Advertisement
MultiFire Electric Suite
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electrical
shock, and injury to persons, including the following:
If the appliance is damaged, check with the supplier
before installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings of a bath,
shower or swimming pool.
Do not locate the heater immediately below a fixed socket
outlet or connection box.
Do not cover the heater. Do not place material or garments
on the heater, or obstruct the air circulation around the
heater, for instance by curtains or furniture, as this could
cause overheating and a fire risk.
This appliance is not intended for use by children or other
persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them
from using it safely. Children should be supervised to
ensure that they do not play with the appliance.
Do not use this heater in series with a thermal control, a
program controller, a timer or any other device that
switches on the heat automatically, since a fire risk exists
when the heater is accidentally covered or displaced.
Ensure that furniture, curtains or other combustible
material are positioned no closer than 1 metre from the
heater.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Although this heater complies with safety standards, we
do not recommend its use on deep pile carpets or on
long hair type of rugs.
The appliance must be positioned so that the plug is
accessible.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified
person in order to avoid a hazard.
Keep the supply cord away from the front of the heater.
General
Unpack the heater carefully and retain the packaging for possible future
use, in the event of moving or returning the fire to your supplier.
The fire incorporates a flame effect, which can be used with or without
heating, so that the comforting effect may be enjoyed at any time of the
year. Using the flame effect on its own only requires little electricity.
These models are designed to be free standing and are normally
positioned against a wall.
Before connecting the heater check that the supply voltage is the same
as that stated on the heater.
Please note: Used in an environment where background noise is very
low, it may be possible to hear a sound which is related to the operation
of the flame effect. This is normal and should not be a cause for
concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating
instructions.
Wall fixing - see Fig. 1
Attach the wall brackets to the appliance with the screws supplied -
see Fig. 1.
The appliance should then be securely fixed to the wall using the wall
plug and screw supplied for block walls.
Note – for studded walls special fasteners are required, see diagram
for recommended position of fixing screws.
Controls - see Fig. 2
The fire controls are located at the base of the fire behind the bottom
panel - see Fig. 2.
Switch 1
Controls the electricity supply to the heater.
Note: This switch must be in the ON position for the heater to operate
with or without heat.
Switch 2
Controls the function of the fire.
Press once to give flame effect only.
Press again to give heat and flame effect.
Press again to go back to flame effect only.
Pressing
at any stage turns the fire to standby mode.
Note: To turn fire completely off use switch 1.
Thermostat T
In order to maintain a certain room temperature, set the controller to
'max.'. Operate the appliance at full power until the required room
temperature is reached. Set back the thermostatic controller until the
appliance switches off. This temperature will be kept almost constant
by the thermostatic control switching on and off automatically.Please
note that the appliance can only be switched on when the thermostat
setting is higher then the room temperature.
Dimmer D
To increase or decrease the brightness of the top led light, use the
dimmer knob (D). You can have any setting between full brightness
and the led off. The heatsetting will remain the same.
To turn off the power the Standby Switch (Switch 1) must beturned
'OFF'.
Initializing the Remote Control
Note: The remote control is packed separately in the carton.
1.
Slide open the battery cover on the back of the remote
transmitter.
2.
Install the AAA batteries into the remote control (see
Fig. 3).
3.
Replace battery cover.
Dispose of batteries in the proper manner according to Provincial and
local regulations. Any battery may leak electrolyte if mixed with a different
battery type, if inserted incorrectly, if all the batteries are not replaced
at the same time, if disposed of in a fire or if an attempt is made to
charge a battery not intended to be
The product can be controlled both manually and by remote control.
Remote Control Operation
Warning: It takes some time for the receiver to respond to the transmitter.
Do not press the buttons more than once within two seconds for
correct operation. On the control panel, switch 1 must be in the 'ON'
position in order for the PCB to operate.
Setting
Flame effect
Flame effect and heat
By continuously pressing the 'I' button the fire will cycle between flame
effect and flame effect plus heat.
To turn off any of the settings press the
The remote control may be placed, when not in use, in the wall-mounted
holster provided (see Fig. 3).
recharged.
Operation
Press 'I' button once
Press 'I' button again
button once.
Advertisement
