Torque Values; Tires; Lubrication; Electrical System - HUSTLER Super104 Operator's Manual

Table of Contents

Advertisement

in the engine and under the seat platform areas; minute dust
particle are abrasive to close-tolerance engine and hydraulic
assemblies.
Inspect mower daily for grass clippings and wire and string
tangles. The underside of the mower deck will collect a build-up
of grass clippings and dirt, especially when grass is wet or has
high moisture content. This build-up will harden, restricting
blade and air movement and will probably show a poorer quality
of cutting. Therefore it should be removed routinely.
To do this it will be necessary to raise and block the deck
using jack stands or blocks, in the full up position and scrape the
build-up from underneath.
Some repairs require the assistance of a trained service
mechanic and should not be attempted by unskilled personnel.
Consult your Hustler
®
service center when assistance is needed.

Torque Values

WARNING
Particular attention must be given to tightening the drive
wheel lug nuts and blade spindle bolts. Failure to cor-
rectly torque these items may result in the loss of a wheel
or blade, which can cause serious damage or personal
injury.
Torque values are given below:
Wheel (lug) nuts . . . . . . . . . . . . . . . . . 70 . . . . . . . . 95
Blade spindle bolt top . . . . . . . . . . . . . 70 . . . . . . . . 95
Blade spindle bolt bottom . . . . . . . . . . 118 . . . . . . . . 160
Wheel motor nut . . . . . . . . . . . . . . . . . 230 . . . . . . . . 312
Lug nuts only - It is recommended that these be checked after
the first 2 hours of operation, initially, every 50 hours and
following removal for repair or replacement.
For all other torques refer to the mower's General Service
Manual for standard torque chart. See Product Literature
section for ordering information.
For engine torque values, see engine owner's manual.

Tires

It is important for level mowing that the tires have the same
amount of air pressure. The recommended pressures are:
Drive wheels . . . . . . . . . . . 15-20 psi (103-138 KPa)
Front wheels . . . . . . . . . . . 20-25 psi (138-172 KPa)
If you wish to use non-pneumatic tires on your Hustler
mower the tires must be an approved tire purchased from
Hustler
®
Turf Equipment. Warranty claims will be denied on
any mower equipped with unapproved non-pneumatic tires.

Lubrication

Use SAE multi-purpose grease.

Electrical System

The electrical system for this mower is a 12 volt, negative
REV F
Ft-lbs.
N-m
®
4-2
ground.
When a replacement battery is required refer to the existing
battery and replace it with a battery with the same
specifications. The battery specification is listed below:
BCI group 45 with 480 or better cranking AMP rating.
A maintenance-free battery is recommended. Otherwise,
follow battery manufacturer's maintenance, safety, storing and
charging specifications.
WARNING
Battery posts, terminals, and related accessories contain
lead and lead compounds, chemicals known to the State
of California to cause cancer and reproductive harm.
Wash hands after handling.
WARNING
Charge batteries in an open well ventilated area, away
from sparks and flames. Unplug charger before connect-
ing or disconnecting from battery. Wear protective cloth-
ing and use insulated tools.
WARNING
• Avoid skin and clothing contact with battery acid.
• Always wear eye protection when checking the bat-
tery, acid can cause serious injury to skin and eyes.
If contact occurs, flush area with clean water and
call physician immediately. Acid will also damage
clothing.
• Do not drink the battery electrolyte.
• Do not allow open flame near the battery when
charging.
• Hydrogen gas forms inside the battery. This gas is
both toxic and flammable and may cause an explo-
sion if exposed to flame. Always remove the nega-
tive ground first and replace it last.
• Do not overfill battery.
• Electrolyte may overflow and damage paint, wiring
or structure. When cleaning the battery, use soap
and water. Be careful not to get soap and water into
the battery. Clean the battery terminals with a solu-
tion of four parts water and one part baking soda
when they become corroded.
604345

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Super 104

Table of Contents