Download  Print this page

Setting Up The System - Kenwood KRF-V4060D Instruction Manual

Kenwood audio video surround receiver instruction manual vr-605, vr-615, krf-v5060d, krf-v4060d, krf-v5560d
Hide thumbs


Setting up the system

Make connections as shown in the following pages.
When connecting the related system components, be
sure to refer to the instruction manuals supplied with
the components you are connecting.
Do not connect the power cord to a wall outlet until all
connections are completed.
1. Be sure to insert all connection cords securely. If their connections are
imperfect, the sound may not be produced or there will be noise
2. Be sure to remove the power cord from the AC outlet before plugging
or unplugging any connection cords. Plugging/unplugging connection
cords without disconnecting the power cord can cause malfunctions
and may damage the unit.
3. Do not connect power cords from components whose power
consumption is larger than what is indicated on the AC outlet at the
rear of this unit.
Analog connections
Audio connections are made using RCA pin cords. These cables transfer
stereo audio signal in an "analog" form. This means the audio signal
corresponds to the actual audio of two channels. These cables usually
have 2 plugs each end, one red for the right channel and one white for
the left channel. These cables are usually packed together with the
source unit, or are available at your local electronics retailer.
Microcomputer malfunction
If operation is not possible or an erroneous display appears, even
though all connections have been made properly, reset the
microcomputer referring to "In case of difficulty".
Input mode settings
CD/DVD, VIDEO2 and DVD or DVD/6CH (VR-615/KRF-V5060D
only) inputs each include jacks for digital audio input and analog audio
To use the analog audio input for playback instead (if, for example, you
have connected a VCR to the VIDEO2 input), you must set the input
mode for the corresponding input to the analog mode.
After completing connections and turning on the receiver, follow the
steps below.
1 Use the INPUT SELECTOR knob to select CD/DVD, VIDEO2,
DVD or DVD/6CH (VR-615/KRF-V5060D only).
2 Press the INPUT MODE key.
Each press switches the setting as follows:
In DTS play mode
1 F-AUTO (digital input, analog input)
2 D-MANUAL (digital input)
In CD/DVD, VIDEO2, DVD or DVD/6CH (VR-615/KRF-V5060D
only) play mode
1 F-AUTO (digital input, analog input)
2 D-MANUAL (digital input)
3 6CH INPT (DVD/6CH input)
4 ANALOG (analog input)
Digital input:
Select this setting to play digital signals from a DVD, CD, or LD
Analog input:
Select this setting to play analog signals from a cassette deck, VCR,
or record player.
Auto detect:
In "F-AUTO" (full auto) mode (AUTO DETECT and DIGITAL
indicators light up), the receiver detects the digital or analog input
signals automatically. Priority is given to digital signal during input
mode selection. The receiver will select the input mode and listening
mode automatically during playback to match the type of input
signal (Dolby Digital, PCM, DTS ) and the speaker setting. The initial
factory setting is full auto.
To keep the receiver set to the currently selected listening mode,
use the INPUT MODE key to select "D-MANUAL" (digital manual).
However, even when this setting is selected, there may be cases
in which the listening mode is selected automatically to match a
Dolby Digital source signal depending on the combination of listening
mode and source digital.
If the INPUT MODE key is pressed quickly, sound may not be
produced. Press the INPUT MODE key again.

Hide quick links:


Table of Contents

  Also See for Kenwood KRF-V4060D

  Related Manuals for Kenwood KRF-V4060D

This manual is also suitable for:

Krf-v5060dKrf-v5560dVr-615Vr 605 - av receiverVr 605