Using The Timer - Casio 3334 Operation Manual

Using Alarms and the Hourly Time Signal
You can set up to five independent daily alarms. An alarm sounds
for 10 seconds when an alarm time is reached.
The Hourly Time Signal causes the watch to beep every hour on
the hour.
Setting an Alarm Time
Alarm Number Graph
1.
In the Alarm Mode, use the
D D D button to scroll D D
through the alarm
numbers in the left dial
(A1 to A5) until the one
you want is displayed.
• The current alarm time setting
for the selected alarm will
appear in the bottom dial.
Alarm Time
– –:– – will appear instead of
the alarm time if that alarm is Alarm
Number
turned off.
Alarm1 Alarm2 Alarm3
(AL1) (AL2) (AL3)
Hourly Time Alarm5 Alarm4
Signal(SIG) (AL5) (AL4)

Using the Timer

You can set the start time of the time in the range of 1 to 60
minutes, in units of one minute. The watch beeps for 10 seconds
when the end of the countdown is reached. Turning on the auto
repeat feature causes the countdown to restart from the start time
whenever the end of the countdown is reached.
Timer Types
There are two different settings that you can use to configure the
timer as describe below.
• Repeat
With Repeat, the countdown stops, the original start time
appears, and the watch beeps for 10 seconds when the end of
the countdown is reached.
• Auto Repeat
Auto Repeat causes timing to restart from the start time when
the end of the countdown is reached.
• The countdown repeats up to 10 times, or until you stop it
manually.
Operation Guide 3334
2. Alarm Indicator
Hold down A A A for about A A
one second until the hour
digits of the alarm time
start to flash.
• This is the setting screen.
• This also causes the alarm
indicator to appear in the top
dial, and automatically turns
on the alarm.
Hour
3.
Use the D D D D D (+) and B B (–) B B B
buttons to change the
hour setting.
(Forward)
• Holding down either button
scrolls the hour setting at high
speed.
• When setting the hour, make
sure you specify AM (no
indicator) or PM (P) correctly
when using 12-hour
timekeeping, or that you
specify the correct 24-hour
time.
• The same 12-hour/24-hour
format you select for the
Timekeeping Mode time is
also applied in the Alarm
Mode.
Configuring Timer Settings
1.
In the Timer Mode, hold
down A A for about one A A A
second until the minute
digits of the timer start
time start to flash in the
bottom dial. This is the
setting screen.
Minutes
2.
Use the D D D (+) and B D D B B B (–) B
buttons to change the
start time minutes.
• Holding down either button
scrolls the start time setting at
high speed.
3.
C C button to C
Press the C C
change to the timer type
setting.
4.
C C button. C
Press the C C
• This moves the flashing to
the minute digits. As with
the hour setting, use the D
(+) and B (–) buttons to
change the minute setting.
5.
After all of the setting is the way you want, press the A
button.
• This exits the setting screen.
• The watch will also exit the setting screen automatically if you
(Back)
do not perform any operation for about two or three minutes.
(Forward)
4.
Use the D D D D and B D B B buttons to select the type of timer B B
you want to use.
• To select Repeat, display " ".
• To select Auto Repeat, display "
also displays a value in the left dial indicating the current
number of repeats.
Repeat
or
Number of Repeats
(Back)
5.
After the settings are configured the way you want,
press the A A button. A A A
• This exits the setting screen.
(Forward)
• The watch will also exit the setting screen automatically if you
do not perform any operation for about two or three minutes.
Turning an Alarm or the Hourly
(Back)
Time Signal On and Off
1.
In the Alarm Mode, use the D
(A1 to A5) or the Hourly Time Signal.
(Forward)
Minutes
2.
Press the B B button to toggle the currently displayed B B B
alarm or the Hourly Time Signal on and off.
• Turning on an alarm or the Hourly Time Signal causes its
A A
A A
indicator to appear in the top dial.
• Turning on an alarm also causes its alarm time setting to
appear in the bottom dial.
Alarm Indicator
Alarm 2 Screen
Stopping the Alarm Beeper
Pressing any button while an alarm is sounding stops it.
Testing the Alarm
In the Alarm Mode, hold down the B button to sound the alarm
tone.
Using the Timer
In the Timer Mode, press the D
• Each press of the D button starts or stops the countdown.
". Selecting Auto Repeat
• Repeat counts down in 1/10-second units, while Auto Repeat
counts down in 1-second units.
Repeat
Auto Repeat
1/10
second
(Reset)
(Start/Stop)
Minutes Seconds
• Pressing the B button while the countdown is stopped
resets the display time to the start time.
• Pressing the D button again while the timer countdown is
stopped restarts the countdown.
End of Countdown
The watch beeps for 10 seconds when the end of the countdown
is reached.
• Pressing any button while the beeper is sounding stops it.
D D button to select the alarm D D
Hourly Time Signal Indicator
Timekeeping Screen
D button. D D D
Auto Repeat
Number of
Repeats
Minutes Seconds
6