Step 1: Drill a Hole on the Ceiling Drill a 184-mm diameter hole on the ceiling where you want to mount the camera, then route the network cable, power adapter, and other cables (e.g. DI/DO, audio cables, etc.) through the hole. www.acti.com...
  • Page 25 Peel off the lining of the three (3) foam rubber pads and attach a rubber pad to each retaining bracket. Step 3: Loosen the Retaining Brackets Using a screwdriver, loosen the retaining brackets according to the thickness of the ceiling. www.acti.com...
  • Page 26 2. Position the retaining brackets to hold the mount on the ceiling. NOTE: The following illustration shows how the flush mount will look like when viewed from inside the ceiling. In case you cannot access inside the ceiling, use your fingers to position the retaining brackets through the hole. www.acti.com...
  • Page 27 (if necessary) are routed on the outer gap of the metal bracket. 4. Attach the fixing bracket to one of the holes on the camera using the supplied screw (holes marked below). The fixing bracket will fix the camera position when mounted later. www.acti.com...
  • Page 28 The bundled network extension cable is flexible enough to be bent and makes it easy to insert the camera through the mount.  Or, if you can access the inside of the ceiling, you may mount the camera first and then connect the cables. www.acti.com...
  • Page 29 3. Tighten the screw on the fixing bracket to fix the camera position. This is to avoid accidental camera movement as the camera performs PTZ functions. Step 7: Attach the Cover Ring 1. Align the metal latches and the latches on the cover ring. 2. Push to firmly secure the cover ring latches. www.acti.com...

  • Page 30: Using The Pendant Mount

    Note that you must insert the power adapter cable first to fit the tube. NOTE:  If using a straight tube without bracket, route the cables to pass through the hole on the ceiling.  The following illustrations show the installation using a straight tube with bracket. www.acti.com...
  • Page 31 1. Insert the cables from the tube into the mount kit and route them to pass through the outer bracket. 2. Align the slot of the mount kit to the tab inside the straight tube and install the mount kit. www.acti.com...
  • Page 32 If the network cable texture is rough and not easily bent, use the bundled network extension cable (included in the mount kit package) to easily route the cables because of its flexibility. 2. Align and insert the camera base hooks to the mounting holes. www.acti.com...
  • Page 33 3. Slide the camera counter-clockwise to secure the hooks to the mount. 4. On the top of the mount kit, attach three (3) screws (included in the mount kit package) to secure the camera to the mount. The final installation would look similar to the one below: www.acti.com...

  • Page 34: Mounting On Straight Wall

    Route the cable(s). 2a. If the cable(s) will pass through the wall, insert the cable(s) through the cable hole as marked below (A). 2b. If the cable will go along the wall, remove the pre-cut tab on the L-type wall mount www.acti.com...
  • Page 35 L-type wall mount onto the wall. Step 2: Install the Camera 1. Connect the network cable to the Ethernet port of the camera. If necessary, connect the other cables (such as power adapter, DI/DO, etc.) to the corresponding connectors. www.acti.com...
  • Page 36 2. Align and insert the camera base hooks to the mounting holes. 3. Slide the camera clockwise to secure the hooks to the mount. 4. Attach three (3) screws (included in the L-type wall mount package) to secure the camera to the mount. www.acti.com...

  • Page 37: Other Straight Wall Mounting Solutions

    NOTE: The above mentioned mounting accessories are not included in the camera package. Contact your sales agents to purchase. Download the Installation Guide from Mounting Accessory Selector in our website (http://www.acti.com/mountingselector) for detailed installation instructions. www.acti.com...

  • Page 38: Other Accessories And Adjustments

    Depending on your surveillance needs, you may want to replace the bundled dome cover with a smoke dome cover available for purchase. To replace the dome cover, do the following: 1. Rotate the dome cover counter-clockwise to remove it. 2. Rotate the replacement dome cover clockwise to attach it. www.acti.com...

  • Page 39: How To Reset The Camera

    4. Wait for 45 seconds and release the reset button. Resetting I92 / I93 Camera With the camera powered on, press and hold the reset button for at least 5 seconds or until the Power LED goes off (using a sharp object, such as a pen). www.acti.com...

  • Page 40: Accessing Camera

    Windows system – just by pressing the “Network” icon, all the cameras of the local area network will be discovered by Windows, thanks to the UPnP function support of our cameras. In the example below, the camera that has just been connected to the network is successfully found. www.acti.com...
  • Page 41 The IP Utility can be downloaded for free from http://www.acti.com/IP_Utility When you launch IP Utility, the list of connected cameras in the network will be shown. See sample illustration below: You can quickly notice the KCM-8211 model in the list.
  • Page 42 PC has to be configured to match the network segment of the camera. Manually adjust the IP address of the PC In the following example, based on Windows 7, we will configure the IP address to 192.168.0.99 and set Subnet Mask to 255.255.255.0 by using the steps below: www.acti.com...
  • Page 43 In such case, please plug in only one camera at a time, and change its IP address by using the Web browser before plugging in the next one. This way, the Web browser will not be confused about two devices having the same IP address at the same time. www.acti.com...

  • Page 44: Access The Camera

    Now that the camera and the PC both have their unique IP addresses and are under the same network segment, you can use Microsoft Internet Explorer on the PC to access the camera. You can use any of the browsers to access I91 or I92 cameras, however, the full functionality is provided only for Microsoft Internet Explorer.
  • Page 45 HTTP port of the camera is 80, which can be omitted from the address for convenience. Before logging in, you need to know the factory default Account and Password of the camera. Account: Admin Password: 123456 For further operations, please refer to the Firmware User’s Manual. www.acti.com...

This manual is also suitable for:

I92Kcm-8111

Table of Contents