Casio 5363 Operation Manual

MA1308-EA
Your watch may differ somewhat from the one shown in the illustration.
Some models may use a combination of hands and rotating disks to indicate
information. The word "hand" in this section is used to mean both analog hands
and rotating disks.
Second Hand
Stopwatch Minute Hand
Stopwatch functions
To adjust the time setting
When the second hand is at
12 o'clock, pull the
Click 2.
Rotate the
Crown
time setting.
Push the Crown back in.
Note
Take care that you set the correct AM
or PM time.
When changing the time, move the
minute hand four or fi ve minutes past
your fi nal setting, and then back it up
to the setting you want.
Crown Operations
Some water-resistant models (100 meters, 200 meters)
have a screw-in crown. When you need to perform a crown
operation, rotate it towards you to unscrew it. Then pull
the crown out. Avoid applying undue force when pulling.
The watch loses its water resistance while the crown is
unscrewed. After performing a crown operation, fully screw
the crown back in.
If your watch has a rotary bezel...
You can rotate the bezel to align its ▼ mark with the
minute hand. Then you will be able to tell how much
time has elapsed since aligning the ▼ mark.
Operation Guide 5363
Stopwatch 1/5-Second Hand
Hour Hand Minute Hand
A
Click 1
Crown
B
24-hour Hand
Day Indicator
To change the day indicator setting
Pull the out to Click 1.
Crown
Crown out to
Rotate the Crown
to change the
Push the back in.
Crown
Note
The day indicator setting uses a 31-
day month. Make adjustments for
months of shorter lengths.
Avoid changing the day indicator
setting between the hours of 9
p.m. and 1 a.m. Otherwise, the day
indicator may not change correctly at
midnight.
Current
Using the Stopwatch
The stopwatch measures elapsed time in 1/5 (0.2)-second increments up to
59 minutes, 59.8 seconds.
Elapsed time
A
Start
Split time
A
Click 2
Start
Two fi nishes
A
Start
Important!
Do not operate the stopwatch with the crown pulled out.
Note
The Stopwatch 1/5-Second Hand and Stopwatch Minute Hand move for the fi rst
12 hours of an elapsed time measurement. After that, they stop at 0 and they are
reset.
Correcting the 0 Positions of the Hands
Perform the following procedure if the stopwatch hands do not return to their 0 (zero)
positions when you reset the stopwatch.
to set the day.
Pull the
Crown
Hold down A for about two seconds.
The
Stopwatch Minute Hand
hand setting mode.
If the hand does not align with 12 o'clock, use the B button to adjust it.
Holding down B moves the current hand at high speed.
Hold down A for about two seconds.
The
Stopwatch 1/5-second Hand
second hand setting mode.
If the hand does not align with 12 o'clock, use the B button to adjust it.
Holding down B moves the current hand at high speed.
Crown
After all of the hands are the way you want, push the
Important!
Timekeeping stops while the crown is pulled out. Correct the current time setting
after performing the above operation.
Loosen
Specifi cations
Start
Accuracy: ±20 seconds average per month
Stopwatch: Measuring Capacity: 59'59.8" (60 minutes)
Measuring Unit: 1/5 (0.2) second
Measurements: Elapsed time; split time; two fi nishes
Elapsed time
Battery: One silver oxide battery (Type: SR927SW)
Battery Life: Approximately 5 years (2 hours stopwatch operation per day)
Low Battery Indicator: Second hand moves in 2-second increments when power is low.
A A
A
Stop Re-start Stop
B A
B
Split Split release Stop
A B
B
Split Stop Split release
Display time of
First runner Second runner
second runner.
fi nishes. fi nishes.
Display time of fi rst
runner.
out to Click 2.
will perform one full rotation to indicate the minute
will perform one full rotation to indicate the
Crown
B
Reset
B
Reset
B
Reset
back in.
1