Replacing The Filter; Removing The Filter; Technical Specification - DeLonghi ECAM26455M Instructions For Use Manual

Please note
The filter lasts about two months if the appliance is used
normally. If the coffee maker is left unused with the filter
installed, it will last a maximum of three weeks.
3. Remove the tank from the appliance and fill with water.
4. Insert the filter in the water tank and immerse it
completely for ten or so seconds, sloping it to enable the
air bubbles to escape (fig. 34).
5. Insert the filter in the filter housing (fig. 35A) and press as
far as it will go.
6. Close the tank with the lid (fig. 35B), then replace the tank
in the machine.
When you install the filter, you must notify the appliance of its
presence.
7. Press the menu/esc button to enter the menu;
8. Press the milK or
cappuccino button
(fig. 8) until "Install
filter" is displayed;
9. Press the
button;
10. The message "Enable?" is
displayed.
11. Press the
button to confirm the
selection. "Hot water
Confirm?" is displayed.
12. Position a container with
a minimum capacity of
3.4 oz / 100 ml under the
hot water spout.
13. Press the
button to confirm the
selection. The appliance
begins delivering hot
water and the message
"Please wait "
displayed.
14. After delivery, the
appliance returns
automatically to the
"Ready for coffee"
position.
The new filter is active. You can
now use the coffee maker.

replacing the filter

When "REPLACE FILTER" is
displayed, after two months
(see date indicator) or when
is
the appliance has not been used for 3 weeks, you should
replace the filter:
1. Remove the exhausted filter;
2. Remove the new filter from the packaging.
3. Turn the date indicator disk (see fig. 33) until the next 2
months of use are displayed (the filter lasts about two
months);
4. Refill the tank;
5. Insert the filter in the water tank and immerse it
completely, tilting it to enable the air bubbles to escape
(fig. 34);
6. Place the filter in the filter housing (fig. 35aa) and press as
far as it will go. close the tank with the lid (fig. 35b), then
replace the tank in the machine;
7. Position a container with a minimum capacity of 3.4 oz /
100 ml under the hot water spout.
8. Press the menu/esc button to enter the menu;
33
9. Press the milK or cappuccino button until "Reset filter
" is displayed.
10. Press the
11. The message "Confirm?" is displayed.
12. Press the
13. "Hot water, Press OK" is displayed.
14. Press the
appliance begins delivering hot water and the message
"Please wait " is displayed.
15. After delivery, the appliance returns automatically to the
"ready for coffee" position.
The new filter is now active and you can use the coffee maker.
34

removing the filter

If you want to continue using the appliance without a filter,
you must remove it and notify the appliance of its removal as
follows:
1. Extract the tank and exhausted filter;
2. Press the menu/esc button to enter the menu;
3. Press the milK or cappuccino button (fig. 8) until
"Install filter Enabled" is displayed;
4. Press the
35A
5. "Disable?" is displayed;
6. Press the
button to exit the menu.

technical specification

Voltage:
Absorbed power:
35B
Pressure:
Water tank capacity:
Size Lxhxd:
Cable length:
Weight:
Beans container capacity:
19
button;
button to confirm the selection;
button to confirm the selection. the
button
button to confirm and the MENU/ESC
120V~60 Hz
67.62 fl. oz. / 2.0 liters max.
9.3x13.8x17.5 in / 238x350x445 mm
2,92 ft / 1.80 m
260 lb / 11.8 kg
8.82 oz / 250 g max.
1250W
15 bar