Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKVISION US-5 Inch Speed Dome
Summary of Contents for HIKVISION US-5 Inch Speed Dome
- Page 1 5 Inch Speed Dome Installation Manual V2.0.0 2010-01...
- Page 2 5 Inch Speed Dome Installation Manual V2.0.0 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable to 5 Inch Speed Dome. This manual may contain several technically incorrect places or printing errors, and the content is subject to change without notice. The updates will be added into the new version of this manual.
-
Page 3: Safety Instruction
5 Inch Speed Dome Installation Manual V2.0.0 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. -
Page 4: Preparation For Installation
5 Inch Speed Dome Installation Manual V2.0.0 Preparation for Installation Basic requirements All the electronic operation should be strict compliance with the local electrical safety regulations, fire prevention regulations and other related regulations at the installation place. Check whether all the accessories are there according to the packing list, make sure that the place and installation mode are conform to the demands, if not, please contact the supplier. -
Page 5: Table Of Contents
5 Inch Speed Dome Installation Manual V2.0.0 Table of Contents Table of Contents................................. 4 Chapter 1 Installation..............................6 Check Parts List ............................. 6 Installation ..............................6 1.2.1 High Speed Dome and Auto Tracking Speed Dome Installation ............6 1.2.2 Medium Speed Dome and Network High-definition Speed Dome Installation ....... - Page 6 5 Inch Speed Dome Installation Manual V2.0.0 Appendix 2 RS485 Bus Connection .......................... 47 Appendix 3 24VAC Wire Gauge & Transmission Distance ..................50 Appendix 4 Table of Wire Gauge Standards......................51...
-
Page 7: Chapter 1 Installation
5 Inch Speed Dome Installation Manual V2.0.0 Chapter 1 Installation 1.1 Check Parts List Prior to installation, unpack the dome unit and check whether it is in good condition and all parts and accessories are included by referring to the packing list). The power supply for the speed dome is AC24V/3A. - Page 8 5 Inch Speed Dome Installation Manual V2.0.0 etc. 1. Address DIP Switch 2. Protocol DIP Switch 3. Wiring Connector 4. Address and Protocol Settings Figure 1.2.2 Bottom Board of Dome Drive 4. Push the tab locks on the back box interconnect board and lift the hinged door to the circuit board, as shown in Figure 1.2.3. Unplug the video cable, power cord and other cables terminals to avoid cables twisting during the back box installation.
- Page 9 5 Inch Speed Dome Installation Manual V2.0.0 1. Alarm In/Out Terminals (7 inputs/2outputs) 2. Video Out and RS-485 COM Terminals 3. 24VAC Voltage Input and GND Terminals Figure 1.2.4 Back Box Circuit Board (High Speed Dome and Auto Tracking High Speed Dome) 1.Alarm In/Out Terminals (7 inputs/2 outputs) 2.
- Page 10 5 Inch Speed Dome Installation Manual V2.0.0 5. Attach the back box of dome to the mount. Figure 1.2.6 Attach Back Box to Mount for outdoor applications, please apply the thread compound and the damp-proof stopper to threads of the back box and the Note: mount.
-
Page 11: Medium Speed Dome And Network High-Definition Speed Dome Installation
5 Inch Speed Dome Installation Manual V2.0.0 7. Install the bubble and fasten the two set screws on both sides, as shown in Figure 1.2.8. Figure 1.2.8 Install Bubble 1.2.2 Medium Speed Dome and Network High-definition Speed Dome Installation the following installation instructions are applicable to high speed dome, network high speed dome and High-definition network Note: speed Dome models. - Page 12 5 Inch Speed Dome Installation Manual V2.0.0 Figure 1.2.9 Open bubble and remove the expand aple poly ethylene and protective sticker from dome drive 3. Configure the dome address, baud rate and other settings through DIP switch SW1 and SW2 located on the bottom board of the dome, as shown in Figure 1.2.10.
- Page 13 5 Inch Speed Dome Installation Manual V2.0.0 4. Push the tab locks on the back box interconnect board and lift the hinged door to the circuit board, as shown in Figure 1.2.12. Unplug the video cable, power cord and other cables terminals to avoid cables twisting during the back box installation. Refer to Figure 1.2.13 (medium speed dome) and Figure 1.2.14(network medium speed dome) for the wiring terminals.
- Page 14 5 Inch Speed Dome Installation Manual V2.0.0 1.Alarm In/Out Terminals (1 inputs/1 outputs) 2. Audio In/Out, Video Out and RS-485 COM Terminals 3. 24VAC Voltage Input and GND Figure 1.2.14 Back Box Circuit Board (Network Medium Speed Dome and Network High-definition Speed Dome) 5.
-
Page 15: Initial Settings
5 Inch Speed Dome Installation Manual V2.0.0 for outdoor applications, please apply the thread compound and the damp-proof stopper to threads of the back box and the Note: mount. After having made connections of the power cord, video cable, RS-485 control line and alarm input/output lines (if required), close the hinged door and tighten the set screws, as shown in Figure 1.2.15. -
Page 16: Dip Switch Settings
5 Inch Speed Dome Installation Manual V2.0.0 1.4 DIP Switch Settings 1.4.1 DIP Switch Settings for High Speed Dome and Auto Tracking High Speed Dome 1. Address DIP Switch 2. Protocol DIP Switch 3. Wiring Connector 4. Address and Protocol Settings Figure 1.4.1 Bottom Board of Dome Drive The dome provides two DIP switches SW1 and SW2 for setting the dome address, baud rate, protocol, etc. -
Page 17: Dip Switch Settings For Medium Speed Dome And Network High-Definition High Speed Dome
5 Inch Speed Dome Installation Manual V2.0.0 1.4.2 DIP Switch Settings for Medium Speed Dome and Network High-definition High Speed Dome Figure 1.4.2 DIP Switch Location on Side of Dome Drive The circuit board of the dome drive provides two DIP switches SW1 and SW2 for setting the dome address, baud rate, protocol, etc. As shown in Figure 1.4.2, ON=1, OFF=0. - Page 18 5 Inch Speed Dome Installation Manual V2.0.0 Settings for address 0~71 are listed as below: SW1 Position DIP Switch SW1 Settings Address...
- Page 19 5 Inch Speed Dome Installation Manual V2.0.0...
-
Page 20: Baud Rate Settings
5 Inch Speed Dome Installation Manual V2.0.0 1.4.4 Baud Rate Settings The positions 1-3 of DIP Switch SW2 are used for setting the baud rate of dome, respectively as 2400bps, 4800bps, 9600bps, 19200bps and 38400bps. For baud rate out of the above range, the default setting is 2400bps. Refer to the following table: DIP Switch SW2-Baud Rate Settings Baud Rate Positions1-3 Settings... - Page 21 5 Inch Speed Dome Installation Manual V2.0.0 network high-definition speed dome can connect with 1 alarm inputs (0~12VDC) and 1 alarm outputs. Refer to the following diagram: The alarm provides the relay output (no voltage), and the external power supply is required when it connects to the alarm device. For DC power supply (left diagram), the input voltage must be within the range of 12VDC, 30mA.
-
Page 22: Chapter 2 Mounts Dimension
5 Inch Speed Dome Installation Manual V2.0.0 Chapter 2 Mounts Dimension 2.1 Long-arm Wall Mount ... -
Page 23: Short-Arm Wall Mount
5 Inch Speed Dome Installation Manual V2.0.0 2.2 Short-arm Wall Mount 2.3 Corner Adapter... -
Page 24: Pole Adapter
5 Inch Speed Dome Installation Manual V2.0.0 2.4 Pole Adapter 2.5 Pendant Adapter ... -
Page 25: Chapter 3 Wall Mounting Applications
5 Inch Speed Dome Installation Manual V2.0.0 Chapter 3 Wall Mounting Applications 3.1 Mounting Components Wall Mount Applicable to indoor/outdoor pendant domes. Mounting Accessories Nuts and Flat Washers 3.2 Wall Mounting Instructions The wall mounting is applicable to the indoor/outdoor solid wall construction which should comply with the following mounting requirements: ... - Page 26 5 Inch Speed Dome Installation Manual V2.0.0 Step1: Drill mounting holes in the wall and install the expansion screws Drill four holes in the wall according to the mounting locations, and then insert M6 expansion screws (not supplied) into the mounting holes.
- Page 27 5 Inch Speed Dome Installation Manual V2.0.0 Step3: Install dome to the mount Feed cables through the opening on top of the back box, screw the back box into the threads in the mount, and then use M3 screws to secure the dome.
-
Page 28: Chapter 4 Corner Mounting Applications
5 Inch Speed Dome Installation Manual V2.0.0 Chapter 4 Corner Mounting Applications 4.1 Mounting Components Wall Mount Applicable to the indoor/outdoor pendant domes with the use of corner adapter, wall adapter or pole adapter. Corner Adapter For use with the wall mount in the corner mounting applications. ... -
Page 29: Corner Mounting Instructions
5 Inch Speed Dome Installation Manual V2.0.0 4.2 Corner Mounting Instructions The corner mounting is applicable to the indoor/outdoor 90° solid corner construction which should comply with the following mounting requirements: The wall must be thick enough to install the expansion screws. ... - Page 30 5 Inch Speed Dome Installation Manual V2.0.0 Step3: Install dome to the mount Feed the cables through the opening on top of the back box, and attach the dome to the mount. Finally, use M3 screws to secure the two units. Refer to Section 1.2 for installation instructions. Follow the same instructions described above for the Short-arm Corner Mount installation.
-
Page 31: Chapter 5 Pole Mounting Applications
5 Inch Speed Dome Installation Manual V2.0.0 Chapter 5 Pole Mounting Applications 5.1 Mounting Components Wall Mount Applicable to indoor/outdoor pendant domes with the use of corner adapter, wall adapter or pole adapter. Pole Adapter For use with the wall mount in the pole mounting applications. -
Page 32: Pole Mounting Instructions
5 Inch Speed Dome Installation Manual V2.0.0 Stainless Steel Straps For use with the pole adapter, with the following dimensions selectable: φ59-82mm, φ84-108mm, φ103-127mm, φ130-152mm, φ155-178mm, φ180-203mm, φ194-216mm; Customized dimensions can also be provided according to user’s demand. Mounting Accessories Hex Screws (M8×30) and Spring Washers 5.2 Pole Mounting Instructions ... - Page 33 5 Inch Speed Dome Installation Manual V2.0.0 Step1: Assemble the pole mount adapter Use a screwdriver to loosen the three stainless steel straps and then insert them through the rectangle holes on the pole adapter. Step2: Install pole adapter Feed the control line, video cable and power cable through the central opening and secure the three stainless steel straps to the pole, and finally use the screwdriver to fasten the screws at the steel straps.
- Page 34 5 Inch Speed Dome Installation Manual V2.0.0 Step3: Install wall mount assembly Screw four hex screws with the spring washers to the pole adapter through the wall mount and gasket. Step4: Install dome to the mount Feed the cables through the opening on top of the back box, and attach the dome to the mount, and finally use M3 screws to secure the dome.
-
Page 35: Chapter 6 Pendant Mounting Applications
5 Inch Speed Dome Installation Manual V2.0.0 Chapter 6 Pendant Mounting Applications 6.1 Mounting Components Mounting Base Applicable to pendant domes with the use of the pendant pole and pole adapter. Pendant Pole Pendant Adapter... -
Page 36: Pendant Mounting Instructions
5 Inch Speed Dome Installation Manual V2.0.0 6.2 Pendant Mounting Instructions The pendant mounting is applicable to the indoor/outdoor solid ceiling construction which should comply with the following mounting requirements: The ceiling must be thick enough to mount the expansion screws. ... - Page 37 5 Inch Speed Dome Installation Manual V2.0.0 Step2: Install the pendant pole Swivel the pendant adapter into the matching pendant pole and then use the retainer screws to secure the two parts. Pull out the cables through the pendant pole and screw the pendant pole into the mounting base and use the set screws to secure the two parts as well. For outdoor applications, please apply the water-proof thread compound to the threads.
-
Page 38: Chapter 7 Surface Mounting Applications
5 Inch Speed Dome Installation Manual V2.0.0 Chapter 7 Surface Mounting Applications The surface mounting is applicable to the indoor/outdoor solid ceiling construction which should comply with the following mounting requirements: The ceiling must be with the thickness of 5~40mm. ... - Page 39 5 Inch Speed Dome Installation Manual V2.0.0 Mark Mounting Holes Step2: Use fasteners to secure the mounting base to the ceiling by using screws. If the dome is installed to the wooden wall, directly use the self-tapping screws to secure the mounting base to the wall. ...
- Page 40 5 Inch Speed Dome Installation Manual V2.0.0 ② Push forwards Line up ① Push upwards Lock clip Step4: Install dome drive Take out the dome drive from the packing case, and check whether the drive has any damages or abnormal conditions. Set the baud rate, control protocol and address of the dome by referring to the Operation Installation Manual of Speed Dome.
- Page 41 5 Inch Speed Dome Installation Manual V2.0.0 Step 5: Install the bubble Attach the lower dome with the bubble to the dome drive and swivel in clockwise direction to secure the bubble in place. In order to maintain clear video images, do not touch the internal or outer part of the dome with your hands direcly or with other Note: materials which will cause pollution to the dome.
-
Page 42: Chapter 8 In-Ceiling Mounting Applications
5 Inch Speed Dome Installation Manual V2.0.0 Chapter 8 In-ceiling Mounting Applications 8.1 Installation Conditions The in-ceiling mounting is applicable to the indoor ceiling construction which should comply with the following mounting requirements: The height above the ceiling must be more than 250mm. ... - Page 43 5 Inch Speed Dome Installation Manual V2.0.0 Step2: Connect cables Open the hinged door and feed the power cord, video cable, control line and network cable through the opening of the back box, and then connect all wiring to corresponding sockets located on the circuit board. After connections, close the hinged door. The red LED indicator will light when the power is applied to the unit.
- Page 44 5 Inch Speed Dome Installation Manual V2.0.0 Push the in-ceiling mounting base into the mounting hole in the ceiling, and use the screwdriver to tighten the set screws which will automatically compress the ceiling and secure the mounting base. Step4: Install the dome drive Take out the dome drive from the packing case, and check whether the drive has any damages or abnormal conditions.
- Page 45 5 Inch Speed Dome Installation Manual V2.0.0 Step5: Install the bubble and trim ring Attach the lower dome with the bubble to the dome drive and swivel in clockwise direction to secure the bubble in place. Attach the trim ring to the bubble and aling the triangular prism of the trim ring with the arrow direction tag on the in-celing mounting base.
- Page 46 5 Inch Speed Dome Installation Manual V2.0.0...
-
Page 47: Appendix 1 Lightning & Surge Protection
5 Inch Speed Dome Installation Manual V2.0.0 Appendix 1 Lightning & Surge Protection This product adopts TVS plate lightning protection technology to avoid damage caused by pulse signal that is below 3000W, like instantaneous lighting, surging, etc. According to the actual situation outdoors, necessary protection measures must be taken to secure the electrical safety. -
Page 48: Appendix 2 Rs485 Bus Connection
5 Inch Speed Dome Installation Manual V2.0.0 Appendix 2 RS485 Bus Connection 1. General Property of RS485 Bus According to RS485 industry bus standard, RS485 is a half-duplex communication bus which has 120Ω characteristic impendence, the maximum load ability is 32 payloads (including controller device and controlled device). 2. - Page 49 5 Inch Speed Dome Installation Manual V2.0.0 Figure 3 4. Problems in the Practical Application Normally, users adopt star-shape connection method in construction, under this situation, the terminal resistors must be connected between two farthest devices (as Figure 4, 1# and 15#), but this connection method is not satisfy the requirement of the RS485 industry standard so that it will lead to some problems such as signal reflection, anti-jamming ability decline when the devices are faraway.
- Page 50 5 Inch Speed Dome Installation Manual V2.0.0 Figure 5 1. FAQ of RS485 Bus...
-
Page 51: Appendix 3 24Vac Wire Gauge & Transmission Distance
5 Inch Speed Dome Installation Manual V2.0.0 Appendix 3 24VAC Wire Gauge & Transmission Distance The following table has described the recommended max. distance adopted for the certain wire gauge when the 24VAC voltage loss rate is less than 10%. For the AC driven device, the maximum voltage loss rate allowable is 10%. For example, for a device with the rating power of 80VA which is installed at a distance of 35 feet (10m) away from the transformer, then the minimum wire gauge required is 0.8000mm. -
Page 52: Appendix 4 Table Of Wire Gauge Standards
5 Inch Speed Dome Installation Manual V2.0.0 Appendix 4 Table of Wire Gauge Standards... - Page 53 5 Inch Speed Dome Installation Manual V2.0.0...