Preset - Denon DN-D4000 Operating Instructions Manual

ENGLISH
(3) 1 Track MEMO CLEAR [TrakM.Clr]
• To clear one memo data, select the track that you made MEMO. Then MEMO indicator lights up.
• Push the MEMO/PRESET button @4 to enable Memo clear function.
• When the track select knob o is pushed in MEMO CLEAR mode, the Memo data is cleared and the
MEMO indicator on the display turns off.
ALL Track MEMO CLEAR
• All memory data can be cleared.
• For instructions, see "⁄1 PRESET (15) Track Memo All Clear".
(4) Storing data in the memory [DiscM.Set]
• When MP3 disc is loaded, push the MEMO/PRESET button @4 .
• Turn the track select knob o to select the "DiscM.Set?".
• When the track select knob o is pushed, the disc information is stored.
(5) 1 Disc MEMO CLEAR [DiscM.Clr]
• To clear one memo data, load the MP3 disc that you stored information.
• Push the MEMO/PRESET button @4 to enable Memo clear function.
• When the track select knob o is pushed in MEMO CLEAR mode, the Memo data is cleared and the
MEMO indicator on the display turns off.
ALL Disc MEMO CLEAR
• All memory data can be cleared.
• For instructions, see "⁄1 PRESET (16) Disc Memo All Clear".
(6) MEMO FULL
• If the memory is full and no more data can be stored, "DiscM.Full", "TrakM.Full" message appears.
• In this case, you need to clear memory for space of new memos. (For instructions, see step (3), (5).)
NOTE:
• "TrakM.Ext" or "DiscM.Ext" is displayed if the"TrakM.Set", "TrakM.Clr" or "DiscM.Clr" operation is
performed for a disc stored on the other drive.
If this happens, load the disc in the other drive.
11

PRESET

1. Preset mode
q The preset mode is available when MEMO/PRESET button @4 is pushed for more than 1 second while
DN-D4000 is in Cue, pause or no disc mode.
w Turn the track select knob o to select the preset item.
e After selecting an item, push the track select knob o to select the preset data.
r To change other Preset items, repeat these steps (w, e).
t Push the MEMO/PRESET button @4 or CUE button !0 to exit from the Preset mode.
2. Preset items and data
The "*" mark next to the data indicates the default value.
(1) Auto Cue: Auto Cue search level.
A.Cue *** : OFF / -48* / -42 / -36 dB
(2) Brake Time: Set the operating time for the BRAKE mode.
Brake ***s : 0.5 / 1.0 / 1.5 / 2.0* seconds
(3) Relay mode function selection: The relay playback mode can be selected with the CONT./SINGLE
Relay : ON / OFF*
(4) EOM: Track end message start time.
EndMsg **s : OFF / 10* / 15 / 20 / 30 / 60 / 90 seconds
(5) Auto Close: Time for automatically closing disc holder.
A.Close **s : OFF / 10 / 30* / 60 seconds
(6) Sleep Mode: If no operation is performed in the pause or cue mode, the motor stops and the stop
mode is set after a specific amount of time.
Sleep **m : 10 / 20 / 30* minutes
14
button u.
(7) Digital Out:
DigOut : ON* / OFF
(8) Fader: Select 2-line type (Cue and Play) or 1 line type (Play and Pause).
Fader : 2Lin* / 1Lin
(9) Power On Play: Playback starts when the power is turned on if a disc is loaded.
A.Play : ON / OFF*
(10) Play List: Setting of whether or not to perform the play list.
P.List : ON / OFF*
(11) Disc Memo: Setting of whether or not to perform the MP3 disc memo.
D.Memo : ON* / OFF
(12) Single/Continuous: Select the play mode when the power is turned on.
PlayM. : Sing* / Cont
(13) Elapsed/Remain: Select the time mode when the power is turned on.
TimeM. : Elap* / Rema
(14) Pitch Range: Select the playing pitch range when the power is turned on.
P.Range**% : ±4 / ±10* /±16 %
(15) Track Memo All Clear: Clear all track MEMO data in the non-volatile memory. ("TrakM.Clr?")
q To clear all track MEMO data, push the track select knob and select "YES".
• "Clear OK?" flashes on the character display.
w Push the track select knob again and select "OK" to execute clearing all MEMO data.
• "Now Saving" is displayed on the character display while clearing.
e Once clearing is completed, "Complete!" is displayed.
(16) Disc Memo All Clear: Clear all disc MEMO data in the non-volatile memory. ("DiscM.Clr?")
q To clear all disc MEMO data, push the track select knob and select "YES".
• "Clear OK?" flashes on the character display.
w Push the track select knob again and select "OK" to execute clearing all MEMO data.
• "Now Saving" is displayed on the character display while clearing.
e Once clearing is completed, "Complete!" is displayed.
(17) Program All Clear: Clear all program play data in the non-volatile memory. ("ProgM.Clr?")
q To clear the program, push the track select knob and select "YES".
• "Clear OK?" flashes on the character display.
w Push the track select knob again and select "OK" to execute clearing the program.
• "Now Saving" is displayed on the character display while data clearing.
e Once clearing is completed, "Complete!" is displayed.
(18) Display the microprocessor version. ("xxxx" is a number.)
: SysVerxxxx* / RC Verxxxx
(19) Preset Clear: Set all the preset data back to the factory defaults. ("PresetInt?")
q To clear the PRESET data, push the track select knob.
• "Initial OK?" flashes on the character display.
w Push the track select knob again and select "OK" to start clear the preset data.
• "Now Saving" is displayed on the character display while data clearing.
e Once clearing is completed, "Complete!" is displayed.