Kenwood DPF-1010 Instruction Manual

Kenwood instruction manual cd player dpf-1010 dpf-2010 dpf-3010
Hide thumbs


B60-3730-08 00 KO ( T, M, X ) OC
99/12 11 10 9 8 7 6 5 4 3 2 1 98/12 11 10 9 8 7 6 5 4 3



  Also See for Kenwood DPF-1010

  Related Manuals for Kenwood DPF-1010

  Summary of Contents for Kenwood DPF-1010

  • Page 1: Audio Cord

    CD PLAYER DPF-1010 DPF-2010 DPF-3010 INSTRUCTION MANUAL KENWOOD CORPORATION COMPACT DIGITAL AUDIO B60-3730-08 00 KO ( T, M, X ) OC 99/12 11 10 9 8 7 6 5 4 3 2 1 98/12 11 10 9 8 7 6 5 4 3...
  • Page 2: Introduction

    Introduction Before applying power Units are designed for operation as follows. Australia ... AC 240 V only Europe and U.K..AC 230 V only *AC voltage selection The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped.
  • Page 3: Table Of Contents

    ¶ Edit function for rearranging tracks according to the tape length so that no music is interrupted in the middle. ¶ Auto space function. ¶ Easy operation functions allow systematic operation with other KENWOOD components connected through the system control connection. System control cord ... (1) Batteries (R6/AA) ...
  • Page 4: Important Safeguards

    IMPORTANT SAFEGUARDS Please read all of the safety and operating instructions before operating this appliance. Adhere to all warnings on the appliance and in the instruction manual. Follow all the safety and operating instructions. operating instructions should be retained for future reference.
  • Page 5 Caution : Read this page carefully to ensure safe operation. 13.Lightning – For added protection for this appliance during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system.
  • Page 6: System Control Cord

    System connections Caution: Do not plug in the power lead until all connections are com- pleted. Make connections as shown below. When connecting the related system components, refer also to the instruction manuals of the related components. Caution regarding placement To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal to, or greater than, shown below.
  • Page 7: To Use The Headphone

    RC-P0305 To use the headphone (only for DPF-3010) Connect a stereo headphone to the PHONES jack of the CD player. Adjust the sound volume using the remote control unit. ÷ It is not favorable for the sound quality to decrease the output level from this unit too much.
  • Page 8 3. Do not connect system control cords to any components other than those specified by Kenwood. It may cause a malfunction and damage your equipment. 4. Be sure the system control plugs are inserted all the way in to the system control terminals.
  • Page 9: Maintenance

    When a disc is not to be played for a long period of time, remove it from the CD player and store it in its case. Never play a cracked or warped disc. During playback, the disc rotates at high speed in the player.
  • Page 10: Controls And Indicators

    Controls and indicators TRACK TRACK mode indicator Program mode indicator Pause indicator Play indicator The figure shows an example for the DPF-3010 2 3 4 ON/STANDBY P.MODE PHONES EDIT 0 ! @ The keys with the same name as those on the remote control unit operate the same way as the remote control unit.
  • Page 11: Operation Of Remote Control Unit

    Operation of remote control unit DISC SELECTOR DISC SELECTOR RANDOM REPEAT DISC SKIP DISC SKIP P.MODE TIME DISPLAY EDIT CHECK CLEAR ¢ OUTPUT ¡ DOWN REMOTE CONTROL UNIT RC-P0305 Loading batteries 1 Remove the cover. Operation After plugging in the power cord, press the ON/STANDBY ) switch of the main unit to turn the unit ON.
  • Page 12: Normal Play (Track Mode)

    Normal play (TRACK mode) Use the following procedure to play a CD in the original order of tracks from track No. 1. Playing tracks in order from track No. 1 Press the ON/STANDBY switch to ON. Load a disc. Open the tray. Place a disc.
  • Page 13: Playback From Desired Track

    To skip backward Searching Backward search Time display on CD player (TIME DISPLAY) Each press of the TIME DISPLAY key changes the displayed contents. TIME DISPLAY Press the numeric keys as shown below... To enter track No. 23 : To enter track No. 40 : ÷...
  • Page 14: Programmed Play (Pgm Mode)

    Use the following procedure to program desired tracks in a desired order. (up to 20 tracks) Preparation ÷ Load a disc in the CD player. Press so that the “PGM” indicator lights. Do this operation in the stop mode. Program desired tracks.
  • Page 15: To Check Or Change The Programmed Tracks

    To check or change the programmed tracks Press the CHECK key. CHECK Select the new track No. Set the entry. P.MODE To add a track to the program Select the desired track No. Press the P .MODE key. To clear tracks from the program Press to clear tracks from the end.
  • Page 16: Repeated Playback

    Repeated playback Preparation ÷ Load a disc in the CD player. ™ To repeat only the programmed tracks Press so that the "PGM" indicator lights. Do this operation in the stop mode. Select the desired track No. Press the numeric keys as shown below...
  • Page 17: To Repeat The Entire Disc

    To repeat the entire disc Press so that the “TRACK” indicator lights. P.MODE Switch REPEAT ON. REPEAT Start playback. PLAY/PAUSE To cancel repeated playback Press the REPEAT key again. REPEAT : Keys and control used in the operations described on this page. Lights up.
  • Page 18: Editing

    6 key again to continue playback. When recording the edited content onto a tape, it is recommended to use the synchro recording or CCRS recording function of KENWOOD cassette decks. ÷ Do not adjust the output level from this unit particularly during record- ing.
  • Page 19: To Check The Edited Contents

    To check the edited contents CHECK To clear the edited contents Press any one of these keys. P.MODE Peak search This function identifies the highest peak level of the entire recording on a CD before recording the CD on the cassette deck. With this unit, after the peak level of each track recorded on the CD has been searched, the section of the music containing the highest peak level will be played repeatedly so that the recording level of the cassette deck or MD (analog recording) can be adjusted easily.
  • Page 20: Playback In Random Order (Random Playback)

    Playback in a random order (Random playback) As tracks are selected at random, you can enjoy listening to for a long time. Preparation ÷ Load a disc in the CD player. ™ Press the P.MODE key so that the "TRACK" indicator lights.
  • Page 21: Timer Operations

    Turn OFF the power output from the audio timer. 1. Some amplifiers cannot be used with a timer. Before using a amplifier, check it. 2. When operating the unit other than CD player using an audio timer, be sure to remove the disc from the CD player. Notes...
  • Page 22: In Case Of Difficulty

    Set the unit to STANDBY mode by pressing the ON/ STANDBY ( unit ON by pressing the ON/STANDBY ( ÷ Please be aware that resetting the CD player will erase all stored information and return it to the factory settings. Cause ÷...
  • Page 23: Specifications

    Weight (Net) ... 4.3 kg (9.5 lb) 1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice. 2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
  • Page 24 For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your dealer for information or service on this product.

This manual is also suitable for: