SAFETY INFORMATION To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. Follow all instructions printed on unit chassis for proper operation. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS PACKAGE CONTENTS ...............1 Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. INTRODUCTION & FEATURES ..........2 Please keep the following in mind as you unpack and install this SPECIFICATIONS ...............
INTRODUCTION The HD-88LA is high-performance 8x8 matrix routing switcher for HDMI signals. This switcher supports data rates up to 6.75 Gbps, enabling 1080p HDMI formats and UXGA/WUXGA/DVI resolution to any HD display. High Definition Digital signals can be selected and distributed to any (8) outputs simultaneously.
FRONT PANEL FRONT PANEL POWER SWITCH The power switch turns the unit on and off. The LCM will illuminate red to indicate that the switcher is ON and is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked.
Page 7
FRONT PANEL FRONT PANEL FUNCTION KEY - ALL Disables (mute) video on all destinations OR Selects the same source to all destinations. Option 1 - Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video selected. Option 2 - Press ALL followed by Source 1 thru 8.
Page 8
FRONT PANEL FRONT PANEL FUNCTION KEY - MEMORY The system will show store presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location. - Configure desired matrices.
REAR PANEL REAR PANEL DC POWER INLET The Switcher is fitted with a DC power plug input connector. Ensure Power Jack: that the used is of an approved type and is of sufficient current DC Jack - Inner OD ᴓ 2.1mm (+ ) carrying connector capacity with the correct voltage and connector Outside OD ᴓ...
TYPICAL APPLICATION INSTALLING DIAGRAM Sample connection using IR Transmitters and IR Receiver to control a projector via HDBaseT™ Transmitter and HDBaseT™ Receiver. NOTE: 1. IR Control Projector Over HDBaseT™ Extender: Use HDBaseT™ Transmitter & HDBaseT™ Receiver 2. Audio Input : Uspport DVI Audio input. 3.
Page 11
TYPICAL APPLICATION INSTALLING DIAGRAM Sample connection using DVI & Audio input and link to the AUDIO Amplifier via SPDIF digital signal output. NOTE : 1. Use DVI and Audio Input via DVI Player Device. 2. HDMI display support DVI input via HDMI HDTV Support DVI input 3.
REMOTE CONTROL Before making any connections to the switcher. Observe the following: > Ensure the mains voltage supply matches the label on the > Connect all audio video sources and destination equipment supplied plug-pack (+/- 10%) > Power up all source and destination audio-visual sources >...
Page 13
REMOTE CONTROL IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD) HOW TO SETUP IR CODES : Model number : HD-88LA CUSTOM CODE : 38C7 POWER ON : 38C7 A15E POWER OFF : 38C7 A25D ALL : 38C7 B04F OFF :...
IR ExTENDER 1. ANI-100 IR 300M Receiver Switcher IR EXT. In Cable (3C) IR Receiver (ANI-100) Distance: Max.300M IR PN#: ANI-XXXX R oHS /95/E C INP UT R S -232 IR E XT. in DC 12V IR Rx RS - 232 IR EXT .
EDID FUNCTION EDID FUNCTION SETUP EDID setup To change the EDID setup Step 1. Press the EDID button The display will show the currently selected EDID mode Step 2. Press SOURCE #1 or #2 button row The button will flash blue and the display will show the current Embedded EDID Status.
Page 16
EDID FUNCTION NOTE : The already learned EDID cannot be modified. You can only rebuild a new Learning EDID. For example: When the Source has “Learned” the EDID data from a destination, It will save that EDID information into EPROM and the EDID data cannot change.
Page 17
EDID FUNCTION EDID FUNCTION : LEARNING Learning EDID Single to Single Example : Learn Destination #8 EDID To Source #5. The button will flash blue and the display will show the current Embedded EDID Step 1. Press the EDID button Status.
Page 18
EDID FUNCTION AUTO MODE definition Common Resolution and Audio Switcher will find highest common Resolution and Audio from all destination EDID to link Source. Example for single source Destination > press #1 and then Source > press #1 Destination device #1 will set to the highest common resolution and Audio of source #1 Example for multiple sources Destination device #1, #2, #3 will be set to the highest common resolution and Audio available and source device #1 will output this same resolution.
ETHERNET SERIAL INTERFACE ETHERNET SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V2.0 For a complete list of commands, please reference external document extended Ethernet Protocol Instruction Manual. Example of the commanded string to route Input 3 to Output 4 OUTPUT04 03;...
RS-232 SERIAL INTERFACE RS-232 SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V2.0 For a complete list of commands, please reference external document extended RS-232 Protocol Instruction Manual. Example of the commanded string to route Input 3 to Output 4 OUTPUT04 03;...
Page 22
GUI INTERFACE 1B: Supports routing using Cross points...
Page 23
GUI INTERFACE 2: Select different matrix sizes...
Page 24
GUI INTERFACE 3: Support COM ports 1 thru 4...
Page 25
TERMS AND CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NEUVIDEO, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions.