1. Manuals
  2. Brands
  3. Clarion Manuals
  4. Car Receiver
  5. VRX633R
  6. Installation and wire connection manual

Clarion VRX633R Installation And Wire Connection Manual

Hide thumbs Also See for VRX633R:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual & Installation Manual
1.

BEFORE STARTING

1. This set is exclusively for use in cars with a
negative ground 12 V power supply.
2. Read these instructions carefully.
3. Be sure to disconnect the battery " " termi-
nal before starting. This is to prevent short
circuits during installation. (Figure 1)
2.

PACKAGE CONTENTS

1 Main unit
2 Manuals
Owner's manual & Installation manual
Warranty card
3 Power supply lead
Flat head screw (M5 × 8)............................4
Sems hexagonal bolt (M5 × 8)....................5
VRX633R
Installation and Wire connection manual
Contents
1. BEFORE STARTING ................................................................ 47
2. PACKAGE CONTENTS ............................................................ 47
3. GENERAL CAUTIONS ............................................................. 48
4. CAUTIONS ON INSTALLATION .............................................. 48
5. INSTALLING THE MAIN UNIT ................................................. 49
6. REMOVING THE MAIN UNIT .................................................. 51
7. CAUTIONS ON WIRING .......................................................... 51
8. WIRE CONNECTION ............................................................... 52
9. SAMPLE SYSTEMS ................................................................ 54
6 Universal mounting bracket
7 Remote control unit
8 Battery
9 Outer Escutcheon
0 DCP Case
Cord clamp
Spacer
Special screw
(for remote control unit)
47
VRX633R

Advertisement

Table of Contents
loading

Related Manuals for Clarion VRX633R

Summary of Contents for Clarion VRX633R

  • Page 1: Table Of Contents

    VRX633R Installation and Wire connection manual Contents 1. BEFORE STARTING ..............47 2. PACKAGE CONTENTS ............47 3. GENERAL CAUTIONS ............. 48 4. CAUTIONS ON INSTALLATION ..........48 5. INSTALLING THE MAIN UNIT ..........49 6. REMOVING THE MAIN UNIT ..........51 7.

  • Page 2: General Cautions

    For tough dirt, apply a little cold or dealer or an authorized CLARION service warm water to a soft cloth and wipe off the centre.

  • Page 3: Installing The Main Unit

    3. Insert the main unit into the universal mount- 1) Some car models require special mounting kits ing bracket until it locks. for proper installation. Consult your Clarion dealer for details. 4. Mount the outer escutcheon so that all the 2) Fasten the front stopper securely to prevent hooks are locked.
  • Page 4 Note 1: In some cases, the centre panel may re- Note 2: If a hook on the installation bracket inter- quire some modification (trimming, filling, feres with the unit, bend and flatten it with a etc.). nipper or a similar tool. VRX633R...

  • Page 5: Removing The Main Unit

    4. When any fuse is to be replaced, pull out the Figure 10 fuse (15A) at the rear of the main unit and put in a new one (Fig.10). CAUTION After the connection, fix the lead by a clamp or insulation tape for protection. VRX633R...

  • Page 6: Wire Connection

    “triggered audio mute for cellular telephones” function. ∗4:Use the attached extension lead when necessary. ∗5:When connecting CCD CAMERA, be sure to connect RCA as well as the 8-pin Mini-Din video jack. Note : Before making any installation, disconnect the car battery - (negative) cable. VRX633R...
  • Page 7 NAVI) and the RGB terminal of the main unit. For detailed information, refer to the operating in- structions provided with car navigation equipment. When the NAVI is connected, the CCD camera cannot be connected. When the Clarion NAVI is to be connected, set the INPUT to the NAVI posi- tion.

  • Page 8: Sample Systems

    (TTX7502z/ Navigation System TTX7503z) (NAX9500E) CeNET Cable ∗To enable the correct input, it is necessary (included the DAB tuner) to configure the VRX633R as described on page 39. RDI OUT DAB Tuner (DAH913/DAH923) CeNET Cable (included the Changer) Ferrite clamp...
  • Page 9 (CCA-389, sold separately) (NAX9500E) ∗To enable the correct input, it is CeNET Cable (included the DAB tuner) necessary to configure the VRX633R as described on page 39. ∗The rear monitor displays TV/VTR images only. Images from the DVD RDI OUT DAB Tuner changer cannot be displayed.
  • Page 10 CeNET Cable (included the CCD camera) (included the DAB tuner) CCD camera ∗To enable the correct input, it is necessary to configure RDI OUT the VRX633R as described DAB Tuner on page 39. (DAH913/DAH923) CD Changer CeNET Cable (CDC655z/655Tz/1255z/ (included the Changer)

Table of Contents