Table of Contents
Advertisement
During this initial phase, the display shows the
working program, which can be modified using but-
tons 5 and 6 on the control panel. To set the desired
room temperature, press buttons 1 and 2. When the
programming phase is complete, the stove contin-
ues working until the selected room temperature is
reached, then the stove goes into
(small pilot flame remains lit).
When the room temperature falls by 2°C relative to
the temperature selected on the control panel, the
stove resumes the program previously set.
To switch off the stove completely, hold down button
4 on the control panel for about 3 seconds.
CONTROLLING THE TIMER-THERMOSTAT
Press button 3 "SET" to access the timer-thermo-
stat programming function, which starts at parame-
ter UT01.
To select subsequent parameters, press button 3
"SET".
To increase or decrease a value, press buttons 1
and 2 repeatedly.
UT01: used to set the day on which the program is
being set, for example if it is Wednesday when you
are programming the timer-thermostat, set parame-
ter UT01 to Day 3 using buttons 1 and 2.
To confirm and continue programming, press button
3 "SET".
UT02: used to set the current clock time; use but-
tons 1 and 2 again to adjust the time as required.
Press 3 "SET" to confirm and continue.
UT03: used to set the minutes; use buttons 1 and 2
again to adjust as required. Press 3 "SET" to con-
firm and continue.
UT04: is not used.
Before we go into the programming phase, it is
important to note that the programmer is designed
to switch on and off twice per day, where AM is the
morning
program
afternoon/evening program.
UT05: used to set the AM switch-on time in steps of
10 minutes.
Press 3 "SET" to confirm and continue.
mode
ECO
and
PM
is
the
UT06: used to set the AM switch-off time in steps of
10 minutes.
Press 3 "SET" to confirm and continue.
UT07: this parameter is used to confirm the day on
which to run the AM program set previously with
parameters UT05 and UT06.
Example: if you want the stove to run the program
on Monday, the lower display must be set to on1.
If you want the stove not to run the AM program on
Monday, the lower display must be set to off1. To
change the setting on the lower display, use buttons
1 and 2. Use button 1 to scroll through the program
days, and button 2 to select ON or OFF.
To go on to the next parameter, press button 3
"SET".
UT08: used to set the PM switch-on time in steps of
10 minutes.
Press 3 "SET" to confirm and continue.
UT09: used to set the PM switch-off time in steps of
10 minutes.
Press 3 "SET" to confirm and continue.
UT10: this parameter is used to confirm the day on
which to run the PM program set previously with
parameters UT08 and UT09. The rest of the pro-
gramming is the same as for parameter UT07.
Press 3 "SET" to confirm and continue.
As an example, if you want to set only one daily pro-
gram, to run continuously over a period from 8:00 in
the morning to 20:00 in the evening, just set param-
eters UT05, UT06 and UT07, with parameter UT05
set to 8:00 and UT06 set to 20:00; then use UT07
to select the day on which this program is to run.
If you do not want to have the stove switch on auto-
matically at all, simply set parameter UT01 to off,
using buttons 1 and 2 again.
In this case, the stove ignores all the other pro-
grammed values, and is only switched on manually.
N.B. you can exit programming mode at any
time by lightly pressing button 4 (ON-OFF).
8
Advertisement
Table of Contents
