Control Board Connections - Mighty Mule Wireless Gate Entry Intercom Installation Instructions Manual

Step 2: For hard-wired communication between the keypad and gate opener, using 16 gauge
(AWG) stranded, direct burial, low voltage wire (part no. RB509) strip the wires back 3/16"
and attach the wires to the terminal block marked RELAY OUTPUT on the keypad control
board as shown to the right. Connect the other end to the opener's control board as shown in
Control Board Connections section below.
To wire the power supply to the keypad, attach the wires to the AC/
DC POWER IN terminal on the keypad control board as shown
to the right. Connect the other end to the opener's battery - one
end to the POSITIVE (RED) pole and the other to the NEGA-
TIVE (BLACK) pole.
NOTE: For a hard-wired application
the jumper between the two terminals
on the keypad control board must be
connected (ON) as shown. This will
disable the 318 MHz RF transmitter.
Step 3: Slide the keypad into the cover and secure with the small screws provided.
CALLING GRANTED
1 2 3
ABC DEF
4 5 6
GHI JKL MNO
Step 4: Turn the power to the opener OFF. Remove the opener control board cover and feed enough of the low
8 9
7
TUV WXY
PRS
0
voltage wire from the keypad through a strain relief to reach the gate opener control board terminals.
STATUS
PROGRAM
CALL
Step 5: Attach the wires from the keypad to the opener control board terminal blocks as shown below.
Step 6: Replace the control board cover and turn the power switch ON. Test the keypad by entering 1 2 3 4.
Step 7: Program your 'Personal Master Code' and any additional entry codes (for a total of 25 entry codes).
See Programming the Keypad section.

Control Board Connections

NOTE:
If your control board doesn't look like any of these diagrams, please call GTO Technical Service at 1-800-543-1236 or
850-575-4144 for additional support.
PRO-1000, PRO-SL1000 and Old Mighty Mule
Control Boards
ALARM
Connect #2 wire from the
RELAY OUTPUT terminals
on the keypad to the GRN
terminal on the gate opener
control board.
#2
#1
Mighty Mule 500 & 502
Control Boards
COM COM
Connect #2 wire from
the RELAY OUTPUT
terminals on the keypad
to the COM terminal on
the gate opener control
board.
GTO/PRO DC Powered PRO-SW3000
and PRO-SW4000 Control Boards
Connect #2 wire from
the RELAY OUTPUT
terminals on the keypad
to the COM terminal on
the gate opener control
board.
SEQ1
SEQ2
LEARN
R B G
ACCESSORY RCVR
Connect #1 wire from the
RELAY OUTPUT terminals on
the keypad to WHT terminal on
the gate opener control board.
GRN BLK RED
RECEIVER
Connect #1 wire from the
RELAY OUTPUT terminals on
the keypad to CYCLE terminal on
the gate opener control board.
#1
#2
�8
��� ��� ��2
��M ��M GRN B�K R�D
RECEIVER
Connect #1 wire from the
RELAY OUTPUT terminals on
the keypad to CYCLE terminal on
the gate opener control board.
#1
#2
Mighty Mule 350 Control Board
LINK
Connect #1 wire from the
RELAY OUTPUT terminals
on the keypad to CYCLE
terminal on the gate opener
control board.
GEN-3 (Blue) Control Boards
Connect #2 wire from the
RELAY OUTPUT terminals
on the keypad to the COM
terminal on the gate opener
control board.
GTO/PRO GP-SL100 and GP-SW100
Control Boards
Connect #1 wire from the
RELAY OUTPUT
terminals on the keypad to
CYCLE terminal on the
gate opener control board.
3
+
0
–
1 2 3 4 5 6 7 8 9
RELAY AC/DC
OUTPUT POWER IN
Power Supply from
# 1 # 2
Opener Battery
Hard-wire from Gate Opener
RECR
Connect #2 wire from the RELAY
OUTPUT terminals on the keypad
to the COMMMON terminal on
the gate opener control board.
#2
#1
RECEIVER
CONTROL INPUTS
ALM
GTO RCVR.
Connect #1 wire from the RELAY
OUTPUT terminals on the keypad
to CYCLE terminal on the gate
opener control board.
#1
#2
Connect #2 wire from the
RELAY OUTPUT terminals
on the keypad to the COM
terminal on the gate opener
control board.
#2
#1