Download  Print this page

In Case Of Difficulty - Kenwood KRF-V4060D Instruction Manual

Kenwood audio video surround receiver instruction manual vr-605, vr-615, krf-v5060d, krf-v4060d, krf-v5560d
Hide thumbs

Advertisement

In case of difficulty

Resetting the Microcomputer
The microcomputer may malfunction (unit cannot be operated,
or shows an erroneous display) if the power cord is unplugged
while the power is ON, or due to some other external factor. If
this happens, execute the following procedure to reset the
microcomputer and return the unit to its normal operating
condition.
• Please note that resetting the microcomputer will clear the contents
of the memory and return the unit to the state it was in when it left
the factory
Amplifier
Symptom
No sound from the speakers.
The standby indicator blinks and sound is
not output.
Sound is not output from one of the speak-
ers.
Sound is not output from the surround
speakers and / or the center speaker, or their
sound is very small.
A humming noise is generated when the
PHONO input selector is selected.
When playing a Dolby Digital source signal
using a DVD player, the sound is cut off soon
after it starts.
No sound is produced during playback from
a DVD player.
A video source cannot be recorded normally.
Tuner
Symptom
Radio stations cannot be received.
Interference.
A station which was preset cannot be re-
ceived by pressing the corresponding nu-
meric key.
For the U.S.A. and Canada
For other countries
Cause
• The speaker cords are disconnected.
• VOLUME is set to the minimum position.
• MUTE is ON.
• The SPEAKERS switches are set to OFF.
• Speaker cords are short-circuited.
• The speaker cord is disconnected.
• The surround speaker cords and/or the center
speaker cord is disconnected.
• A surround mode has not been engaged.
• The surround and/or center volume controls
are set to the minimum level.
• The audio cord from the record player is not
connected to the PHONO jacks.
• The record player is not grounded.
• There are many possible causes for this prob-
lem, depending on the type of DVD player
used.
• The input mode is set to digital manual.
• The software is copy-guarded.
Cause
• No antenna is connected.
• The broadcast band is not set properly.
• The frequency of the desired station is not
tuned.
• Noise due to ignition noise from an automo-
bile.
• Noise due to interference from an electric
appliance.
• Noise due to a nearby TV set.
• The preset station belongs to a frequency that
cannot be received.
• The preset memory was cleared because the
power cord had been unplugged for a long
period of time.
Unplug the power cord from the wall outlet, then
plug it back in while holding down the POWER key.
With the power cord plugged in, turn the POWER key
OFF. Then, while holding down the ON/STANDBY
key, press POWER.
• Connect them properly referring to "Connect-
ing the speakers"
• Adjust the volume to a proper level.
• Turn OFF the MUTE.
• Set the SPEAKERS switch to ON.
• Turn the power off, eliminate the short-circuit-
ing, then turn on the power again.
• Connect it properly referring to "Connecting
the speakers".
• Connect it properly referring to "Connecting
the speakers".
• Select a surround mode.
• Adjust the speaker levels using the test tone.
• Insert the audio cord plugs securely into the
PHONO jacks.
• Connect the grounding wire to the GND termi-
nal on the rear panel.
• Set the input mode to digital manual before
starting playback of the Dolby Digital source.
• Press the INPUT MODE key to select to digital
auto mode.
• Copy-guarded video software cannot be re-
corded.
• Connect an antenna.
• Set the broadcast band properly.
• Tune the frequency of the desired station.
• Install the outdoor antenna away from the
road.
• Turn off the power to the appliance.
• Install the receiver farther away from the TV.
• Preset a station with a receivable frequency.
• Preset the station again.
Remedy
#
)
(
#
#
*
8
8
Remedy
$
33
EN

Hide quick links:

Advertisement

Table of Contents
loading

  Also See for Kenwood KRF-V4060D

  Related Manuals for Kenwood KRF-V4060D

This manual is also suitable for:

Krf-v5060dKrf-v5560dVr-615Vr 605 - av receiverVr 605