Viper Responder one Owner's Manual page 20

PllllJIOmming System Features
The System Features learn Routine dictates how the unit operates It is
possible
to access and change most of the
featu re settings using the Va let button.
1 Turn the ig ni tion on, then off.
2. Select o Menu . W ithin 10 seconds, Press and hold the Va let button. The number of LED flashes and horn
honks indicates the menu number. A single L ED flash and honk indicates menu 1 Two L ED flashes and 2
honks ind icates menu 2.
When the desired menu LED flashes and honks are heard, release the Valet bulion
4
Select a
Feature, within 1 0 seconds. Press and release the Valet button the number
of
times correspond-
ing to the feature you wish to change . Then press and hold one more ti me to select the feature. The LE D
flashes and the horn honks to indicate which feature is selected.
5.
Program the Featu re. While holding the Valet button, you can progra m the fea ture using the remote
control
Pressing the button on the remote control advances to each fea ture option . The LED fla shes and the horn honks
indicating which option is selected.
Once o feature is programmed:
Other features con be prog ra mmed within the some menu
Another menu con be selected
The lea rn routine con be exited if programm ing is complete
To access another feature in the same menu :
1 Press and release the Va let button the number of times neceswry to advance from the feature you just pro-
grammed to the next o ne you wont to program.
2.
Then press the Va let button once more and hold it
To select another menu:
1 Press and hold the Valet button
2.
After
3
seconds, the unit advances to the next menu, the horn honks and LED flashes indicating which menu
has been accessed.
The learn routine exits
if
any
of
the
f~lowing
occurs:
The ignition is turned On
There is no activity for
30
seconds
The Valet button is p ressed too many times
Bilwriter -Only Options
II
If program ming w ith the _Bilwriter®, the learn routi ne can be locked or unlocked . If the learn routi ne has
previously been locked, 1 1 must
be
unlocked w ith Bitwriter® - this cannot be done man ually w ith the Va let
button.
The Bitwriter®
II
gives you access too w ider ra nge of system options. These additional features and the ad just-
ments that may be programmed are described in the table below.
©
201 1 Directed Electron ics. All rights Reserved
Feature Menus
Default settings are in
bold
type.
Menu 1
Feaiure I Feature Opt. 1
Ho rn function
Off
Ignition con- On
trolled un lock
Doorlock out-
put duration
~~~le
pu lse
0:8 sec,
Off
Opt. 2
Si ren
20 mS
Off
3.5
sec.
On
Opt. 3 Opt.4 Opt. 5+
Siren Siren Siren
30 mS 40 mS 50 mS
- - - - - - - - - - -.
OAsec .
Off On
f-----Double pu lse ---,-:;-----,-------;-----,--
lock
Factory Alarm
Disarm func-
tion
'-·~·
Factory Ala rm
~i-7~-,....-',-Disorm
Pulses
Comfort *
C losure
with unlock
f·
Panic*
qn
Before unlock
t
~'-'''-'·':..,<:
.....
~~.-
·Option not available on 1-button remote
Menu2
1' 2 -min ..
•Option not available on 1-button remote
latch rear
defogger
Off
Timed
15
sec
3
min
Pulse f~r · · · :
defogger
Time'd
30
sec.
Timed
45
sec
6
min
9
min
Remote Programming
1 . Turn key to the ON position
2 With in 10 seconds, press and release Valet button one time
3.
Within
10
seconds, press and hold the Valet button. The LED w ill flas h one time and the horn hon ks (if con-
nected) to confirm entry into remote programming
4. Press the button on the remote contro l
5.
The horn honks to con fi rm the remote has
been
programmed .
6
Release the Valet button, and turn the key to the
Off
position .
7.
The horn sounds one long honk to confirm that remote p rogramming has been exited
The programming routine exits
if
ony
of
the following occurs:
The ign ition is turned
off
There is no activity for
30
seconds
The Va let button is pressed too many times
See full Installatio n Gu ide for more
detailed information on this system .
Such information and more can
be
found online at·
www.directechs.com
E L E C T R 0 N
I C S
QRN~Ol lOI I ·I I
LAD42032