NAD T 787 Owner's Manual page 7

6 VACUUM FLUORESCENT DISPLAY (VFD)
• Displays visual information about the current settings like the active
Source, volume level, listening mode, audio format, applicable
RDS/XM/DAB as well as iPod-related display information and other
related indicators.
• Refer also to the item about DISPLAY SETUP under the USING THE
T 787 - SETUP MENU segment of the OPERATION section.
7 REMOTE SENSOR
• Point the HTR 8 remote control at the remote sensor and press the
buttons.
• Do not expose the remote sensor of the T 787 to a strong light
source such as direct sunlight or illumination. If you do so, you may
not be able to operate the T 787 with the remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30
o in each direction of the front of the remote sensor.
8 a SOURCE s
• Toggle through the input selections - Source 1, Source 2, Source 3,
Source 4, iPod, Source 7, Front Input, Media Player and Tuner (AM/
FM/DAB/XM as applicable). More Sources can be directly recalled
upon enabling them at the Setup Menu.
• Refer also to the item about SOURCE SETUP under the USING THE
T 787 - SETUP MENU segment of the OPERATION section.
9 VOLUME
• The VOLUME control adjusts the overall loudness of the signal being
fed to the loudspeakers or headphones.
• Turn clockwise to increase the volume level; counter clockwise to
lower it.
10 PHONES
• Accepts stereo headphone using a standard 1/4-inch stereo phone
plug (use a suitable adaptor for headphones equipped with a
smaller plug).
• For headphone listening, the Front speakers must be set to "Large" at
the "Speaker Configuration" of the Speaker Setup item at the Setup
Menu; otherwise headphone bass response will be restricted.
11 A SPEAKERS B
• Press either Speaker A or B or both to select the set of speakers you
wish to listen.
• Speaker A is the main set of 7 multichannel and surround speakers.
• Speaker B is an auxiliary set for remote locations such as other
rooms of your home. For Speaker B selection, all surround sound
sources are downmixed to stereo. Combining Speaker A and
Speaker B (SPEAKERS A + B) will also result to the source being
downmixed to stereo.
12 AM/FM/DB
• Toggle this button to select AM, FM, DAB (230V version only) or XM
(120V version only) tuner functions.
13 TUNER MODE
• In FM mode, this button will toggle between FM STEREO and FM
MONO.
• Select FM MONO (FM STEREO and FM MUTE icons at VFD are
extinguished) for stations that have too much interference or are
too weak.
• In DAB (230V version only) or XM (120V version only) radio, this
button enables the digital radio menu in conjunction with the
Navigation and Enter buttons.
IDENTIFICATION OF CONTROLS
14 LISTEN MODE
• Toggle to select through the various Listening mode options.
Depending on the format of the currently selected input (digital
or analog, stereo or multichannel), various listening modes are
available.
• Refer also to the item about LISTENING MODE under the USING THE
T 787 – MAIN MENU segment of the OPERATION section.
15 TONE
• Press to adjust TREBLE control using the VOLUME knob over a
± 10dB range. Press again to adjust BASS control and a third time for
DIALOG control.
• Refer also to the item about TONE CONTROLS under the USING THE
T 787 – MAIN MENU segment of the OPERATION section.
16 TONE DEFEAT
• Tone Controls are enabled or disabled by pressing this button. Tone
controls are bypassed at "Tone Defeat" while at "Tone Active", the
tone controls are enabled again.
• Refer also to the item about TONE CONTROLS under the USING THE
T 787 – MAIN MENU segment of the OPERATION section.
17 FRONT INPUT/MP
• Toggle button to switch between Front Input and Media Player
input.
18 FRONT INPUT PORTS
• Use these convenience jacks for occasional sources such as a
camcorder, video game console, any analog audio or HDMI sources
and composite or S-Video sources.
• If your source has a single audio out jack only or is marked "Mono
output", plug this into the T 787's Front "R (MONO)" input (item B).
• On the other hand, if your source has two output jacks indicative of
stereo output, insert both jacks into the T 787's corresponding Front
"L" (item A) and "R (MONO)" input to achieve stereo output as well.
• Connect composite video output source to the front composite
video input (item C).
• Connect S-Video output source to the front S-Video input (item D).
• Use the front HDMI input (item E) to connect directly an HDMI
output source.
19 FRONT MP/MIC INPUT
• Connect your Media Player's standard stereo phone jack to this
input.
• This is also same input where the supplied Audyssey microphone is
connected for Audyssey Auto calibration.
• Refer also to the item about AUDYSSEY AUTO CALIBRATION under
the USING THE T 787 - SETUP MENU segment of the OPERATION
section.
FRONT PANEL
7