Table of Contents
Advertisement
Quick Links
Sales +44 (0) 8700 766900
Technical +44 (0) 8700 766902
Salus Controls plc
Enterprise Park, Bala
Gwynedd, LL23 7NL
Regional offices, England & Scotland.
Web: www.salus-tech.com
Email: sales@salus-tech.com
Maintaining a policy of continual product
development Salus Controls plc. reserve the right to
change specification, design and materials of
products listed in this brochure without prior notice.
Manual Issue No. IM-RT500RF-001
In st ru ct io n M a nu al
Programmable
THERMOSTAT
for Model No. RT500RF
Thank you for purchasing this Salus product
- if installing for someone else, please ensure that
the instructions are handed to the householder.
Warning - Please read this manual prior to
installation or use.
Shock Hazard
This unit must be installed by a competent person,
in accordance with BS 7671 (the IEE Wiring
Regulations), or other relevant national regulations
and codes of good practice.
Always isolate the AC Mains supply before removing
the unit from the Industry Standard Back Plate.
Advertisement
Table of Contents
Related Manuals for Salus RTS00RF
Summary of Contents for Salus RTS00RF
- Page 1 Regulations), or other relevant national regulations and codes of good practice. Maintaining a policy of continual product development Salus Controls plc. reserve the right to Always isolate the AC Mains supply before removing change specification, design and materials of the unit from the Industry Standard Back Plate.
-
Page 2: Wiring Diagram
PRIOR TO INSTALLING PLEASE READ Switches/Jumpers: WIRING DIAGRAM THE INSTALLATION GUIDE The installer should select the jumper positions required FOR 230V APPLICATION The RT500RF is easily installed using the Industry if changing from the factory presets-these jumpers are Standard back plate supplied, which can be mounted The unit is default 230V, if volt f found on the rear of the unit. - Page 3 pers: Following table is the settin RF Address Code Setting WIRING DIAGRAM thermostat after reset or P If there is another user nearby, e.g. in the next ect the jumper positions required FOR 230V APPLICATION actory presets-these jumpers are house, your receiver may be fault triggered by their Function Status af The unit is default 230V, if volt free application is...
-
Page 4: User Guide
Default Programme Following table is the setting of the User Guide etting thermostat after reset or Power on: er nearby, e.g. in the next Function Program Weekday (M to F) Weekend (SA may be fault triggered by their Function Status after Reset or Power on select a different RF address Increase Setpoint Temperature Time: 6:00am... -
Page 5: Clock Setting Mode
Default Programme • Press • Release SET and SELECT, press to increase or decrease the "hour" respectively. select the program Program Weekday (M to F) Weekend (SA to SU) set for Weekday / • Press and release SELECT, press Weekend to be increase or decrease the "minute"... -
Page 6: Setting Mode
• Press 5-2 or 7 days program e SET and SELECT, press to increase 7 days program selected ease the "hour" respectively. select the program • The PROG indicator is displa • 5 different sets of Time and Setpoint set for Weekday / nd release SELECT, press indicate the program numbe temperature can be set for each Day of Week. -
Page 7: Frost Protection
5-2 or 7 days program am selected Frost Protection: Temporary Override: • The PROG indicator is displayed accordingly to Time and Setpoint • Press and hold BL/FROST in Normal mode for 3 • Press when reviewing Setpoint indicate the program number. be set for each Day of Week. - Page 8 • The setting range is 10°C - 35°C in steps of Protection: Temporary Override: Reviewing Setpoint T 0.5°C. and hold BL/FROST in Normal mode for 3 • Press when reviewing Setpoint • Press to review the S • Setpoint Temperature will stop flashing when a ds to activate the Frost Protection.
-
Page 9: Lcd Backlight
is 10°C - 35°C in steps of Reviewing Setpoint Temperature: Low-Battery Detectio • Press to review the Setpoint Battery voltage is sampled every ature will stop flashing when a temperature. battery voltage drops to a certa en flashes again once the key is Battery warning indicator appea When any program is running, the LCD will show the program Setpoint temperature with the "SET"... -
Page 10: Low-Battery Detection
Low-Battery Detection: Sleep Mode: Battery voltage is sampled every minute. When the • Press and hold in Normal mode for 3 battery voltage drops to a certain level, the Low- seconds simultaneously to enter the Sleep mode. Battery warning indicator appears. •...