BIS TRADITION CE 506128-19 Installation And Operation Instructions Manual

BIS TRADITION CE 506128-19 Installation And Operation Instructions Manual

Epa wood-burning fireplace

Advertisement

SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
Fireplace, also for use in mobile or
manufactured homes with solid fuel only.
An French manual is available upon request. Order P/N 506128-20.
Ce manuel est disponible en francais, simplement en faire la demande. Numéro
de la pièce 506128-20.
• Hot! Do not touch! The glass and
surfaces of this appliance will be hot
during operation and will retain heat
for a while after shutting off the appli-
ance. Severe burns may result.
• Carefully supervise children in the
same room as appliance.
• If small children are present in the home, it is
recommended that this appliance be fitted with
an adjustable safety gate or barrier screen.
WARNING
Listed to standards:
ULC-S610 and UL-127
Report No. 307-4084
EPA Cert. No. 537
PIBISTRADCE REV. 9 05/2013
INSTALLATION AND

OPERATION INSTRUCTIONS

BIS
TRADITION CE
®
EPA Wood-Burning Fireplace
P/N 506128-19 REV. J 05/2013
MODEL
BISTRADCE
This installation manual will enable you to obtain a safe, efficient
and dependable installation of your fireplace system. Please read
and understand these instructions before beginning your installation.
Do not alter or modify the fireplace or its components under any cir-
cumstances. Any modification or alteration of the fireplace system,
including but not limited to the fireplace, chimney components and
accessories, may void the warranty, listings and approvals of this system
and could result in an unsafe and potentially dangerous installation.
IHP wood-burning fireplaces are designed for use as a supplemental
heater. They are not intended for continuous use as a primary heat
source.
• The fireplace cannot be operated without a door
or firescreen. Consult your dealer to select the
correct replacement door or firescreen.
• The fireplace is equipped with a blower, electri-
cal connection must be made prior to fireplace
installation
• Important! To assure proper alignment of glass
doors: Install this fireplace in a square and
plumb condition, using shims as necessary at
sides and/or bottom.
• Install the fireplace only as described in these
instructions.
WARNING

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TRADITION CE 506128-19 and is the answer not in the manual?

Questions and answers

Summary of Contents for BIS TRADITION CE 506128-19

  • Page 1: Operation Instructions

    INSTALLATION AND OPERATION INSTRUCTIONS TRADITION CE ® EPA Wood-Burning Fireplace P/N 506128-19 REV. J 05/2013 MODEL BISTRADCE This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system. Please read and understand these instructions before beginning your installation. Do not alter or modify the fireplace or its components under any cir- cumstances.
  • Page 2: Safety Rules And Specifications For Mobile Or Manufactured Home Installation

    Avoid using WARNING combustible flowing window can block the entrance of air. treatments such as curtains on The BIS Tradition CE fireplace ® nearby windows that are of suf- IMPORTANT must be installed with an outside...
  • Page 3: Table Of Contents

    Dealing With A Chimney Fire .....Page 5 • The BIS Tradition CE fireplace is NOT intended has been exposed to salt or other chemicals. Finish Door Casing Care ....Page 5 for use with a gas log set. Do not use a Salt or chemicals can corrode the firebox and Disposing of Ashes ......Page 6...
  • Page 4: Starting And Maintaining A Fire

    6-8 hours. reload with wood every one or two hours. This wood can be added (see Primary Air Combus- is the least efficient method of burning the BIS tion Control section for proper operation of the REFUELING FOR BEST PERFORMANCE Tradition CE fireplace.
  • Page 5: Important Cautions

    When H. Do not burn wood in the area in front of the can prevent chimney fires. If you have a chimney operating the BIS Tradition CE fireplace, grate. fire, follow these steps: ®...
  • Page 6: Disposing Of Ashes

    2. Remove the bottom refractory WARNING 3. Remove the left side refractory 4. Remove the right side refractory • Use only a IHP glass doors, specifically designed for the BIS Tradition 5. Remove the back refractory CE fireplace. 6. Remove the front ceramic baffle •...
  • Page 7: Facade Installation

    Cover the insulation with drywall panels around the fireplace. 12" MAX. (305mm) Hearth Extension Requirements Area where wood The BIS Tradition CE fireplace may be installed ® Mantel can be Mantel directly on a combustible floor. The supplied...
  • Page 8: Framing Dimensions

    Back Wall of Chase/Enclosure OUTSIDE CHASE FRAMING DIMENSIONS Including Finising Materials if any Corner Installation Fireplace Opening Width 19-19/32” 36-1/4” 921 mm 42” 1067 mm * Zero Clearance From Back 30-1/16” 764 mm Spacer to Wall 13-1/2” 343 mm 77” 1956 mm 37-1/2”...
  • Page 9: Nailing Flanges

    Insulate Joists Same As Ceiling INSULATED CHASE CONSTRUCTION Storm Collar Roof Support Flashing Draft Stops Attic Radiation Shield Floor Ceiling Firestop NOTE: It is recommended that the Wall chase walls and floor be insulated CTDT in the same manner, using the Termination same insulation, as the rest of the building, below the attic.
  • Page 10: Fireplace Blower

    Maximum length See Figure 14 Figure 15 Noncombustible Facing * The height of the louver must be measured from the base of the BIS Tradition CE fireplace When installing the double outlet system, the Drywall to the middle point of the louver.
  • Page 11: Outside Air Kit

    OUTSIDE AIR KIT It is mandatory to install an outside air con- Rain Cap nection to the BIS Tradition CE wood burn- ® ing fireplace. The following components are required and are included with the fireplace: Flashing Collar Flashing • Outside air kit (includes 4 inch flex that goes...
  • Page 12: Chimney System

    NOTE: Blown or fill type insulation materials must not be in contact with are especially prone to flow reversal. the fireplace or in the enclosure frame as described in ‘’Enclosure’’ section. 2. The IHP fireplace model BIS Tradition CE may be installed only with ®...
  • Page 13: Chimney Installation Instructions

    CHIMNEY INSTALLATION Attic Radiation Shield INSTRUCTIONS Attic Radiation ASHT / S2100 Shield HT6103+ / HT6000+ 1. Cut and frame the holes in the ceiling, floor Solid Packed Pipe * Flashing and roof where the chimney will pass (see Figure 21). Use a plumb-bob to line up the center of the holes.
  • Page 14: Offset Chimney Installation

    After reaching the location requiring the elbow, proceed as follows: Air Cooled Chimney Chimney ASHT+ / HT6103+ / S-2100+ / HT6000+ Collar Chimneys Spacer (built 1. Install the first elbow; turn it in the required into flashing) direction. Fasten it to the chimney with the three (3) 1/2”...
  • Page 15 Offset Dimensions Total Height Horizontal Offset Chimney Elbow Offset & One Length Between Elbows Two Lengths Between Elbows 6” Height 8” 12” 18” 24” 36” 48” 8” & 48” 12” & 48” 18” & 48” 24” & 48” 36” & 48” 48”...
  • Page 16: Angled Wall Radiation Shield

    ANGLED WALL RADIATION SHIELD OFFSET CHIMNEY INSTALLATION (RSM+ and RSMI30) Chimney AC When traversing a combustible wall with the chimney at a 30º or 45º angle, an angled firestop or wall radiation shield must be installed. Only one is required. RSMI45 NOTE: 45º...
  • Page 17: Glass Care - Replacement

    DO NOT OPERATE THE UNIT WITH CRACKED if additional support is needed. OR BROKEN GLASS. The BIS Tradition CE fireplace may be installed Glass Cleaning Gasket Length Dimensions Part No.
  • Page 18: Chimney Support Installation

    CHIMNEY SUPPORT INSTALLATION Universal Roof Support 18” (460 mm) When installing a support, slightly lift the chimney system so the weight 18” (460 mm) will lie on the support, not on the fireplace to reduce expansion noises. This support has three possible uses: 1.
  • Page 19: Masonry Application Instructions

    INSTALLATION INSTRUCTIONS FOR MASONRY APPLICATION Follow these steps: 1- Position the fireplace in its location. Temporarily install the ASHT+ WARNING: Before starting the installation, the masonry chimney elbow on the top of the fireplace and, using a level, mark with an oval must be inspected by a qualified chimney sweep.
  • Page 20: Installation Accessories

    Tradition CE Facade Black, BTCEFBK BTCEFBK ® Central Forced Air Kit, Central forced air kit including: blower BIS Tradition CE Facade Gold Plated, BTCEFG BTCEFG (BISZY), flex adaptor (BISAF), 2 clamps, variable speed control (VRUW), thermo-disk (VTU), fan to flexible pipe...
  • Page 21: Replacement Parts

    SPECIFICATIONS Tradition CE Replacement Parts Cat. No. Model ® Description Part/Cat. No. BISTRADCE BIS TRADITION CE Blower (heat activated on/off pre-wired), UZY5 UZY5 Blower motor speed control (wall mount), VRUW VRUW Product Reference Information Weight 300 lbs Snap Disc, Blower Height 36”...
  • Page 22: Chimney Components Lists

    450-973-9999 2125 Monterey, Laval, Quebec 1-800-361-4909 (USA) Canada, H7L 3T6 1-800-667-3387 (Canada) www.securitychimneys.com Fireplace Model BIS Tradition CE - Approved Venting Components ® Secure Temp ASHT 1” High Temp. Insulated Stainless Steel Chimney ® manufactured by Security Chimneys International™ only.
  • Page 23 SECURITY CHIMNEYS™ - PARTS AND COMPONENTS LISTS The components listed below must be ordered from Security Chimneys International™. Contact your Security Chimneys Distributor or Dealer for ordering information. Security Chimneys International Limited 450-973-9999 Tubinox™ LL Chimney Lining System 2125 Monterey, Laval, Quebec 1-800-361-4909 (USA) Rigid Stainless Steel Liner For Relining A Masonry Chimney, 6”...
  • Page 24: Product Reference Information

    WARRANTY Normally, all parts should be ordered through your IHP distributor or dealer. Parts will be shipped at prevailing prices at time of order. Your fireplace is covered by a limited warranty. Please read the warranty When ordering repair parts, always give the following information: to be familiar with its coverage.

This manual is also suitable for:

Tradition ceBistradce

Table of Contents