Cycles - Kenmore ENERGY HE3T Owner's Manual And Installation Instructions

To add items
1. Select PAUSE/CANCEL. The washer door unlocks, and items
can be added.
2. To continue the cycle, close the door and select and hold
START (for approximately 1 second).
Clothes Clean
The Clothes Clean light stays on for 5 minutes after the cycle is
complete. The washer will then power down.
Locking controls
The Control Lock prevents unintended use of the washer. You
can also use the control lock feature to prevent unintended cycle
or option changes during a cycle. When CONTROL LOCKED is
lit, all buttons are disabled except for Pause/Cancel and Start.
You can lock the controls while the washer is operating.
To lock the controls
Select and hold DRAIN/SPIN for 3 seconds.
DRAIN /
SPiN
PRESS & HOLD 3
SECONDS TO LOCK/
UNLOCK CONTROL
The CONTROL LOCKED status light glows.
To unlock the controls
Select and hold DRAIN/SPIN for 3 seconds until the CONTROL
LOCKED Status light turns off.
Estimated Time Remaining
The cycle times vary automatically based on your water pressure,
water temperature, detergent, and clothes load. The cycle time
will be extended if oversudsing occurs or the load is unbalanced.
Wash Cycles
Choose Wash Cycles by selecting the button next to the desired
cycle. Each cycle is designed for different types of fabric and soil
levels.
WASH O!CLES
EXPRESS W ASH
NORMAL/
CASUAL
T
WHITES
DELICATE
SILK
WOOL
ULTRA
SANITARY HANDWASH
Each cycle has a preset Soil Level (cycle time), Water
Temperature, Spin Speed and may have preset Options. The
preset settings provide the recommended fabric care for the
selected cycle.
The preset settings can be changed anytime before START is
selected. Not all Options and Modifiers are available with all
Cycles. (To change settings after the cycle has started, select
PAUSE/CANCEL, then select the desired settings. Select and
hold START [for approximately 1 second] to continue the
cycle.)
Preset cycle settings
Each cycle has a preset Cycle Time, Water Temp, and Spin
Speed. The preset settings provide the recommended fabric care
for the selected cycle. See chart.
Cycle Soil Level Water Temp Spin
(hr:min) Speed
Sanitary More Extra Hot/Cold High
(2:0o)
Whitest More Hot/Cold High
Whites (1:10)
Heavy More Hot/Cold High
Duty (1:30)
Normal/ Normal Warm/Cold Medium
Casual (0:45) High
Express Less Warm/Cold High
Wash (0:35)
Delicate Normal Warm/Cold Low
(0:35)
Silk Normal Cold/Cold No spin
(0:30)
Wool Normal Cold/Cold Low
(0:35)
Ultra Normal Cold/Cold Extra Low
Handwash (0:35)
Sanitary
Use this cycle to clean heavily soiled colorfast fabrics. This cycle
combines a very hot water temperature and fast speed tumbling
to help ensure the removal of heavy soils and stains. It is
recommended that you set your hot water heater to 120°F (49°C)
to ensure proper performance during this cycle. The Sanitary
cycle also helps eliminate 99.999% of 3 common infectious
bacteria, even when no bleach is used. Extra high speed spin
helps shorten drying time.
Whitest Whites
This cycle is especially designed for cleaning loads of soiled
white fabrics with the addition of bleach. Hot washing
temperatures assure optimal bleach activity. An additional rinse
provides optimal rinse performance to avoid chlorine residues on
your laundry. This cycle combines fast speed tumbling, longer
wash time, and extra high speed spin to shorten drying time.
Heavy Duty
Use this cycle to wash loads of sturdy, colorfast fabrics and
normally soiled garments. This cycle combines fast speed
tumbling, longer wash time, and extra high speed spin to shorten
drying times. If the water temperature is lower than needed for
this cycle, the heater will warm the water to the optimum
temperature.
NOTE: Stain Treat is a default option for this cycle. To ensure best
performance, the water is heated as the cycle progresses. This
gradual heating assists in the removal of organic soils such as
blood. Stain Treat must be turned off to change the modifiers.
14