Related Manuals for A-Neu Video ANI-MODZ8
Summary of Contents for A-Neu Video ANI-MODZ8
- Page 1 ANI-MODZ ANI-MODZ Series: Modular Matrix Switcher ® ™ ™ A-NeuVideo.com Frisco, Texas 75034 (469) 277-7606 AUDIO / VIDEO MANUFACTURER...
-
Page 2: Safety Information
SAFETY INFORMATION To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. Follow all instructions printed on unit chassis for proper operation. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. Keep unit protected from rain, water and excessive moisture. -
Page 3: Table Of Contents
SPECIFICATIONS ................. 3 • Always follow basic safety precautions to reduce the risk of fire, ANI-MODZ8 ...................7 electrical shock and injury to persons. FRONT PANEL OPERATION ..........7 • To prevent fire or shock hazard, do not expose the unit to rain, BACK PANEL OPERATION ............ -
Page 4: Introduction
Matrix to their requirements by simply adding or removing the input or output modules as required. The Modular Matrix is supplied with dual removable internal power supply units, (Except the ANI-MODZ8 which has only one PSU) which allow for easy inspection and maintenance. -
Page 5: Specifications
NEUVIDEO SPECIFICATIONS Main Units ANI-MODZ8 GENERAL Input Modular Slots Output Modular Slots (1) (8) HDMI or DVI or CAT5e/6/7 or VGA Output Channels (8) HDMI or DVI or CAT5e/6/7 Input Channels (dependent on module configuration) (dependent on module configuration) Power Supply... - Page 6 NEUVIDEO SPECIFICATIONS Main Units ANI-MODZ16 GENERAL Input Modular Slots Output Modular Slots (2) Input Channels (16) HDMI or DVI or CAT5e/6/7 Output Channels (16) HDMI or DVI or CAT5e/6/7 or VGA (dependent on module (dependent on module configuration) configuration) Power Supply (2) AC 110~240V 50/60Hz Installation Rack Mountable...
- Page 7 NEUVIDEO SPECIFICATIONS Main Units ANI-MODZ32 GENERAL Input Modular Slots Output Modular Slots (4) Input Channels (32) HDMI or DVI or CAT5e/6/7 Output Channels (32) HDMI or DVI or CAT5e/6/7 or VGA (dependent on module (dependent on module configuration) configuration) Power Supply (2) AC 110~240V 50/60Hz Installation Rack Mountable...
- Page 8 NEUVIDEO SPECIFICATIONS ANI-MODz signal card (changeable cards) The ANI-MODZ series input and output cards for installation into the modular matrix switcher chassis are classified into the following models. ANI-MODZ Input cards ANI-MODZ Output cards MODELS INPUTS SIGNAL FORMAT MODELS OUTPUTS SIGNAL FORMAT ANI-IN-5P HDBaseT...
-
Page 9: Ani-Modz8
NEUVIDEO ANI-MODZ8 Front Panel Operation ANI-MODZ8: The front panel of ANI-MODZ8 is shown below. LCM: Displays the setting information of each input/output and other setting information according to the selected mode. IR WINDOW: Accepts the IR remote control signal for the matrix only. -
Page 10: Back Panel Operation
NEUVIDEO ani-modz8 BACK Panel Operation ANI-MODZ8: The back panel of the ANI-MODZ8 is shown below. Note: The above panel is an example of 8x8 HDMI configuration. OUTPUTS 1~8: Install an Output module as required for connection to up to (8) displays (TVs or monitors) or CAT5e/6/7 outputs or compatible HDBaseT receivers. -
Page 11: Ani-Modz16/Ani-Modz32
NEUVIDEO ani-modz16/ani-modz32 Front Panel Operation ANI-MODZ16/ANI-MODZ32: The front panel for both the ANI-MODZ16 and the ANI-MODZ32 is shown below. LCM: Displays the setting information of each input/output and other setting information according to the selected mode. IR WINDOW: Accepts the IR remote control signal for the matrix only. -
Page 12: Rear Panel Operation Ani-Modz16
NEUVIDEO ani-modz16 back Panel Operation ANI-MODZ16: The back panel for the ANI-MODZ16 is shown below. Note: The above panel is an example of 16x16 HDMI configuration. OUTPUT 1~16: Install up to (2) Output modules as required for up to (16) displays (TVs or monitors) or CAT5e/6/7 outputs for compatible HDBaseT receivers. -
Page 13: Rear Panel Operation Ani-Modz32
NEUVIDEO ani-modz32 BACK Panel Operation ANI-MODZ32: The back panel for the ANI-MODZ32 is shown below. Note: The above panel is an example of the 32x32 HDMI configuration. OUTPUT 1~32: Installs up to (4) Output modules as required for up to (32) displays (TVs or monitors) or CAT5e/6/7 outputs for compatible HDBaseT receivers. -
Page 14: Remote Control
NEUVIDEO Remote Control Remote Control POWER: ON/OFF button OUTPUT: Output port button INPUT: Input port button ENTER: Press to confirm the present input/output selection CLEAR: Press to clear the present input/output selection Channels should be entered using two digits. For Example: Entering channel 2 should be “02” To Enter a Cross Point: Enter the Output channel, then Input channel, followed by ENTER For Example: To route Input 3 to Output 5... -
Page 15: Input & Output Modules
NEUVIDEO Input & Output Modules Input Modules ANI-IN-5P 8 Port HDBaseT Input Module ™ SPECIFICATIONS Video Bandwidth 300MHz/10.2Gbps Features HD Video/Audio, PoC, Ethernet, IR/RS-232 Pass Thru Input Ports (8) CAT5e/6/7, (1) LAN Ethernet Speed 100Mbps Video Resolutions PC: VGA~WUXGA HDTV: 480i~1080p@60Hz & 4K2K@30Hz IR Frequency 30~50Hz Audio Transmission... - Page 16 NEUVIDEO Input & Output Modules Input Modules ANI-IN-DV 8 Port DVI Input Module SPECIFICATIONS Video Bandwidth 225MHz/6.75Gbps Input Ports (8) DVI Video Resolutions PC: VGA~WUXGA@60 (RB) HDTV: 480i~1080p@60Hz Audio Transmission LPCM7.1CH, Dolby TrueHD, Dolby Digital Plus, DTS-HD Master Audio (32~192KHz Fs sample rate) Power Consumption ANI-IN-VG 8 Port VGA Input Module...
-
Page 17: Output Modules
NEUVIDEO Input & Output Modules Output Modules ANI-OUT-5P 8 Port HDBaseT Output Module ™ SPECIFICATIONS Video Bandwidth 300MHz/10.2Gbps Features HD Video/Audio, PoC, Ethernet, IR, RS-232 Pass Thru Output Ports (8) CAT5e/6/7, (1) LAN, (8) IR Extender, (8) IR Blaster Ethernet Speed 100Mbps Video Resolutions PC: VGA~WUXGA... - Page 18 NEUVIDEO Input & Output Modules OUTput Modules ANI-OUT-4K 8 Port 4K HDMI Output Module SPECIFICATIONS Video Bandwidth 300MHz/10.2Gbps Output Ports (8) HDMI Video Resolutions PC: VGA~WUXGA HDTV: 480i~1080p@60Hz, 4K2K@30Hz Audio Transmission LPCM7.1CH, Dolby TrueHD, Dolby Digital Plus, DTS-HD Master Audio (32~192KHz Fs sample rate) Power Consumption ANI-OUT-HD 8 Port HDMI Output Module...
-
Page 19: Transmitter & Receiver Options
NEUVIDEO TRANSMITTER & RECEIVER OPTIONS TRANSMITTERS & RECEIVERS 1080P@60HZ/ MANUFACTURE EXTERNAL TYPE BODY TYPE RS-232 ETHERNET POC* UHD CABLE PART# AUDIO POWER LENGTH ANI-315XLR Receiver Stand Alone ü ü ü 1-WAY ü ------ ----- 60 / 35M ANI-315XLT Transmitter Stand Alone ü... -
Page 20: Connection Diagram
NEUVIDEO CONNECTION DIAGRAM Example Installation (32x32 HDMI Matrix) -
Page 21: Ir Cable Pin Assignments
NEUVIDEO IR Cable Pin Assignments Power IR Signal IR Signal Power Grounding... -
Page 22: Rs-232 Protocols
NEUVIDEO RS-232 Protocols MATRIX RS-232 CONTROL Definition Definition ► ◄ Baud Rate: 19200Bps Data Bit: 8bits Parity: None Stop Bit: 1 Flow Control: None... -
Page 23: Rs-232 & Telnet Commands
NEUVIDEO RS-232 & Telnet Commands COMMAND CODES FUNCTIONS Power on Power off OxIy Set Output (x=1~32) to Input (y=1~32) ALLOUT x Set all Outputs to Input (x=1~32) ACTIVE Report active I/O channels INDETECT Input channel detection indicator OUTDETECT Output channel detection indicator PORTSTATUS Reports all Output connection status HDCPON x... - Page 24 NEUVIDEO RS-232 & Telnet Commands COMMAND CODES FUNCTIONS IRMASKCPU x y z* Disable/enable (z=0/1) IR transmission from the IR ALL input on the CPU Control Board to the HDBaseT ™ Transmitter (x=src), Receiver (x=sink) or Output Module (x=out) on to the specified port (y=1~32/all). Example 1: “IRMASKCPU src all 0”...
-
Page 25: Telnet Control
NEUVIDEO Telnet Control Setup procedure for 4K2K UHD The default EDID setting, regardless of I/O cards, is 1080p@60Hz. Because EDID determines when a source can output a 4K2K signal, the matrix switcher must be told which source and display to use for EDID information exchange. These changes are done using the front panel of the matrix or Telnet. - Page 26 NEUVIDEO Telnet Control Before attempting to use the Telnet control, please ensure that both the Matrix (via the ‘LAN /CONTROL’ port) and the PC/Laptop are connected to the same active networks. To access the Telnet control in Windows 7, click on the “Start” menu and type “cmd” in the “Search” field, then press ENTER. • Under Windows XP go to the “Start”...
- Page 27 NEUVIDEO Telnet Control This will bring us into the unit which we wish to control. Type “help” to list the available commands. Type “IPCONFIG” to show all the IP configurations. To reset the IP, type “RSTIP” and to use a static IP, type “SETIP” (For a full list of commands, see Section RS-232 &...
-
Page 28: Web Gui Control
NEUVIDEO Web GUI Control On a PC/Laptop that is connected to the same active network as the Matrix, open a web browser and type the unit’s “IP address” on the web address entry bar. The browser will display the unit’s Status, Control and User Setting pages. Click on the “Control”... - Page 29 THIS PAGE IS INTENTIONALLY LEFT BLANK.
- Page 30 THIS PAGE IS INTENTIONALLY LEFT BLANK.
- Page 31 THIS PAGE IS INTENTIONALLY LEFT BLANK.
- Page 32 NEUVIDEO TERMS & CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NEUVIDEO, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions.