Kenmore 3948598A Installation Instructions And Use And Care Manual
Kenmore 3948598A Installation Instructions And Use And Care Manual

Kenmore 3948598A Installation Instructions And Use And Care Manual

Coin-operated commercial automatic washer

Advertisement

Quick Links

Coin-Operated
Commercial
Automatic Washer
3948598A
Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com

Advertisement

Table of Contents
loading

Summary of Contents for Kenmore 3948598A

  • Page 1 Coin-Operated Commercial Automatic Washer 3948598A Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com...
  • Page 2: Table Of Contents

    For Sears warranty information or to contact a Sears Service Center, call 1-800-4-MY HOME sM(1-800-469-4663). If you need service or parts for your Kenmore operated washer: When requesting service, be ready to give the model number, serial number (located on a plate under the lid) and date of purchase.
  • Page 3: Installation Requirements

    WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following: • Read all instructions before using the washer. • Do not wash articles that have been previously cleaned...
  • Page 4: Location Requirements

    Additional clearances may be required for wall, door and floor moldings. Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended If a closet door is installed, the minimum air openings in the top and bottom of the door are required (C).
  • Page 5 The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 39" (99 cm) above the floor and no higher than 96" (244 cm) from the bottom of the washer. Floor drain system (view D) The floor drain system requires a siphon break that may be purchased separately.
  • Page 6: Installation Instructions

    Move the washer to within approximately final location. Removing the shipping strap is necessary for smooth operation. If the shipping strap is not removed, the washer will make excessive noise. The washer must be in the upright position before removinig the shipping strap.
  • Page 7: Connect The Inlet Hoses

    For floor drain installation, see kit number required under "Tools and Parts." The washer must be connected to the water faucets using new inlet hoses (not provided). Do not use old hoses. Insert new flat washers into each end of the inlet hoses. Firmly seat the washers in the couplings.
  • Page 8: Secure The Drain Hose

    Properly leveling your washer avoids excessive noise and vibration. Install the front leveling feet 1. Prop up the front of the washer about 4" (10.2 cm) with a wood block or similar object. The block needs to support the weight of the washer.
  • Page 9: Complete Installation

    Failure to do so can result in death or electrical shock. NOTE: The washer was tested at the factory. Some time may have been left so that the washer will start to operate before the coin slide is operated. If this happens, take off the access panel from the top of the meter case and set the clutch to OFF position by hand.
  • Page 10: Washer Cabinet

    2. Remove 2 screws on console at left and right side on bottom. A. Screws Pull console forward then tilt it back. Remove washer cabinet clip on right side under console. Use screwdriver blade as shown. NOTE: For additional security, top can be locked to washer with a lock and key in the hole provided.
  • Page 11: Washer Use

    Plug in washer or reconnect power. NOTE: Refer to the product information coin box for additional information. Never place items in the washer that are dampened with gasoline or other flammable No washer can completely Do not dry anything...
  • Page 12: Washer Care

    Turbine Oil Upper Centerpost Bearings NOTES: • Shut off hot and cold water outlets when washer is not in use. Loading Suggestion • Drain machine to avoid damage if washer will be subjected to freezing temperatures. 2 pair work pants...
  • Page 13: Troubleshooting

    The wash load should be balanced and not overloaded. The fill or spray rinses can deflect off the load. The washer must be level. The front feet should be properly installed and the nuts tightened. Reset the rear leveling legs (if needed).
  • Page 14: Washer Operation

    Follow manufacturer's Washer continues Is the top of drain hose lower than the water level in washer? The top of the hose must be higher than the water level in the washer for proper operation. See the Installation Instructions. Does the drain hose fit too tightly in the standpipe, or is it taped to the standpipe? The drain hose should be loose yet fit securely.
  • Page 15: Washer Results

    Sort lint givers (towels, chenille) from lint takers (corduroy, synthetics). Also sort by color. Did you overload the washer? The wash load must be balanced and not overloaded, Clothes should move freely. Lint can be trapped in the load if overloaded. Wash smaller loads.
  • Page 16 1-800-827-6655 Para pedir servicio de reparaci6n a domicilio, y para ordenar piezas: 1-888-SU-HOGAR (1-888-784-6427) 3948598A © 2006 Sears Brands LLC Your Home your home-of all major brand appliances, or heating and cooling systems, parts, accessories installation of home appliances 1-800-4-MY-HOME ®...

Table of Contents