Sharp LL-S242A-W Operation Manual
Sharp LL-S242A-W Operation Manual

Sharp LL-S242A-W Operation Manual

Lcd monitor
Hide thumbs Also See for LL-S242A-W:


Quick Links



Table of Contents

Summary of Contents for Sharp LL-S242A-W

  • Page 2 IMPORTANT: To aid reporting in case of loss or theft, please record the Model No.: product’s model and serial numbers in the space provided. The numbers are located in the rear of the product. Serial No.: U.S.A. ONLY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 3: Important Information

    IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within a triangle, is intended to alert the user to the CAUTION presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of RISK OF ELECTRIC sufficient magnitude to constitute a risk of electric...
  • Page 4: Dear Sharp Customer

    DEAR SHARP CUSTOMER Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product. SAFETY PRECAUTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled.
  • Page 5 SAFETY PRECAUTIONS (Continued) 19. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury, severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and missile launch control in a weapon system.
  • Page 6: Tips And Safety Instructions

    - Do not use your nails, touch pens or digitizer pens other trademarks or registered trademarks of MHL, LLC in the than the one supplied, sharp pencils, or other hard objects United States and other countries. to operate the unit.
  • Page 7: Table Of Contents

    Rack stand (front, back, support, fixing screws: 2) USB cable (USB-microUSB Type B) CD-ROM (Utility Disc) Setup Manual Logo sticker * SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission. * Keep packaging for use when transporting monitor, etc.
  • Page 8: System Requirements

    System Requirements nTouch panel To use the touch panel, the monitor must be connected to a computer using a USB cable. Touch panel operating conditions are as described below. Computer PC/AT compatible computer with a USB 1.1 port and able to output a resolution of 1920 x 1080. Windows 8.1 (32-bit or 64-bit version), Windows 8 (32-bit or 64-bit version), Windows 7 (32-bit or 64-bit version), Windows Vista (32-bit or 64-bit version) •...
  • Page 9: Part Names

    5. Cable clamp (See page 10.) 6. USB terminal (See page 12.) 7. Digitizer pen connection terminal (See page 12.) The LL-S242A-W is not supplied with a digitizer pen. Purchase a commercially available pen, as required. 8. HDMI input terminal (See page 11.) 9.
  • Page 10: Applying The Logo Sticker

    Applying the Logo Sticker You can apply the supplied logo sticker to the unit. Attach as shown in the following diagram, as required. Landscape orientation Portrait orientation Power LED Power LED Binding Cables Caution • When connecting cables, spread a soft cloth on a stable level surface such as a desk, and gently place the monitor on it with the screen facing down.
  • Page 11: Digitizer Pen Cable

    Binding Cables Digitizer pen cable You can secure the digitizer pen cable using the supplied clamper and fixing screw. 1. Pass the digitizer pen cable through the ring of the clamper. 2. Attach the clamper using the fixing screw. Clamper Fixing screw Digitizer pen cable Connecting Devices...
  • Page 12: Connecting Usb Devices

    Connecting Devices Connecting the digitizer pen TIPS • The length of the signal cables or surrounding environment (LL-P202V) may affect the image quality. • The video from the terminal that has signal input is When using the supplied digitizer pen, connect the digitizer displayed.
  • Page 13: Connecting The Monitor To A Power Source

    Connecting the Monitor to a Power Source Caution • Use only the AC adapter and power cord supplied with the monitor. 1. Connect the monitor to the power outlet using the supplied AC adapter and power cord. Back of monitor For power outlet AC adapter...
  • Page 14: Installation

    3. Place the monitor in the standing position, and adjust following positions. the angle of the stand. Hold the display with one hand so that it does not fall over, Installation position LL-S242A-W LL-P202V hold the rear leg of the stand with your other hand, and Standing Rack stand adjust the angle of the stand.
  • Page 15 Installation 3. Peel off the adhesive tape securing the support to the nLL-S242A-W back side. Placement on the rack stand Place the unit on the supplied rack stand. 1. Attach the back of the stand to the front. Tape Place the front and back sides together, and attach the hinge.
  • Page 16 Installation Portrait orientation Disassembling the rack stand Remove the monitor from the rack stand before disassembling the stand. Caution • After removing the monitor from the rack stand, store the stand so that the screws will not be lost. 1. Remove the screws and remove the monitor. Remove fixing screws Run the cables along the hollow on the front side and out between the legs of the back side.
  • Page 17: Installing On A Table (Pen Writing Position/Horizontal Position)

    Installing on a table Horizontal position Place the monitor on a table or other level surface. (Pen writing position/Horizontal position) Caution • When using the monitor horizontally, use the horizontal tab Remove the monitor from the stand and place face-down on a in the upright position.
  • Page 18: Turning Power On/Off

    Turning Power On/Off Turning on the power Turning off the power 1. Press the POWER button. 1. Turn off the PC. 2. Depress the POWER button for around 2 seconds. POWER button POWER button Press Depress for around 2 seconds The power LED turns off.
  • Page 19: Installing The Software

    Installing the Software To use the touch panel or the supplied digitizer pen, the required software must be installed for the operating system of the connected computer. The required software is given below. LL-S242A-W LL-P202V Windows Windows Windows Windows Windows Windows 8.1 / 8...
  • Page 20: Touch Actions

    Touch Actions Touch action modes TIPS • In Windows 7, if the checkmark has been removed from There are three touch action modes: finger/pen mode, pen- “Enable multi-touch gestures and inking” in “Pen and touch” only mode, and finger-only mode. These modes can be in Control Panel, select the checkbox.
  • Page 21 Touch Action nFinger actions Drag-and-drop Touch the screen with your finger/pen and move without lifting. Zoom When you have finished the movement, lift your finger/pen. While touching the screen with two fingers, move them closer together and farther apart. Slide to pan With your finger/pen touching the screen, move it up and Pinch down to scroll the screen.
  • Page 22: Digitizer Pen

    Touch Action Digitizer pen TIPS • The shortcut launcher is not displayed on the Windows 8.1/8 The LL-P202V monitor supports a digitizer pen. To use the Start screen or on the Windows Store screen. digitizer pen, the utility software must be installed. (See page •...
  • Page 23: Other Functions

    Touch Action nSpare pen tip storage 1. Unscrew the pen tip cover and remove it. The pen stand features a pen tip storage area where you can store spare pen tips. TIPS • Spare pen tips are not stored in the stand at the time of purchase.
  • Page 24: Monitor Settings

    Monitor Settings Menu operations 4. Touch [Exit] or press the MENU button. The menu screen disappears. The monitor settings are configured by displaying the menu screen. The operations on this page are the basic operations. Caution • Do not turn off the power while the menu screen is displayed.
  • Page 25: Menu Functions

    Monitor Settings Menu functions Exit Setup Input Select Volume Finger-only Pen-only Finger/pen mode mode mode Touch mode selection Touch mode selection These icons switch the touch action mode. Input Select ) mark is displayed at the top of the icon for the selected mode.
  • Page 26: Setup Menu Details

    Monitor Settings SETUP Menu Details nMode on Start Up Touch Mode This setting configures the touch action mode (See page 25) used when the monitor is turned on. Menu Position Reset: The monitor starts in finger/pen mode. Save: The monitor starts in the mode that was last used. Position Menu Position When the monitor is used in portrait orientation (power/menu...
  • Page 27: Prohibiting Operations (Operation Lock)

    Monitor Settings Prohibiting operations (operation lock) Operation lock is enabled. A key mark is displayed on the screen and it disappears after around 5 seconds. This function makes it possible to prohibit operations to turn The key mark can be set to always be displayed. (See the power off and to prohibit touch action on the screen.
  • Page 28: Monitor Status Indicators

    Monitor Settings n Disabling operation lock Monitor status indicators 1. Press the MENU button. The status is displayed on the right-side of the screen. The menu screen is displayed. Touch Mark MENU button Key Mark Touch Mark The touch mark displays the current touch action mode. Finger/pen mode Press This mark is displayed during fi nger/pen mode.
  • Page 29: Troubleshooting

    Troubleshooting If you are experiencing any problem with your display, before The response of the touch screen is slow. calling for service, please review the following troubleshooting Some parts of the screen do not respond. • When starting your computer or connecting the USB cable, tips.
  • Page 30: Specifications

    * When the DisplayPort input terminal and touch panel are connected. As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production...
  • Page 31 Specifications nDimensional Drawings Note that the values shown are approximate values. LL-S242A-W VESA holes * 1-1/8 [28.7] 1-15/16 1-15/16 (excluding protrusions) 22-5/16 [566.4] [50] [50] Unit: inch [mm] Screen display size (20-1/2 [521.3]) LL-P202V VESA holes * 1-15/16 1-15/16 [50] [50] 1 [25.2]...
  • Page 32 Specifications LL-P202V 20° 12-11/16 [323] 5-1/2 [137.6] (20 degrees) (75 degrees) * Height of bottom of screen from table surface nPen writing position (LL-P202V) 10-13/16 [275.3] nSupported frequency Resolution Frame rate Remarks 640×480 60Hz 800×600 60Hz SVGA 1024×768 60Hz 720×480p 59.94/60Hz 1280×720p 50/59.94/60Hz...
  • Page 33 Specifications HDMI input terminal pins nDisplayPort input terminal pins (HDMI Connector) (DisplayPort 20 pin) Function Function Function Function TMDS data 2+ TMDS clock shield MainLane 3- TMDS data 2 shield 12 TMDS clock- 12 MainLane 0+ TMDS data 2- 13 CEC MainLane 3+ 13 Gnd TMDS data 1+...
  • Page 34 LL-S242AP202V Mu EN14A(1)

This manual is also suitable for:


Table of Contents