Operating A Cable Box - Sony KP-43T70K Service Manual

MDP manufacturer code numbers
Manufacturer
Sony
Panasonic
Mistubishi
DVD Player manufacturer code
numbers
Manufacturer
Sony
Panasonic
Pioneer
RCA
Toshiba
Tips z
• In some rare cases, you may not be able to operate
your non-Sony video equipment with the supplied
remote control. In this case, please use the
equipment's own remote control.
• When you remove the batteries, the code number may
revert to the factory setting.
To operate video equipment
1
Press DVD/VTR (FUNCTION).
2
Use the VCR/DVD/MDP operation
buttons indicated in the following tables.

Operating a Cable Box

Setting the Manufacturer's
Code
You can program the supplied remote control
to operate a cable box.
Press CODE SET, SAT/CABLE
(FUNCTION)*, and the 0-9 buttons to enter
the manufacturer's code number (see the
following chart), then press ENTER.
For example, to operate a Pioneer cable box:
FUNCTION
CODE SET SAT/CABLE
2 1
Manufacturer code numbers
(cable box)
Manufacturer
222, 223, 224, 225, 226
Hamlin/Regal
201, 202, 203, 204, 205,
Jerrold/G.I
222, 206, 207, 208, 218
Oak
Panasonic
Pioneer
Scientific Atlanta
Tocom
Zenith
3 2
Operating a VCR using the remote control
Code
To turn On/Off
701
To select a channel
704, 710
702
To change channels
To record
To play
To stop
To fast forward
Code
To rewind the tape
751
To pause
753
752
755 To search the
754 picture forward or
backward
To change input
mode
Operating an MDP using the remote
control
To turn On/Off
To play
To stop
To pause
To operate the cable box
1
Press SAT/CABLE (POWER)* [Green
Button] to turn on/off the cable box.
2
Press SAT/CABLE (FUNCTION)*.
3
For other operations, refer to the
operating instructions that come with the
equipment.
* The SAT/CABLE (POWER) and SAT/CABLE
(FUNCTION) buttons cannot operate a satellite
ENTER
receiver (SAT) in Taiwan (the Republic of
4
China) even if it is connected to the projection
TV.
If the remote control doesn't work
• Try repeating the set up procedures using
Code
the other codes listed for your equipment.
To operate the projection TV
227, 228, 229
219, 220, 221
Press TV (FUNCTION). Then use the
214, 215
projection TV control buttons to control the
209, 210, 211
projection TV.
216, 217
212, 213
– 22 –
To search the picture
forward or backward
Press DVD/VTR (POWER).
[Green Button]
To search a chapter
Press the 0 – 9 buttons.
forward or backward
Press CH +/–.
Press ( while pressing r.
Operating a DVD Player using the remote
Press (.
control
Press p.
To turn On/Off
Press ).
Press 0.
To play
Press P. Press again to
To stop
resume normal playback.
To pause
Press ) or 0 during
playback. Release to
To step through
resume normal playback.
different tracks of
Press TV/VTR.
an audio disc
To step through
different chapters
of a video disc
To select tracks
directly
To display the
Press DVD/VTR (POWER).
menu (Set up)
[Green Button]
Press (.
Press p.
Press P. Press again to
resume normal playback.
Tips z
• If more than one code number is listed, try entering
them one by one until you come to the correct code
for your equipment.
• If you enter a new code number, the code number
you previously entered at that setting is erased.
• In some rare cases, you may not be able to operate
your equipment with the supplied remote control. In
this case, use the equipment's own remote control
unit.
• Whenever you remove the batteries — to replace
them, for example — if too much time is taken, the
code numbers may revert to the factory setting and
must be reset.
Press ) or 0 during
playback. Release to resume
normal playback.
Press CH +/–.
Press DVD/VTR (POWER).
[Green Button]
Press (.
Press p.
Press P. Press again to
resume normal playback.
Press ) to step forward or
0 to step backward.
Press CH + to step forward
or CH – to step backward.
Press 0-9 buttons.
Press MENU.
3 1