Electrical Connection - Whirlpool 27 Electric Built-in Combination Installation Instructions

grounding wire). The fiedble, armored
cable extending from the appliance
should be connected dire&+ to the
iunctbn box.
E
Locate the junction box to
m allow as much slack CIS oossible
between the Junction box an'd ihe
appliance so that the oven con be
moved if servicing is ever necessoly.
Do Not cut the conduit.
F
A U.L:listed conduit connector must
l
be provided at the Junction box.
G
ii is the personal responsibility
. and obligation of the
customer to contact a quoliWd
electWan to assure that me electial
installation b odequote and In
confomance VJim the Naiional
ElectrIcal Code ANWNFPA 7&k&&
edition.' and all local codes and
ordinances.
Copies of me standard listed may be
obtained from:
' National Fire Prdeclion Association
Botterymarch Pati
Quincy, Massachusetts 02269
H
A tiring diagram $ Included In
. the Tech
Sheet. The Tech Sheet
is located on bottom. behind the
lower vent grill.
Electrical
connection
Electrical Shock Hozord
* Eledrtcal ground is required on
this appliance.
- Do Not connect to the electrical
supply until appliance is
permanently grounded.
* Dtsconnecl power to the junction
box before making the electrical
connedion.
. This appliance must be
connected lo o grounded,
metallic. permanent wiring
system. or o grounding
connector should be connected
to the grounding terminal or wire
lead on Ihe appliance.
Failure to do so could result In Q
fire, personal injury or electrical
shock.
lhls appliance
Is manufactured
him
white (neutra0 power supply wire and (
cabInetconnected. ereen grounding
tie lwkbd together.
Connect the
appliance cable to the Jundon bow
throuah the U.L-llsted conduit
con&&tor. Complete elecirlcal
connection according to your
lnstotlatkn needs.
B. Where local codes
DO NOT permit...
Connecting the cabinet-grounding
conductor to the neuiral (white)
junction box wire:
Cab!+ horn
power wpply
J""t,lo"
I I
Cob,.
A: Where local codes
permit... .'- ., .+
Contiecttng the cablnel-grounding
condudor lo the neutral (whtte)
junction box wire:
Cabk horn
Jundlon
power supply
, ,
ct
es
1. Turn power supply off.
2. Connect three wires: green and
white appliance cable wires and the
white wire
in
the iunction box.
3. Connect the two black tires
together; then the two red wires
together. (See Figure 1.)
Now start...
With oven in kitchen.
1
Remove shlpping materials and
. protective film from microwove
oven and
oven.
Do Not remove the
loom shipping base d Ihb time.
Figure 2
from O"."
1. Turn power supply On.
2. Connect the tiie appliance
cable tire to the neutral (whiie) wire
in Junct!on box.
3. Connect the Iwo black tires
together; men me two red wires
together. (see
figure 2.)
4. Connect the grounding wire to o
grounded wire in the junction box or
to a grounded. copper cold water
3
Completely open oven door.
. Remove two oven door screws.
2
Remove and unwrap racks
. and omer parts from inside oven.
Remove the air grille taped to
me top
or side of oven.
5.
A separate copper grounding wire
(No.-10 minimum) MUST be connected
io a grounded metal cdd water pipe
by means of a clomp and then to the
external grounding connector screw.
Do Nd ground to a gas supply pipe OT
hol waler
plpe.
Do Not connect to
electrical suppk until appliance Ls
pemanentty grounded. (see Flgure 3.)
C. If connecting to a four-
wire electrical system...
Do Not connect the cabinet
grounding conductor lo the neutral
(white) Junction box wire.
Cabl. horn
POW.'IUPPlY
I I
Figure 4
cab!.
from 0°C."
1. Turn power supply ott.
2. Separate the green and white
appliance cable wires.
3. Connect the white oppllance
cable wire to the neutral (white) wire
in the junction box.
4. Connect the two black wires
together: then ihe hue red wires
together. (See Figure 4.)
5. Connect the green appliance
cable wire to the green grounding
wire in the Junction box.
Personal Injury Hazard
l
Use both hands to remove oven
door.
. Grasp onty the sides of the oven
door.
. Do Not use handle or any portion
ot the hont hame or him for lining.
. Because ot the weight ond she
of the oven, two or more people
ore needed to move and solety
install oven.
Failure to properly grasp the oven
door or to Iti7 oven property could
resutl in damage lo product or
personal injury.
4
Close oven door to me broil
. position. Grasp lhe skies of the
oven door and pull the door up and
off the hinges to remove. Set dmr
aside.
Before
moving oven acrass floor.
check thoi oven is on shipping
base or Me oven onto
cardboard or hardtird.
Failure to follow these instructions
may resuli in danoge to floor
coverinq.
5
Turn power supply off. Move
. oven close to final oosition.
Remove and discord shipping base,
cardboard or hardbwrd. Feed
appliance cable through opening in
cabinet. Make electlical conn@fions.
See Electrical requirements
and
ElecMcol connechon sections. Panels A
and 8.
Panel
B