Worx WG108 Manual page 12

shaft (See Fig C1).
4) Position the knob and screw through the
auxiliary handle and bracket, and tighten knob
(turn clockwise). Do not tighten completely
until you have adjusted the auxiliary handle to
your desired working position.
3. AdjuSTiNG AuxiliARy hANdlE
(See Fig C2)
1) The auxiliary handle's bracket can be moved
up or down on the shaft and the auxiliary
handle itself can be moved forward or
backward into 4 different locked positions
(See Fig C2).
2) When the handle is in desired position, turn
knob and tighten securely.
4. AdjuST ThE hEiGhT (See Fig d1, d2)
The trimmer's telescopic shaft comes in the
collapsed position.
1) To raise the telescopic shaft, pull (separate)
both the top and bottom collars apart (See Fig
D1), and pull (raise) the bottom section of the
shaft up to the desired height. It will click into
nay one of the notches on the shaft, and lock
12 12
into place.
2) Release both collars to lock the shaft into
place (See Fig D2).
3) To lower or collapse the shaft simply pull the
bottom collar down and lower the shaft.
5. AdjuST ThE CuTTiNG ANGlE
(See Fig E)
Your trimmer has a 4-position tilting head that
easily adjusts to the desired working angle
for optimum operator control and comfort. To
adjust the trimmer head angle:
1) Disconnect the trimmer from the power
supply.
wARNiNG: To avoid injury, AlwAyS
turn off and disconnect the trimmer
from the power outlet bEFoRE installing
parts or cleaning the trimmer or making
any adjustments.
2) Press the trimmer head adjustment button
on the motor housing (See Fig e).
3) Move the trimmer head to one of four
different angles and release the button.
Head will click into position. easily readjust
the angle to a more comfortable or efficient
2-in-1 Grass Trimmer/Edger
position as needed.
wARNiNG: bEFoRE connecting
your trimmer to the power outlet,
bE SuRE you are not pressing in on the
trigger switch. Failure to do so could
result in accidental start-up, which may
cause serious personal injury.
6. RoTATE REAR hANdlE ANd uPPER
ShAFT 180° (See Fig F1, F2)
1) Disconnect the trimmer from the power
supply.
2) To rotate the top shaft 180o, pull (separate)
both the top and bottom collars apart (See Fig
F1), and rotate the top shaft with rear handle
(and auxiliary handle) 180°.
Release both collars and shaft will lock in
place.
3) Your trimmer is ready for use as an edger
(See Fig F1,F2).
7. SElECT AN ExTENSioN CoRd
wARNiNG! use only a voltage
supply as specified on your unit.
Extension Cord Gauge Cord
length of Cord
25 Ft. (7.5m)
50 Ft. (15m)
100 Ft. (30m)
extension cords are available for this unit.
8. PiGTAil PowER CoRd
(See Fig G1, G2)
Your trimmer/edger has a 12-inch pigtail power
cord. This cord must be attached to a proper
extension cord. Remove the plug guard from
the pigtail power cord. Make a loop in the
extension cord. Push loop through hole in the
handle (See Fig G1). Fasten loop around cord
retention hook. Plug trimmer's power cord into
extension cord plug (See Fig G2).
OPERATION INSTRUCTIONS
1. oN/oFF TRiGGER (See Fig h)
Press and hold the trigger to operate the
Gauge
18 Gauge
16 Gauge
16 Gauge
EN