Texecom Premier 8XP-W Installation Manual
  1. Manuals
  2. Brands
  3. Texecom Manuals
  4. Security System
  5. Premier Elite 8XP-W
  6. Installation manual

Texecom Premier 8XP-W Installation Manual

Hide thumbs Also See for Premier 8XP-W:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual

Installation Manual

Premier 8XP-W & Premier 32XP-W
INS467-2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Premier 8XP-W and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Texecom Premier 8XP-W

Summary of Contents for Texecom Premier 8XP-W

  • Page 1: Installation Manual

    Installation Manual Premier 8XP-W & Premier 32XP-W INS467-2...

  • Page 2: Table Of Contents

    Premier 8XP-W & 32XP-W Installation Manual 1. Contents Contents ......................2 Premier 8XP-W & 32XP-W ................4 Quick Start Guide.................... 5 System Design Considerations ..............6 Learning Devices ..................6 Placing Devices ................... 6 System Overview .................... 7 Mounting the Expander ..................9 Wiring ........................
  • Page 3 Premier 8XP-W & 32XP-W Installation Manual Device Status Indications ................31 Modes of Operation ..................32 Commission Mode ..................32 Expander....................32 Device Commission Mode ................. 32 Device Specific Functions ................32 Prestige XT-W & Prestige QD-W ..............32 ImpaqPlus-W ....................32 Impaq Contact-W..................

  • Page 4: Premier 8Xp-W & 32Xp-W

    The PREMIER 8XP-W & 32XP-W expanders can be used on any premier control panel; however certain features and functions are dependent on the version of panel firmware as detailed in the table below.

  • Page 5: Quick Start Guide

    Premier 8XP-W & 32XP-W Installation Manual 3. Quick Start Guide Connect Receiver to Control Panel Network & Leave Tamper Circuit Open. See Page 9 Check Panel Firmware Version Ricochet™ See Page 4 Ensure all Option Switches Legacy are off See Page 8...

  • Page 6: System Design Considerations

    Premier 8XP-W & 32XP-W Installation Manual 4. System Design Considerations To ensure correct setup and operation of the Wireless Network it is important that the following procedures are used when learning and placing devices. Learning Devices All devices should be learnt before they are placed in their final location. The expander should be in commission mode, please see page 32.This will ensure that they are registered on the receiver...

  • Page 7: System Overview

    Premier 8XP-W & 32XP-W Installation Manual 5. System Overview 1 2 3 4 1 2 3 4 1: Engineers Keypad Connection An engineer’s keypad (Premier LCD keypad and interface lead) can be temporarily plugged onto this connector to allow system programming and testing. (Functions dependent on Panel firmware version) Set the keypad address switches to all on.
  • Page 8 Premier 8XP-W & 32XP-W Installation Manual 5: Lid Tamper When open puts the system into commission mode and digitally attenuates the receiver signal by 6Db. 6: Programming LED’s Allows programming of devices directly to the receiver, in conjunction with the learn switch.

  • Page 9: Mounting The Expander

    Premier 8XP-W & 32XP-W Installation Manual Mounting the Expander Remove each screw cap by inserting a flat bladed screwdriver into the slot and turning anti- clockwise, excessive force is NOT required. Remove both of the cover screws and put them in a safe place along with the screw caps.

  • Page 10: Selecting An Address

    Premier 8XP-W & 32XP-W Installation Manual The networks are made up of four terminals incorporating power and data. To ensure correct operation, all four terminals on the device must be connected to the corresponding terminals on the control panel or previous device.

  • Page 11: Programming

    4.  When using the Premier 8XP-W it is only possible to learn devices to slots 1-8 on the expander. Slots 9-32 will still be shown in Ricochet Monitor, and on the keypad, however no devices can be learned to them.

  • Page 12: Deleting Devices

    Premier 8XP-W & 32XP-W Installation Manual       /             /     Use keys 0 - 9 to enter the   ...

  • Page 13: Premier 24 V7.00-V8.23, 48/88/168 V7.00 - V8.14, 640 V7.00-V8.15

    Premier 8XP-W & 32XP-W Installation Manual Premier 24 V7.00-V8.23, 48/88/168 V7.00 – V8.14, 640 V7.00-V8.15 Option Switch Settings For V7.00-V8.11 of firmware switch 1 2 & 3 should be ON for all panels.  For Versions prior to V7.40 on the Premier 24, Learned devices should be mapped to zones 9-24 only, it is not possible to map to Zones 1-8.

  • Page 14: Deleting Devices

    Premier 8XP-W & 32XP-W Installation Manual Follow these instructions to learn devices to the control panel AFTER they have been learnt to the receiver.       /         ...

  • Page 15: Premier 412/816 V11.10 & Later, Premier 832 V4.10 & Later

    Premier 8XP-W & 32XP-W Installation Manual Premier 412/816 V11.10 & Later, Premier 832 V4.10 & Later Follow these instructions to learn devices to the system, once completed follow the relevant section of the control panel manual to programme zones and user attributes.

  • Page 16: Removing Detectors

    Premier 8XP-W & 32XP-W Installation Manual Removing Detectors If a detector is no longer required it must be unassigned from the system. To remove a detector from a zone, proceed as follows: Enter Engineers code  Then press then ...
  • Page 17 Premier 8XP-W & 32XP-W Installation Manual Premier SmartKey™ are assigned to users as follows: Enter Engineers code  Then press then          Enter User        Number ...

  • Page 18: Removing Premier Smartkey

    Premier 8XP-W & 32XP-W Installation Manual Removing Premier SmartKey™ If a Premier SmartKey™ is no longer required it must be unassigned from the system. To remove a Premier SmartKey™ from a user, proceed as follows: Enter Engineers code  Then press then ...

  • Page 19: Premier 412/816 V10.5 - V11.07 & Premier 832 V3.50.-.V4.07

    Premier 8XP-W & 32XP-W Installation Manual Premier 412/816 V10.5 – V11.07 & Premier 832 V3.50.-.V4.07 Follow these instructions to learn devices to the system, once completed follow the relevant section of the control panel manual to programme zones and user attributes.

  • Page 20: Removing Detectors

    Premier 8XP-W & 32XP-W Installation Manual Select engineer’s mode by entering the engineer code followed by / then . Enter  to select the Assign Radio Device menu, if an error tone is generated then the receiver is not installed or configured correctly.

  • Page 21: Learning Premier Smartkey

    Premier 8XP-W & 32XP-W Installation Manual Learning Premier SmartKey™ All Premier SmartKey™ must be assigned to one of the available users on the system. The users available will vary depending on the control panel: Control Panel Available Users Premier 412...

  • Page 22: Removing Premier Smartkey

    Premier 8XP-W & 32XP-W Installation Manual Removing Premier SmartKey™ If a Premier SmartKey™ is no longer required it must be unassigned from the system. To remove a Premier SmartKey™ from a user, proceed as follows: Enter Engineers code  Then press then ...

  • Page 23: Learning Devices Directly To The 8Xp-W & 32Xp-W

    Premier 8XP-W & 32XP-W Installation Manual Learning Devices directly to the 8XP-W & 32XP-W  this is only available in legacy mode. All devices can be learnt directly to the receiver. Device attributes cannot be changed when learning devices in this mode, all devices will use their factory default.

  • Page 24: Using The Engineers Keypad

    Premier 8XP-W & 32XP-W Installation Manual Using the Engineers Keypad The Engineers Keypad can be connected directly to the expander, and has the following features & functions.  Learning & Deleting devices is only available in Legacy Mode Device list The device list has the following features:- 1.
  • Page 25 Premier 8XP-W & 32XP-W Installation Manual 2. Delete Devices      /          /          /      ...
  • Page 26 Premier 8XP-W & 32XP-W Installation Manual 3. Change Device attributes Device attribute changes should be saved by either pressing the /  key after each device change, or by pressing the /  key after scrolling through the devices and making multiple changes.
  • Page 27 Premier 8XP-W & 32XP-W Installation Manual 4. Change Premier SmartKey™ attributes  Premier SmartKey™ attribute changes should be saved by either pressing the key after  each Premier SmartKey™ change, or by pressing the key after scrolling through the devices and making multiple changes.

  • Page 28: Update Devices

    Premier 8XP-W & 32XP-W Installation Manual Update Devices Used to immediately update devices (NOT Premier SmartKey™) attributes when changed in the Device List menu.      /          ...

  • Page 29: Walktest Mode

    Premier 8XP-W & 32XP-W Installation Manual Walktest Mode Used to initiate & stop Walktest Mode      /         /        Wh en u pd atin g d evic es a mes s ag e is s en t to all to ena ble th e LE D’...

  • Page 30: System Status

    System Status Shows various System Details 1.   = Receiver connected to Premier Network correctly  = Not Connected 2.  = Firmware version of the Premier 8XP-W/32XP-W 3.  = Receiver is being Jammed 4.  = Commission Mode 5.

  • Page 31: Device Status Indications

    Premier 8XP-W & 32XP-W Installation Manual Device Status Indications On the top line of the display the following may be seen depending on the device and status:-  = all devices Front Tamper       ...

  • Page 32: Modes Of Operation

    Premier 8XP-W & 32XP-W Installation Manual 7. Modes of Operation Commission Mode Expander The expander has a Commission Mode, which when operated ensures secure communications with devices on the system. Commission Mode is automatically enabled when the expander is in tamper.

  • Page 33: Impaq Contact-W

    Premier 8XP-W & 32XP-W Installation Manual Impaq Contact-W The Impaq Contact-W has 3 additional inputs labelled MAG 1 COM MAG 2, these inputs can be used for any N/C device. If the Reed switch is disabled the device can be used as a transmitter for any device wired into one of the two inputs.

  • Page 34: System Attributes

    Premier 8XP-W & 32XP-W Installation Manual 8. System Attributes Polling Polling occurs between the devices and the receiver at a pre-determined interval of 15 minutes. This helps to conserve battery life. Poll intervals are set to 4 minutes when the system is in Commission Mode.

  • Page 35: Premier Smartkey

    Premier 8XP-W & 32XP-W Installation Manual Premier SmartKey™ LED Indications Premier SmartKey™ Status LED The Status LED has four colours. This LED cannot be disabled. 1. Pink = Power Up or Down 2. Green = Successful communication with the system 3.

  • Page 36: Auxiliary Functions

    Premier 8XP-W & 32XP-W Installation Manual Auxiliary Functions The Premier SmartKey™ can also be used to activate auxiliary devices from the control panel outputs. The function keys should first be enabled either from the Engineers Keypad see page 27, or RICOCHET™...

  • Page 37: Arm Fail Indication

    Premier 8XP-W & 32XP-W Installation Manual S martKey s tatus LE D AR M PAR T AR M DIS AR M P O WE R (hold 2 s ecs) Alarm status LE D’s DIS AR ME D PAR T AR ME D...

  • Page 38: Battery Considerations

    Premier 8XP-W & 32XP-W Installation Manual Battery Considerations Battery life for all devices will be determined by system complexity, the number of devices that hop, and the use of the Always Awake mode. In a typical system, battery life should be up to 4 years for devices, hopping devices should achieve between 2-3 years.

  • Page 39: Specifications

    Premier 8XP-W & 32XP-W Installation Manual 9. Specifications Electrical 10 - 13.7VDC Operating Voltage Current Consumption <120mA Network 4-wire standard 7/0.2 alarm cable up to 250m. Star, Daisy Chain or any combination. Outputs 1 - 8 Not Used -10°C (+14°F) to +50°C (+122°F) Operating Temperature -20°C (-4°F) to +60°C (+140°F)

  • Page 40: Standards

    Warranty All Texecom products are designed for reliable, trouble-free operation. Quality is carefully monitored by extensive computerised testing. As a result the Premier 8XP-W & 32XP-W expander is covered by a two-year warranty against defects in material or workmanship. As the Premier 8 XP-W & 32XP-W expander is not a complete alarm system but only a part thereof, Texecom cannot accept responsibility or liability for any damages whatsoever based on a claim that the Premier 8 XP-W &...

  • Page 41: Notes

    Premier 8XP-W & 32XP-W Installation Manual Notes...

  • Page 42: Notes

    Premier 8XP-W & 32XP-W Installation Manual Notes...

  • Page 43: Notes

    Premier 8XP-W & 32XP-W Installation Manual Notes...

  • Page 44: Technical Support

    Texecom Limited, Bradwood Court, St. Crispin Way, Haslingden, Lancashire BB4 4PW, England. Technical Support: UK Customers Tel: 08456 300 600 (Calls charged at local rate from a BT landline. Calls from other networks may vary.) International Customers Tel: +44 1278 686197 Email: techsupport@texe.com...

This manual is also suitable for:

Premier 32xp-w

Table of Contents

Save PDF